Eaton 9E User manual

80–200 kVA (380/400/415V)
Installation and Operation Manual
Eaton®9E UPS

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and
maintenance of the UPS and batteries. Please read all instructions before operating the equipment
and save this manual for future reference.
CONSIGNES DE SÉCURITÉ IMPORTANTES CONSERVER CES INSTRUCTIONS
Ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de toute
procédure d'installation et de maintenance des batteries et de l'onduleur. Veuillez consulter
entièrement ces instructions avant de faire fonctionner l'équipement et conserver ce manuel afin
de pouvoir vous y reporter ultérieurement
Eaton, Powerware, and Mini-Slot are registered trademarks and ConnectUPS is a trademark of Eaton
Corporation or its subsidiaries and affiliates. Modbus is a registered trademark of Schneider Electric.
National Electrical Code and NEC are registered trademarks of National Fire Protection Association, Inc.
All other trademarks are property of their respective companies.
©Copyright 2012 Eaton Corporation, BAOAN, SZ, CHINA. All rights reserved. No part of this document
may be reproduced in any way without the express written approval of Eaton Corporation.

Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual i
Table of Contents
1 INTRODUCTION...................................................................................... 1-1
1.1 UPSStandardFeatures ................................................................. 1-2
1.1.1 InstallationFeatures............................................................... 1-2
1.1.2 ControlPanel .................................................................... 1-2
1.1.3 CustomerInterface................................................................ 1-2
1.1.4 High-Efficiency Mode.............................................................. 1-2
1.1.5 AdvancedBatteryManagement...................................................... 1-2
1.2 OptionsandAccessories................................................................ 1-2
1.2.1 ExternalBatteryCabinet............................................................ 1-2
1.2.2 TieCabinet...................................................................... 1-3
1.2.3 ParallelSystem................................................................... 1-3
1.2.4 MonitoringandCommunication...................................................... 1-3
1.2.5 MaintenanceBypass .............................................................. 1-4
1.3 BatterySystem........................................................................ 1-3
1.4 BasicSystemConfigurations............................................................. 1-3
1.5 UsingThisManual ..................................................................... 1-3
1.6 ConventionsUsedinThisManual.......................................................... 1-4
1.7 Symbols,Controls,andIndicators ......................................................... 1-4
1.8 ForMoreInformation................................................................... 1-4
1.9 GettingHelp.......................................................................... 1-5
2 SAFETYWARNINGS.................................................................................. 2-1
SECTION 1—INSTALLATION
3 UPSINSTALLATIONPLANANDUNPACKING............................................................. 3-1
3.1 CreatinganInstallationPlan.............................................................. 3-1
3.2 PreparingtheSite...................................................................... 3-1
3.2.1 Environmental and Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2.2 UPSSystemPowerWiringPreparation................................................. 3-6
3.2.3 UPS System Interface Wiring Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.3 Inspecting and Unpacking the UPS Cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
4 UPSSYSTEMINSTALLATION.......................................................................... 4-1
4.1 PreliminaryInstallationInformation........................................................ 4-1
4.2 Unloading the UPS Cabinetfrom the Pallet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.3 ExternalBatteryCabinetInstallation........................................................ 4-4
4.4 ExternalPowerWiringInstallation ......................................................... 4-5
4.5 InstallingInterfaceConnections........................................................... 4-8
4.5.1 Installing Building Alarm Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
4.5.2 Installing Parallel Pull Chain and CAN Control Wiring and Connections . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
4.5.3 Installing Mini-Slot Interface Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
4.6 InstallingaREPOSwitch ................................................................ 4-15
4.7 InitialStartup ......................................................................... 4-17
4.8 CompletingtheInstallationChecklist....................................................... 4-17

Table of Contents
ii Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual
SeCTIon 2—oPeraTIon
5 underSTandInguPSoPeraTIon.................................................................... 5-1
5.1 UPSSystemOverview.................................................................. 5-1
5.2 SingleUPS........................................................................... 5-2
5.2.1 Modes ......................................................................... 5-2
5.2.2 Standard Normal Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.2.3 High-EfficiencyMode.............................................................. 5-3
5.2.4 BypassMode.................................................................... 5-4
5.2.5 BatteryMode.................................................................... 5-5
5.3 Single UPS Unit System Oneline Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
6 uPSoPeraTIngInSTruCTIonS....................................................................... 6-1
6.1 UPSControlsandIndicators.............................................................. 6-1
6.1.1 ControlPanel .................................................................... 6-2
6.2 UsingtheControlPanel................................................................. 6-3
6.2.1 StatusIndicators.................................................................. 6-3
6.2.2 SystemEvents................................................................... 6-4
6.2.3 UsingtheLCDandPushbuttons...................................................... 6-5
6.2.4 UsingtheMenu .................................................................. 6-6
6.2.5 MimicScreen.................................................................... 6-6
6.2.6 DisplayMenuOperation............................................................ 6-7
6.2.7 SystemControls.................................................................. 6-9
6.3 SingleUPSOperation................................................................... 6-11
6.3.1 Starting the UPS in Standard Normal Mode (Default Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
6.3.2 StartingtheUPSinBypassMode..................................................... 6-11
6.3.3 Transfer from Normal to Bypass Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
6.3.4 Transfer from Bypass to Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
6.3.5 Transfer from Standard Normal Mode to HE mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
6.3.6 Transfer from HE Mode to Standard Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
6.3.7 Transfer from Normal Mode to Internal Maintenance Bypass (Optional on 80-120kVA) . . . . . . . . . . . . 6-13
6.3.8 Transfer from Internal Maintenance Bypass to Normal Mode (Optional on 80-120kVA) . . . . . . . . . . . . 6-14
6.3.9 UPS and Critical Load Shutdown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
6.3.10 ChargerControl .................................................................. 6-15
6.3.11 BatteryTest...................................................................... 6-15
6.3.12 UsingtheUPSLOADOFFCommand.................................................. 6-15
6.3.13 Using the Remote Emergency Power-off Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
6.4 MultipleUPSParallelOperation........................................................... 6-17
6.4.1 Starting the Parallel UPS in Standard Normal Mode (Default Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
6.4.2 Starting the Parallel UPS in Bypass Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
6.4.3 Transfer from Normal to Bypass Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
6.4.4 Transfer from Bypass to Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19
6.4.5 SingleUPSShutdown.............................................................. 6-19
6.4.6 SingleUPSRestart................................................................ 6-20
6.4.7 UPS and Critical Load Shutdown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20
6.4.8 ChargerControl .................................................................. 6-21
6.4.9 BatteryTest...................................................................... 6-21
6.4.10 UsingtheUPSLOADOFFCommand.................................................. 6-22
6.4.11 Using the Remote Emergency Power-off Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-23

Table of Contents
Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual iii
7 COMMUNICATION ................................................................................... 7-1
7.1 Mini-SlotCards........................................................................ 7-1
7.2 BuildingAlarmMonitoring............................................................... 7-1
8 UPSMAINTENANCE.................................................................................. 8-1
8.1 ImportantSafetyInstructions............................................................. 8-1
8.2 PerformingPreventativeMaintenance...................................................... 8-2
8.2.1 DAILYMaintenance ............................................................... 8-2
8.2.2 MONTHLYMaintenance............................................................ 8-2
8.2.3 ANNUALMaintenance............................................................. 8-3
8.2.4 BATTERYMaintenance............................................................. 8-3
8.3 InstallingBatteries..................................................................... 8-4
8.4 RecyclingtheUsedBatteryorUPS ........................................................ 8-4
8.5 MaintenanceTraining................................................................... 8-4
9 PRODUCT SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
9.1 ModelNumbers....................................................................... 9-1
9.2 Specifications......................................................................... 9-1
9.2.1 UPSInput....................................................................... 9-1
9.2.2 UPSOutput ..................................................................... 9-2
9.2.3 UPSEnvironmental................................................................ 9-2

Table of Contents
iv Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual
This page intentionally left blank.

Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual v
List of Figures
Figure1-1. Eaton9EUPS(80–200kVA).............................................................. 1-1
Figure 3-1. UPS Cabinet Dimensions (Front and Right Side Views) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Figure 3-2. UPS Cabinet Dimensions (Top and Bottom Views) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Figure 3-4. UPS Cabinet as Shipped on Pallet (wood container removed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Figure4-1. RemovingtheFrontShippingBracket....................................................... 4-2
Figure4-2. AttachingtheRamptothePallet .......................................................... 4-3
Figure4-3. RemovingtheRearShippingBracket....................................................... 4-3
Figure4-4. RollingtheCabinetDowntheRamp........................................................ 4-4
Figure4-6. PowerTerminalLocations................................................................ 4-7
Figure4-7. PowerTerminalDetail................................................................... 4-8
Figure4-9. InterfaceTerminalLocations.............................................................. 4-9
Figure 4-10. InterfaceTerminal Detail (Terminal Cover Removed). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Figure 4-11. Building AlarmTerminal Block Connector Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Figure4-12. InterfaceWiringAccess................................................................. 4-12
Figure 4-13. Pull ChainTerminal Block Connector Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Figure4-14. ParallelUPSControlWiring .............................................................. 4-15
Figure4-15. ParallelUPSsystemconnections.......................................................... 4-15
Figure 4-16. REPO Terminal Block Connector Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17
Figure4-17. Normally-OpenREPOSwitchWiring ....................................................... 4-18
Figure 4-18. Normally-Closed REPO Switch Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
Figure5-1. MainElementsoftheUPSSystem ........................................................ 5-1
Figure 5-2. Path of CurrentThrough the UPS in standard Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Figure 5-3. Path of CurrentThrough the UPS in Bypass Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Figure 5-4. Path of CurrentThrough the UPS in Battery Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Figure 5-5. UPS System Oneline – External Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Figure6-1. UPSControlsandIndicators.............................................................. 6-1
Figure6-2. UPSSwitches......................................................................... 6-2
Figure6-3. UPSControlPanel ..................................................................... 6-3
Figure6-4. PartsoftheLCD....................................................................... 6-5
Figure6-5. MainMenuandMimicScreen............................................................ 6-6
Figure6-6. TypicalInitialSetupScreen............................................................... 6-9
Figure6-7. TypicalSystemControlScreen............................................................ 6-10
Figure 6-8. 80-120kVA Optional internal Maintenance Bypass switch arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
Figure7-1. OptionalMini-SlotCards................................................................. 7-1
Figure8-1. AirFilterLocation...................................................................... 8-3

List of Figures
vi Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual
This page intentionally left blank.

Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual vii
List of Tables
Table3-1. UPSCabinetWeights................................................................... 3-2
Table3-2. UPSCabinetClearances................................................................. 3-2
Table 3-3. 9ERequiredClearance ................................................................. 3-2
Table 3-4. Air Conditioning or Ventilation Requirements During Full Load Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Table 3-5. Input/Output Ratings and External Wiring Requirements for the Eaton 9E 80-200kVA . . . . . . . . . . . . . . . . . . 3-7
Table 3-6. UPS External Power CableTerminations for the Eaton 9E 80-200kVA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Table 3-7. Recommended Input Circuit Breaker Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Table 3-8. Recommended Bypass and Output Circuit Breaker Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Table 3-9. Recommended DC input circuit breaker rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Table4-1. BuildingAlarmConnections.............................................................. 4-10
Table4-2. PullChainConnections.................................................................. 4-13
Table4-3. REPOConnections..................................................................... 4-17
Table 4-4. Normally-Open REPO WireTerminations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
Table 4-5. Normally-Closed REPO WireTerminations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
Table6-1. StatusIndicators ...................................................................... 6-3
Table6-2. DisplayFunctionMenuMap.............................................................. 6-6
Table6-3. DisplayMenuOperation................................................................. 6-7
Table6-4. CommandMenuOperation.............................................................. 6-10
Table6-5. TypicalSystemStatusMessages.......................................................... 6-10

List of Tables
viii Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual
This page intentionally left blank.

Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual 1-1
Chapter 1 Introduction
The Eaton9E 80-200kVA uninterruptible power supply (UPS) is a true online, continuous-duty, transformer-free,
double-conversion, solid-state, three-phase system, providing conditioned and uninterruptible AC power to
protect the customer's load from power failures.
The Eaton 9E 80-200 kVA online power protection system is used to prevent loss of valuable electronic
information, minimise equipment downtime, and minimise the adverse effect on production equipment due to
unexpected power problems.
The Eaton 9E 80-200 kVA UPS continually monitors incoming electrical power and removes the surges, spikes,
sags, and other irregularities that are inherent in commercial utility power. Working with a building's electrical
system, the UPS system supplies clean, consistent power that sensitive electronic equipment requires for
reliable operation. During brownouts, blackouts, and other power interruptions, batteries provide emergency
power to safeguard operation.
The UPS is housed in a single free-standing cabinet, with safety shields behind the door for hazardous voltage
protection. Figure1-1 shows the Eaton 9E 80-200 kVA UPS.
Figure 1-1. Eaton 9E UPS (80-200kVA)
Startup may be performed by the customer’s qualified electrical contractor for single (not
parallel) UPS installations without any accessory cabinets.
Startup and operational checks for parallel systems or installations with accessory
cabinets must be performed by an authorised Eaton Customer Service Engineer, or the
warranty terms may become void. This service is offered as part of the sales contract for
the UPS. Contact an Eaton service representative in advance (usually a two-week notice
is required) to reserve a preferred startup date.
NOTE 1
NOTE 2
Eaton 9E UPS (40–60 kVA, 208/220V) Installation and Operation Manual P-164000058—Rev 2 1-1
Chapter 1 Introduction
The Eaton®9E 40–60 kVA uninterruptible power supply (UPS) is a true online, continuous-duty,
transformerless, double-conversion, solid-state, three-phase system, providing conditioned and uninterruptible
AC power to protect the customer's load from power failures.
The Eaton 9E 40–60 kVA online power protection system is used to prevent loss of valuable electronic
information, minimize equipment downtime, and minimize the adverse effect on production equipment due to
unexpected power problems.
The Eaton 9E 40–60 kVA UPS continually monitors incoming electrical power and removes the surges, spikes,
sags, and other irregularities that are inherent in commercial utility power. Working with a building's electrical
system, the UPS system supplies clean, consistent power that sensitive electronic equipment requires for
reliable operation. During brownouts, blackouts, and other power interruptions, batteries provide emergency
power to safeguard operation.
The UPS is housed in a single free-standing cabinet, with safety shields behind the door for hazardous voltage
protection. Figure 1-1 shows the Eaton 9E 40–60 kVA UPS.
Figure 1-1. Eaton 9E UPS (40–60 kVA)
NOTE 1 Startup may be performed by the customer’s battery qualified electrical contractor
for single (not parallel) UPS installations without any accessory cabinets such as an
External Battery Cabinet.
NOTE 2 Startup and operational checks for parallel systems or installations with accessory
cabinets must be performed by an authorized Eaton Customer Service Engineer, or
the warranty terms specified on page W-1 become void. This service is offered as
part of the sales contract for the UPS. Contact an Eaton service representative in
advance (usually a two-week notice is required) to reserve a preferred startup date.
Only

Introduction
1-2 Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual
The UPS has many standard features that provide cost-effective and consistently reliable power protection.
The descriptions in this section provide a brief overview of the UPS standard features.
1.1.1 Installation Features
Power wiring can be routed to the bottom of the cabinet with connections made to easily accessible terminals.
Control wiring is routed through the right of the cabinet and must be installed in accordance with Class1
wiring methods.
1.1.2 Control Panel
The control panel, located on the front of the UPS, contains a liquid crystal display (LCD) and pushbutton
switches to control the operation of the UPS and to display the status of the UPS system. See Chapter6,
“UPS Operating Instructions,” for additional information.
1.1.3 Customer Interface
• Building Alarm Monitoring – Up to three inputs in the UPS are available to connect the facility's alarm
system contacts. Some system configurations may limit the number of inputs available.The UPS uses
these inputs to monitor the building alarms in addition to the UPS status. See Chapter 7,
“Communication,” for additional information.
• Mini-Slot Communication Bays –Two communication bays are standard equipment. One to two optional
Mini-Slot connectivity cards can be installed in the UPS module at any time. Mini-Slot cards are quickly
installed at the front (behind door) of the UPS and are hot-pluggable. See Chapter 7, “Communication,” for
additional information.
1.1 UPS Standard Features
1.1.4 High-Efficiency Mode
The 9E Series UPS offers a High-Efficiency (HE) normal mode with double-conversion on demand that allows
the UPS to operate in standby bypass mode.This mode allows the 9E UPS to achieve 98% efficiency while still
protecting the load. See Chapter6, “UPS Operating Instructions,” for additional information.on setting the UPS
to work in High Efficiency mode.
1.1.5 Advanced Battery Management
A three-stage charging system increases battery service life by optimising recharge time, and protects
batteries from damage due to high current charging and inverter ripple currents. Charging at high currents can
overheat and damage batteries.
1.2 Options and Accessories
Contact an Eaton sales representative for information about the following options.
1.2.1 External Battery Cabinet
Battery backup protection is provide by equipping the UPS system with up to four External Battery Cabinets
(EBCs) containing sealed lead-acid, maintenance-free batteries. The EBCs are housed in single, free-standing
cabinets designed for line-up-and-match installation, but may be installed separate from the UPS cabinet.
1.2.2 Tie Cabinet (System Parallel Module)
ATie Cabinet provides the ability to parallel up to four UPSs together for increased capacity and/or redundant
capability and may also include a system bypass switch.TheTie Cabinet is a free-standing cabinet designed to
be installed separate from the UPS cabinet.

Introduction
Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual 1-3
1.2.3 Parallel System
A parallel UPS system with up to four UPSs can be installed to provide a parallel capacity and/or redundant
system.This load sharing system provides more capacity than a single UPS, and can provide backup,
depending on the load and configuration. In addition, when one UPS is taken out of service for maintenance or
is not operating properly, a redundant UPS continues to supply uninterrupted power to the critical load. A
Controller Area Network (CAN) Bridge provides connectivity for system metering and operational mode
control.The parallel system consists of two to four UPSs each with a parallel CAN Bridge, and aTie Cabinet or
System Parallel Module to act as a tie point and to control the output.
1.2.4 Monitoring and Communication
Mini-Slot Cards – Optional Mini-Slot cards support several protocols, such as SNMP, HTTP, Modbus®and
RS232.See Chapter7, “Communication,“ for additional information on monitoring and communication
features.
1.2.5 Maintenance Bypass
The optional internal Maintenance Bypass for 80-120kVA models consists of input, output and bypass
switches used to control the AC input to the UPS the inverter output, and a Maintenance Bypass switch used
to partially isolate the UPS so that a limited number of components can be serviced without interrupting power
to critical systems.
1.3 Battery System
The battery system is in an external cabinet. The battery system provides emergency short-term backup power
to safeguard operation during brownouts, blackouts, and other power interruptions.The battery system is
equipped with lead-acid batteries.
1.4 Basic System Configurations
The following basic UPS system configurations are possible:
• Single UPS with one to four external battery cabinets
• Single UPS with external batteries and accessory cabinets
The UPS system configuration can be enhanced by adding optional accessories such as a
Remote Emergency Power-off (REPO) control or Mini-Slot communication cards.
1.5 Using This Manual
This manual describes how to install and operate the Eaton 9E 80-200 kVA. Read and understand the
procedures described in this manual to ensure trouble-free installation and operation. In particular, be
thoroughly familiar with the REPO procedure (see paragraph6.3.13).
The information in this manual is divided into sections and chapters.Thesystem, options, and accessories
being installed dictate which parts of this manual should be read. At a minimum, Chapters1 through4
andChapter6 should be examined.
Read through each procedure before beginning the procedure. Perform only those procedures that apply to
the UPS system being installed or operated.

Introduction
1-4 Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual
1.6 Conventions Used in This Manual
This manual uses these type conventions:
• Bold type highlights important concepts in discussions, key terms in procedures, and menu options, or
represents a command or option that you type or enter at a prompt.
• Italic type highlights notes and new terms where they are defined.
• Screen type represents information that appears on the screen or LCD.
Icon Description
Note Information notes call attention to important features or instructions.
[Keys] Brackets are used when referring to a specific key, such as [Enter] or [Ctrl].
In this manual, the term UPS refers only to the UPS cabinet and its internal elements.The term UPS system
refers to the entire power protection system–the UPS cabinet, an external battery system, and options or
accessories installed.
1.7 Symbols, Controls, and Indicators
The following are examples of symbols used on the UPS or accessories to alert you to important information:
RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric
shock symbol.
CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's manual for
additional information, such as important operating and maintenance instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries in
the trash. This product contains sealed, lead-acid batteries and must be disposed of
properly. For more information, contact your local recycling/reuse or hazardous waste
centre.
This symbol indicates that you should not discard waste electrical or electronic
equipment (WEEE) in the trash. For proper disposal, contact your local recycling/reuse
or hazardous waste centre.
1.8 For More Information
Refer to the External Battery Cabinet Installation Manual for the following additional information:
• Installation instructions, including site preparation, planning for installation, wiring and safety information,
and detailed illustrations of cabinets with dimensional and connection point drawings
Visit www.eaton.com/powerquality or contact an Eaton service representative for information on how to
obtain copies of these manuals.

Introduction
Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual 1-5
1.9 Getting Help
If help is needed with any of the following:
• Scheduling initial startup
• Regional locations and telephone numbers
• A question about any of the information in this manual
• A question this manual does not answer
Please call your local service representative.

Introduction
1-6 Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual
This page intentionally left blank.

Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual 2-1
Chapter 2 Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
This manual contains important instructions that should be followed during installation and
maintenance of the UPS and batteries. Read all instructions before operating the equipment and
save this manual for future reference.
The UPS is designed for industrial or computer room applications, and contains safety shields
behind the door and front panels. However, the UPS is a sophisticated power system and should be
handled with appropriate care.
DANGER
This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by
AUTHORISED SERVICE PERSONNEL ONLY.There are NO USER SERVICEABLE PARTS inside the
UPS.
WARNING
• The UPS is suitable for mounting on concrete or other non-combustible surfaces only.
• The UPS is powered by its own energy source (batteries).The output terminals may carry live
voltage even when the UPS is disconnected from an AC source.
• To reduce the risk of fire or electric shock, install this UPS in a temperature and humidity
controlled, indoor environment, free of conductive contaminants. Ambient temperature must not
exceed 40°C (104°F). Do not operate near water or excessive humidity (95%?maximum).The
system is not intended for outdoor use.
• As a result of the connected loads high leakage current is possible. Connection to earth ground is
required for safety and proper product operation. Do not check UPS operation by any action that
includes removal of the earth (ground) connection with loads attached.
• Ensure all power is disconnected before performing installation or service.
• Batteries can present a risk of electrical shock or burn from high short-circuit current.The
following precautions should be observed: 1) Remove watches, rings, or other metal objects;
2) Use tools with insulated handles; 3) Do not lay tools or metal parts on top of batteries; 4) Wear
rubber gloves and boots.
• ELECTRIC ENERGY HAZARD. Do not attempt to alter any UPS or battery wiring or connectors.
Attempting to alter wiring can cause injury.
• Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It may be
toxic.
• The UPS unit is not suitable for IT or corner-earthed power distribution systems.
• Installation or servicing should be performed by qualified service personnel knowledgeable of
UPS and battery systems, and required precautions. Keep unauthorised personnel away from
equipment. Consider all warnings, cautions, and notes before installing or servicing equipment.
DO NOT DISCONNECT the batteries while the UPS is in Battery mode.
CAUTION

Safety Warnings
2-2 Eaton 9E UPS (80-200 kVA, 380/400/415V) Installation and Operation Manual
• See installation instructions before connecting to the supply.
• Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according
to the instructions.
• Replace batteries with the same number and type of batteries as originally installed with the
UPS.
• Disconnect the charging source prior to connecting or disconnecting terminals.
• Determine if the battery is inadvertently grounded. If it is, remove the source of the ground.
Contacting any part of a grounded battery can cause a risk of electric shock. An electric shock is
less likely if you disconnect the grounding connection before you work on the batteries.
• Proper disposal of batteries is required. Refer to local codes for disposal requirements.
• Do not dispose of batteries in a fire. Batteries may explode when exposed to flame.
• Keep the UPS door closed and front panels installed to ensure proper cooling airflow and to
protect personnel from dangerous voltages inside the unit.
• Do not install or operate the UPS system close to gas or electric heat sources.
• The operating environment should be maintained within the parameters stated in this manual.
• Keep surroundings uncluttered, clean, and free from excess moisture.
• Observe all DANGER, CAUTION, and WARNING notices affixed to the inside and outside of the
equipment.
AVERTISSEMENT!
• Les batteries peuvent présenter un risque de décharge électrique ou de brûlure par des courts–
circuits de haute intensité. Prendre les précautions nécessaires.
• Pour le replacement, utiliser le même nombre et modéle des batteries.
ATTENTION!
CAUTION
• Une mise au rebut réglementaire des batteries est obligatoire. Consulter les règlements en
vigueur dans votre localité.
• Ne jamais jeter les batteries au feu. L'exposition aux flammes risque de les faire exploser.
The product has the CE marking in compliance with the following European directives:
LVD Directive (Safety) 2006/95/EEC
EMC Directive 2004/108/EEC
This product is designed for commercial and industrial applications. In a residential environment, the
product may cause radio interference , in which the user may be required to take additional measures.
CE marking