EAW KF695z User manual

SPECIFICATIONS KF695z
FEATURES
One Main Street, Whitinsville, MA 01588 508 234 6158 Toll Free 800 992 5013 FAX [phone] [e-mail] www.eaw.com
EAW products are continually improved. All specifications are therefore subject to change without notice. KF695z/2 pp October 2001 Printed in USA
• Compact Virtual Array™ three-way system
• Vented, LF horn-loaded MF/HF (90° x 45° coverage pattern)
• 15-in LF,10-in MF, 3-in voice coil/1.4-in exit HF
• Switchable powering: Tri-amp or Bi-amp
(passive LF/MF)
• For portable use or permanent installation
A 3-way full range system in a vented trapezoidal enclosure.
Includes a 15-in woofer, vented, a horn-loaded 10-in
midrange cone and a 1.4-in exit compression driver on a 90°
x 45° constant directivity horn. Powering mode is switchable:
bi-amplified (passive LF/MF crossover) or tri-amplified.
The KF695z Virtual Array™ system’s true 3-way design dra-
matically improves the quality of vocal reproduction while its
cone-driven midrange horn extends pattern control into the
lower octaves. Universal suspension hardware (flytrack with
integral 3/8"-16 mounting point) supports permanent or
portable applications. Six year warranty.
Applications include:
Concert Tours
Band PA Ballroom Events
Corporate Events Convention Centers
Large Houses of Worship Live Music Club
DESCRIPTION
APPLICATION
PERFORMANCE
PHYSICAL
Calculated Maximum Output (dB SPL @ 1m)
Bi-amped LF/MF Peak 134.5
LF Peak 134.5
MF Peak 141.0
HF Peak 138.0
Bi-amped LF/MF Long Term 128.5
LF Long Term 128.5
MF Long Term 135.0
HF Long Term 132.0
Nominal Coverage Angle, -6 dB Points (degrees)
Horizontal 90
Vertical 45
LF Subsystem 1x 15-in, vented
MF Subsystem 1x 10-in horn-loaded cone
HF Subsystem 1x 1.4-in exit compression driver
on constant directivity horn
Configuration 3-way, full fange
Powering Switchable: bi-amplified (passive
LF/MF crossover) or tri-amplified
Controls (switches, knobs) Powering mode switch
Cabinet Type (shape) Trapezoidal
Enclosure Materials Baltic birch plywood
Finish Wear-resistant textured black
paint
Connectors 2x Neutrik NL4 Speakon
2x Neutrik NL8 Speakon
Suspension Hardware (6) 3-position flytracks with
integral 3/8”-16 threaded mount
ing points (3 each top and bottom)
Grille Powder coated perforated steel,
foam backed
Frequency Response (Hz)
±3 db 65 Hz to 17 kHz
-10 dB 50 Hz
Axial Sensitivity (dB SPL, 1 Watt @1m)
Bi-amped LF/MF 100
LF 100
MF 109
HF 110
Impedance (Ohms)
Bi-amped LF/MF 8
LF 8
MF 8
HF 8
Power Handling, (Watts Continuous)
Bi-amped LF/MF 700
LF 700
MF 400
HF 160
Recommended High-Pass Frequency
24 dB/Octave 50 Hz

SPECIFICATIONS KF695z
DIMENSIONAL DRAWING A & E SPECIFICATIONS
One Main Street, Whitinsville, MA 01588 508 234 6158 Toll Free 800 992 5013 FAX [phone] [e-mail] www.eaw.com
EAW products are continually improved. All specifications are therefore subject to change without notice. KF695z/2 pp October 2001 Printed in USA
.
1. SYMBOL INDICATES 3.00 X 1.35 FLYTRACK.
2. SYMBOL INDICATES MOUNTING POINT,
3/8-1 THREADED HOLE (FLYTRACK)
3. SYMBOL INDICATES CENTER OF BALANCE.
A
A
L
C
5.94
14.25
10.00
(12.81)
20. 2
20°
12.25
TOP
DIMENSIONS APPLY
TO TOP & BOTTOM
FRONT
GRILLE PARTIALLY SHOWN
19.75 T.S.C.
33.25
.05
VIEW A-A
DIMENSIONS APPLY
TO BOTH SIDES
14.58
8.25 2X .44
4X HANDLE
2.13
28.98
2X 8.75
22.42
C
L
10.08
BACK
1 .75
4.50
2.13
ACCESS PANEL
28.98
INPUT
8.00
509098 (1)
6/19/01
Manufacturing tolerances are +/- 0.13 and +/- 1°
Dimensions Inches Millimeters
Height 33.3 845
Width (front) 19.8 502
Width (rear) 12.9 328
Depth 20.6 524
Trapezoid Angle 10 Degrees per Side
Weights Pounds Kilograms
Net Weight 135.0 61.4
Shipping Weight 142.0 64.6
The three-way full range loudspeaker system shall incorporate
a 15-in LF transducer, a 10-in cone MF transducer and a 1.4-
in exit compression driver HF transducer.
The LF driver shall be mounted in a vented enclosure tuned
for optimum low frequency response. The MF driver shall be
loaded into a midrange horn constructed of 3mm birch ply-
wood reinforced with high density polyurethane foam. The MF
horn shall incorporate a phase/displacement plug. The HF
driver shall be loaded on a constant directivity horn with a
nominal coverage pattern of 90° (h) x 45° (v). An internal
passive filter network shall provide system equalization and
fourth order acoustical crossover between the low and mid
frequency sections in bi-amped mode .
System frequency response shall vary no more than ±3 dB
from 65 Hz to 17 kHz measured on axis. In bi-amped mode,
the low/mid section shall produce a Sound Pressure Level
(SPL) of 100 dB SPL on axis at 1 meter with a power input of
1 Watt, and shall be capable of producing a peak output of
134.5 SPL on axis at 1 meter. It shall handle 700 Watts of
amplifier power (continuous) and shall have a nominal
impedance of 8 Ohms. The HF section shall produce a Sound
Pressure Level (SPL) of 110 dB SPL on axis at 1 meter with a
power input of 1 Watt, and shall be capable of producing a
peak output of 138 SPL on axis at 1 meter. It shall handle 160
Watts of amplifier power (continuous) and shall have a nom-
inal impedance of 8 Ohms.
In tri-amped mode, the low frequency and high frequency sec-
tions shall meet all bi-amped mode performance criteria. In
addition, the midrange frequency section in tri-amped mode
shall produce a Sound Pressure Level (SPL) of 109 dB SPL on
axis at 1 meter with a power input of 1 Watt, and shall be
capable of producing a peak output of 141 SPL on axis at 1
meter. It shall handle 400 Watts of amplifier power (continu-
ous) and shall have a nominal impedance of 8 Ohms.
The loudspeaker enclosure shall be trapezoidal in shape. It
shall be constructed of multi-ply, void-free cross-grain-lami-
nated Baltic birch plywood and shall employ extensive inter-
nal bracing. It shall be finished in wear-resistant textured
black paint. Input connectors shall be 2x Neutrik NL4
Speakon and 2 x Neutrik NL8 Speakon. The system shall
include a switch allowing it to be operated in bi-amp or tri-
amp powering mode. A total of six 3-position flytracks with
integral 3/8"-16 threaded mounting point (3 each top and
bottom) shall be provided. The front of the loudspeaker shall
be covered with a powder coated perforated steel grille
backed with open cell foam to protect against dust.
The three-way full range loudspeaker shall be the EAW model
KF695z.
PHYSICAL continued