Echo Rapid Loader 99944200610 User manual

PAS RAPID LOADERTM TRIMMER ATTACHMENT
OPERATOR'SMANUAL 1
PAS Rapid LoaderTM Trimmer Attachment
Operator'sManual
MODEL 99944200610
FOR MODELS: SRM-2100SB TYPE 1/1E
SRM-2400SB TYPE 1/1E
SRM-210SB/211SB
SRM-260SB/261SB
PAS-2100 TYPE 1E
PAS-2400 TYPE 1E
PAS-2601 TYPE 1E
PAS-210/211
PAS-230/231
PAS-260/261
WARNING DANGER
Readrulesforsafeoperationandinstructionscarefully.ECHOprovidesanOperator's
ManualandaSafetyManual,withyouroriginalSplitBoom/ProAttachmentSeriesTM
Trimmer.Thosemanualsandthismanualmustbereadandunderstoodforproperand
safeoperation.
X7702273502 X770000332
01/06

2
Copyright©2006ByEcho,Incorporated
All Rights Reserved.
TABLE OF CONTENTS
Introduction ...............................................................2
- The Operator's Manual .......................................2
- The Safety Manual .............................................2
Safety .........................................................................3
- Manual Safety Symbols and Important
Information .........................................................3
- InternationalSymbols .........................................3
- Personal Condition and Safety Equipment .........3
- Equipment ...........................................................6
Description ................................................................6
Contents ....................................................................7
Assembly ...................................................................7
- PowerHeadShaft/AttachmentLower
Shaft Assembly ..................................................7
- PlasticShieldInstallation....................................8
- NylonLineHead Installation ..............................9
Operation ...................................................................9
Maintenance ............................................................ 10
- SkillLevels ........................................................ 10
- Maintenance Intervals ...................................... 10
- Lubrication........................................................ 10
- NylonLineReplacement ................................... 11
Storage..................................................................... 12
Specifications........................................................... 12
ServicingInformation............................................... 16
- Parts/SerialNumber .......................................... 16
- Service .............................................................. 16
- ECHOConsumer ProductSupport.................... 16
- Warranty Card .................................................. 16
- Additional or Replacement Manuals ................ 16
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job
dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will
find both easy to use and full of helpful operating tips and SAFETY messages.
THE OPERATOR'SMANUAL
Read and understand this manual before operation. Keep it in a safe
place for future reference. It contains specifications and information for
operation and maintenance specific to the attachment.
THE SAFETY MANUAL
Explains possible hazards and what measures you should take to insure
safe operation.
Specifications,descriptionsandillustrativematerialin
this literature are as accurate as known at the time of
publication, but are subject to change without notice.
Illustrations may include optional equipment and
accessories, and may not include all standard equipment.

PAS RAPID LOADERTM TRIMMER ATTACHMENT
OPERATOR'SMANUAL 3
Symbol
description/application Symbol form/shape Symbol
description/application
Symbol form/shape
Hot
Surface
Carburetor adjustment
- Idle speed
Carburetor adjustment
- High speed mixture
Symbol
description/application Symbol form/shape Symbol
description/application
Symbol form/shape
Read and understand
Operator's Manual.
Wear eyes, ears and
head protection Emergency stop
Fuel and oil mixture
Finger Severing
Carburetor adjustment
- Low speed mixture
Safety/Alert
Avoidallpower
lines.This unitis
notinsulated
againstelectrical
current.
Do not operate
closerthan 15M
(50 ft.) from
electrical
hazards.
Keepbystanders
atleast15meters
(50feet)away.
Planretreatpath
from falling
objects.
Wear hand
protection.Use
twohanded.
DONOTsmoke
nearfuel.
DONOTallow
flamesorsparks
nearfuel.
Wear slip
resistantfoot
wear.
Ignition
ON/OFF
Primerbulb
Keep bystanders and helpers
away 15 m (50 ft.).
Choke Control
"Cold Start"
Position
(ChokeClosed)
Choke Control
"Run"
Position
(ChokeOpen)
INTERNATIONALSYMBOLS
IMPORTANT Theenclosedmessage
provides information necessary for the
protection of the unit.
NOTE Thisenclosedmessageprovidestipsfor
use, care and maintenance of the unit.
This symbol accompanied by the words WARNING and
DANGER calls attention to an act or condition that can lead
to serious personal injury to operator and bystanders.
The circle with the slash symbol means whatever is shown
within the circle is prohibited.
SAFETY
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety
alerts and helpful, information messages preceded by symbols or key
words. The following is an explanation of those symbols and key words
and what they mean to you.
IMPORTANT
NOTE
PERSONAL CONDITION AND SAFETY EQUIPMENT
WARNING DANGER
Trimmer/Brush Cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly
or safety precautions are not followed. Proper clothing and safety gear must be worn when operating a
trimmer/brushcutter.

4
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
•ifyouaretakingmedication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE requirements whenever you operate the trimmer.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your grip on the Trimmer/Brush Cutter handles. Gloves also reduce the
transmission of machine vibration to your hands.
Hearing Protection
ECHO recommends wearing hearing protection whenever unit is used.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DONOTWEARSHORTS,
• DONOTWEARTIES,SCARVES,JEWELRY.
Wear sturdy work shoes with non-skid soles;
• DONOTWEAROPENTOEDSHOES,
• DONOTOPERATEUNITBAREFOOTED.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue which may lead to heat stroke. Schedule heavy work for early
morning or late afternoon hours when temperatures are cooler.
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals, may be
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning
sensations, followed by loss of color and numbness in the fingers. The following precautions are strongly recommended,
becausetheminimum exposure which might trigger the ailment is unknown.
• Keep your body warm, especially the head, neck, feet, ankles,
hands, and wrists.
• Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks, and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the trimmer or other hand-held power equipment is not
required.
• If you experience discomfort, redness and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.

PAS RAPID LOADERTM TRIMMER ATTACHMENT
OPERATOR'SMANUAL 5
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness,
swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high
riskfordevelopingaRepetitiveStress Injury(RSI).An extremeRSIcondition isCarpalTunnel Syndrome(CTS),which
could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged
exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended, or twisted position.
Instead, try to maintain a straight wrist position. Also, when grasp-
ing, use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive
movement.
• Do exercises to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if
you feel tingling, numbness, or pain in the fingers, hands, wrists, or
arms. The sooner RSI/CTS is diagnosed, the more likely permanent
nerve and muscle damage can be prevented.
WARNING DANGER
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can cause
serious injury or death.
ReadtheManuals
• Provide all users of this equipment with the Operator's Manual and
Safety Manual for instructions on Safe Operation.
CleartheWorkArea
• Spectators and fellow workers must be warned, and children and
animalspreventedfrom coming nearer than15m(50 ft.) whiletheunit
is in use.
KeepaFirmGrip
• Hold the front and rear handles with both hands, with thumbs and
fingers tightly encircling the handles.
KeepaSolidStance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not over reach.
AvoidHotSurfaces
• During operation, the drive shaft housing, attachment bearing
housing and muffler cover area may become very hot, too hot to
touch. Avoid contact during and immediately after operation.

6
5
12
3
4
P/N 89016054130
DESCRIPTION
Locate this safety decal on your attachment. Make sure the decal is legible and that you understand and follow the
instructions on it. If it cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING
instructionsfor specific information.
1. LOWERDRIVESHAFTASSEMBLY-IncludestheDebrisShieldAssembly,GearHousingassembly,FlexibleDrive
Cable, Rapid LoaderTM Head and Safety Decals.
2. FLEXIBLEDRIVECABLE-Cableendfitsintoupperdriveshaftcoupler.Lubricatedrivecableevery25hourswith
ECHO®LUBETM grease.
3. PLASTICDEBRISSHIELDASSEMBLY-Includedinplasticbag(co-pack).MUSTbeinstalledonunitbeforeuse,
see Assembly Instructions. Shield assembly includes the Cut-Off Knife. Mounts on the Gear Housing Assembly
just above the cutting attachment. Helps protect the operator by deflecting debris produced during the trimming
operation. This shield must be replaced with the steel shield for blade use.
4. CUT-OFFKNIFE-Trimslinetothecorrectlength.
5. RAPIDLOADERTM HEAD-Containsreplaceablenylontrimminglines.
EQUIPMENT
Before operation a complete check of the unit must be performed;
• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.
• Inspect shield for damage and ensure that cut-off knife is securely in place. Replace if shield is damaged or missing.
• Check that the cutting attachment is firmly attached and in safe operating condition.
• Check that front loop handle and shoulder strap/ or shoulder/waist harness are adjusted for safe, comfortable operation.
See Assembly Section for proper adjustment.

PAS RAPID LOADERTM TRIMMER ATTACHMENT
OPERATOR'SMANUAL 7
CONTENTS
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.
__ 1 - ProAttachmentSeriesTM TrimmerAttachment
__ 1 - Operator's Manual
__ 1 - Safety Manual
__ 1 - Warranty Registration Card
__ 2 - LockingTools
__ 1 - Wrench17x14.5
__ 1 - Rapid LoaderTM Head
__ 1 - Nut
__ 1 - Washer10x32x1.2
__ 1 - PlasticDebrisShield
__ 1 - SplitPin
__ 1 - Shieldplate
__ 3 - 5mmx16mmScrews(shieldmounting)
__ 1 - Storage Hook Assembly
ASSEMBLY
WARNING DANGER
Do not perform maintenance or assembly procedures with engine
running.
Tools Required: Screwdriver,HeadLockingTool,17x14.5mmWrench,
NeedleNose Pliers
Parts Required: Power Head Shaft, Attachment Lower Shaft
Assembly,PlasticShield,ShieldPlate,three(3)
5mmx16mmscrews,RapidLoaderTM Head
POWER HEAD SHAFT/ATTACHMENT LOWER SHAFT ASSEMBLY
1. Set Power Head/Shaft Assembly on a level surface.
2. Pull locator pin (A) and rotate counter clockwise 1/4 turn to lock
out position.
3. Remove vinyl cap from attachment drive shaft.
4. Remove cardboard spacer, if necessary.
5. Carefully fit attachment lower drive shaft assembly into coupler (B)
to decal assembly line (C), making sure that the inner lower drive
shaft engages into the upper drive shaft mount.
A
B
D

8
PLASTIC SHIELD INSTALLATION
(for Nylon Line Operation)
NOTE
The plastic shield is for use with the Nylon Line Head only.
Install Metal Shield when using plastic or metal blades.
1. Remove plastic threaded shaft sleeve and adapter plate (C) from
PTO shaft (A).
2. Place the shield on the bottom of the bearing housing flange.
3. Place shield plate (B) on shield, align holes. Install three (3) screws
from bottom through plate and shield into gear case.
4. Assemble upper plate (C) onto PTO shaft.
C
E
D
6. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft
hole. Insure locator pin is fully engaged by gently twistinglower
drive shaft. Locator pin (A) should snap flush in coupler. Full
engagement will prevent further shaft rotation.
7. Secure lower shaft assembly to coupler by tightening clamping
knob(D).
NOTE
Earlier model Power Heads may have shorter couplings. Short
couplings fit flush to decal point (E). New couplings are 4-3/4 in.
long, and fit flush to line (C).
NOTE
Lower bearing housing and head assembly must be in line with the
engine.
ABC
A

PAS RAPID LOADERTM TRIMMER ATTACHMENT
OPERATOR'SMANUAL 9
NYLON LINE HEAD INSTALLATION
1. Align hole in upper plate with notch in edge of gear housing and
insert head locking tool (A). Remove plastic sleeve from PTO shaft.
2. Be sure upper plate (B) remains on PTO shaft.
3. Place line head onto PTO shaft, followed by large metal washer (C).
4. Thread L.H. nut (D) on PTO shaft. Tighten securely.
5. Installnewsplit pin(E).
6. Removelockingtool(A).
OPERATION
NOTE
Refer to your Split Boom\Pro Attachment SeriesTM Operator's Manual for correct engine fueling, starting and stopping
instructions.
IMPORTANT
Never wear line shorter than 1-1/2 inch extension from head, otherwise overspeeding and engine damage may result.
C

10
MAINTENANCE
Your ECHO trimmer is designed to provide many hours of trouble free service. Regular scheduled maintenance will help
your trimmer achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your
unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the
ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your ECHO dealer for repairs.
SKILL LEVELS
Level1= Easy to do. Most required tools come with unit.
Level2= Moderate difficulty. Some specialized tools may be required.
Level3= Experiencerequired.Specializedtoolsarerequired.
MAINTENANCE INTERVALS
Component/System Maintenance Procedure Skill Level Frequency
DriveShaft Grease 1 Every25hoursofuse
GearHousing Grease 1 Every50hoursofuse
Screws/Nuts/Bolts Inspect/Tighten/Replace 1 Beforeeachuse
LUBRICATION
Level1.
Tools Required: 8mmOpenEndWrench,Screwdriver,CleanRag.
Parts Required: ECHO®LUBETM 8oz.(P/N91014)orLithiumBase
Grease.
Gear Housing
1. Cleanallloosedebris fromgearbox.
2. Remove plug (A) and check level of grease.
3. Fill gear case with grease.
4. Install plug (A).
Drive Shaft (Lower)
IMPORTANT
Lower and upper drive shaft must be lubricated with ECHO®
LUBETM grease every 25 hours of operation, otherwise drive shaft
assembly overheating and failure can result.
A

PAS RAPID LOADERTM TRIMMER ATTACHMENT
OPERATOR'SMANUAL 11
1. Insert pre-cut204mm(8in.) length of nylon cuttingline(recom-
mendedsizes2.4mm [.095in.]to3.9mm[.155in.])throughoutside
openingsoftrimmerhead.Minimumof153mm(6in.)oflineshould
extendfromeachopening.3.9mm[.155in.]linenot
recommendedfortrimmersunder26cc.
NOTE
Insert cutting line ends to center of head recess to insure easy
removal of used lines.
NOTICE:
Nylon line can damage plastic shield. When installing line seg-
ments, make sure line does not curve upward toward shield.
1. Loosen two (2) 8 mm upper gear housing bolts (B) and locator
screw (C). Remove gear case assembly.
2. Remove flex cable, wipe clean and apply a thincoating15ml,of
grease.
3. Install flex cable. Make sure cable end engages upper drive shaft
adaptor.
4. Install gear case assembly onto drive shaft aligning locator screw
with hole in drive shaft.
5. Tighten two 8 mm bolts (B) andlocatorscrew (C).
B
C
NYLON LINE REPLACEMENT
Level1.
Tools Required: None
Parts Required: Pre-cut Nylon Line
IMPORTANT
Flat edge of washers (D) must be against drive shaft.
D
MODELS REQUIREDLINESIZES
SRM-2100SB
SRM-210SB/211SB .080 - .095 in.
PAS-210/211
PAS-230/231
SRM-2400SB .095 - .130 in.
SRM-260SB/261SB .095 - .155 in.
PAS-2601 .095 - .155 in.
PAS-260/261 .095 - .155 in.

12
SPECIFICATIONS
PAS Rapid LoaderTM Attachment
NOTE Install and use U-Handle when operating any model with blade.
Shaft Length ------------------------------------------------ 838mm(33in.)
Attachment Width -----------------------------------------178mm(7in.)
Attchment Height------------------------------------------229mm(9in.)
Weight (dry) w/blade--------------------------------------1.36kg.(3.1lb.)
DriveShaft --------------------------------------------------6.35mm(1/4in.)FlexShaft
RotatingDirection -----------------------------------------Counter-clockwiseviewed from the top
Cutter Head ------------------------------------------------- RapidLoaderTM head(2-lines)with.095CrossFireTM Line
STORAGE
Storage Hook Installation
1. Insert small end of hook into locating hole on attachment shaft.
2. Slide plastic cap onto end of attachment shaft.

PAS RAPID LOADERTM TRIMMER ATTACHMENT
OPERATOR'SMANUAL 13
NOTES

14
NOTES

PAS RAPID LOADERTM TRIMMER ATTACHMENT
OPERATOR'SMANUAL 15
NOTES

DEALER?
Call
1-800-432-ECHO
or
www.echo-usa.com
ECHO,INCORPORATED
400 OAKWOOD ROAD
LAKE ZURICH, IL 60047
www.echo-usa.com
CONSUMER PRODUCT
SUPPORT
1-800-673-1558
8:30 - 4:30 Mon - Fri C.S.T.
001001/999999
SERVICINGINFORMATION
PARTS/SERIAL NUMBER
GenuineECHOPartsandECHOREPOWER™PartsandAssembliesfor
yourECHOproducts areavailableonlyfrom anAuthorizedECHO
Dealer. When you do need to buy parts always have the Model
Number and Serial Number of the attachment with you. You can find
these numbers on the driveshaft model/serial number label. For future
reference, write them in the space provided below.
Model No. ____________SN.__________
SERVICE
Service of this product during the warranty period must be performed
by an Authorized ECHO Service Dealer. For the name and address of
the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO(3246). WhenpresentingyourunitforWarranty
service/repairs, proof of purchase is required.
ECHO CONSUMER PRODUCT SUPPORT
If you require assistance or have questions concerning the application,
operation or maintenance of this product you may call the ECHO
ConsumerProductSupportDepartmentat1-800-673-1558from8:30am
to4:30pm (Central Standard Time)MondaythroughFriday. Before
calling, please know the model and serial number of your unit to help
your Consumer Product Support Representative.
WARRANTY CARD
This card is our means of registering all original owners of ECHO
equipment. The card plus proof of purchase provides you the assur-
ance that authorized warranty work will be done. It also provides a
direct link between you and ECHO if we find it necessary to contact
you.
ADDITIONAL OR REPLACEMENT MANUALS
SafetyManuals inEnglish/Spanish orEnglish/Frenchareavailable, freeofcharge, fromyourECHOdealer orat
www.echo-usa.com.
Operator'sandPartsManualsareavailableby:
• Downloadingfreefromwww.echo-usa.com
• Purchasingfromyour EchoDealer.
• Manuals are available by sending a written request stating the model number and serial number of your Echo unit,
part number of the manual, your name and address, and mail to the address below.
SafetyVideosareavailablefrom your Echo dealer. A$5.00shippingchargewill be required foreachvideo.