Echo SHC-260 User manual

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 1
WARNING DANGER
Readrulesforsafeoperationandinstructionscarefully. ECHOprovidesanOperator's
ManualandaSafetyManual. Bothmustbereadandunderstoodforproperandsafe
operation.Failuretodosocouldresultinserousinjury.
Shaft Hedge Clipper
Operator'sManual
MODEL SHC-260
Serial Number 06001001 - 06999999
X753001620
01/04
X7532094900

2
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job
dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will
find both easy to use and full of helpful operating tips and SAFETY messages.
THE OPERATOR'SMANUAL
Read and understand this manual before operation. Keep it in a safe
place for future reference. It contains specifications and information for
operation, starting, stopping, maintenance, storage, and assembly
specific to this product.
THE SAFETY MANUAL
Read and understand this manual before operation. Keep it in a safe
place for future reference. It explains possible hazards involved with the
use of Hedge Clippers and what measures you should take to make their
use safer.
- StartingColdEngine ................................................. 15
- StartingWarmEngine ............................................... 16
- StoppingEngine ........................................................ 16
- HedgeTrimming ....................................................... 17
Maintenance ..................................................................... 17
- SkillLevels................................................................ 17
- Maintenance Intervals .............................................. 18
- Air Filter ................................................................... 19
- Fuel Filter ................................................................. 19
- SparkPlug................................................................. 20
- CoolingSystemCleaning .......................................... 20
- Exhaust System ........................................................ 21
- Carburetor Adjustment............................................. 22
- Lubrication................................................................ 23
- SharpeningBlades..................................................... 25
- Blade Adjustment ..................................................... 25
Troubleshooting................................................................ 26
Storage .............................................................................. 27
ServicingInformation........................................................ 28
- Parts.......................................................................... 28
- Service ....................................................................... 28
- ECHO Consumer Product Support.......................... 28
- Warranty Card .......................................................... 28
- Additional or Replacement Manuals ........................ 28
Specifications, descriptions and illustrative material in this
literature are as accurate as known at the time of publication,
but are subject to change without notice. Illustrations may
include optional equipment and accessories, and may not
include all standard equipment.
Copyright© 2004 By Echo, Incorporated
All Rights Reserved.
TABLE OF CONTENTS
Introduction ........................................................................ 2
- The Operator's Manual .............................................. 2
- The Safety manual ...................................................... 2
Manual Safety Symbols and Important Information ......... 3
Safety.................................................................................. 3
- Decals ......................................................................... 3
- International Symbols................................................. 4
Safety Instructions ....................................................5
- Personal Conditions and Safety Equipment .......5
- ExtendedOperation/ExtremeConditions ............5
- Equipment ...........................................................6
- SafeOperation ....................................................7
EmissionsControl ......................................................7
Description ................................................................8
- Contents .............................................................8
Specifications.................................................................... 11
Assembly.......................................................................... 12
- Gear Housing Assembly / Drive Shaft ..................... 12
- Drive Shaft Assembly / Power Head........................ 12
- Throttle Linkage and Ignition Leads ......................... 13
Pre-Operation ................................................................... 14
- Fuel ........................................................................... 15
Operation.......................................................................... 15

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 3
SAFETY
DECALS
Locate these safety decals on your unit. Make sure the decals are
legible and that you understand and follow the instructions on them.
If a decal cannot be read, a new one can be ordered from your ECHO
dealer. SeePARTSORDERINGinstructionsforspecificinformation.
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety
alerts and helpful, informational messages preceded by symbols or key
words. The following is an explanation of those symbols and key
words and what they mean to you.
This symbol accompanied by the words WARNING
and DANGER calls attention to an act or condition that
can lead to serious personal injury to operator and
bystanders.
The circle with the slash symbol means whatever is
shown within the circle is prohibited.
IMPORTANT
The enclosed message provides
information necessary for the protection
of the unit.
NOTE
This enclosed message provides tips for
use, care and maintenance of the unit.
IMPORTANT
NOTE
WARNING DANGER
This unit is not designed to insulate against hazards associated with the contact of wires
carrying electrical current.
To avoid possible injury/death due to electrical shock or other hazards. DO NOT operate unit if
any wires (power, telephone, cable, etc.) are closer than 15 feet (4/5 meters minimum distance,
to any part of the unit or operator.
WARNING DANGER
This unit can be dangerous if used improperly. • Falling objects and/or blade
contact can cause serious injury to operator, helpers and bystanders. • Keep
helpers and bystanders at least 50 feet (15m) clear of operating area. • To reduce
injury risk, READ AND UNDERSTAND the operator's Manual, replacement copies
are available through your ECHO dealer. • Wear Protective clothing (head, hearing
and eye protection meeting ANSI standards) specified in the Operator's Manual.
• STOP engine before making repairs or blade adjustments. • Keep hand away from
blade. P/N 89018721460
P/N 89016006361
Hot Surface Decal

4
Shaft Decal
Spanish Decal
WARNING DANGER
Thisunitcanbedangerous
and cause serious injury if
improperlyused.Toreduce
injury risk to operator,
helpers and bystanders,
read and understand the
Operator's and Safety
Manuals,whichareprovided
in Spanish.
ADVERTENCIA PELIGRO
English Translation
Estaunidad
puedeser
peligrosay
producirlesiones
personales
gravessinose
usaenformaadecuada.Para
reducirelriesgo de
lesionarse,losoperadores,
los ayudantes y los
espectadoresdebenleery
comprenderelManualDel
OperadorylosManuales De
Seguridadqueseentregan
escritos en español.
INTERNATIONALSYMBOLS
SYMBOL
DESCRIPTION/APPLICATION SYMBOL FORM/
SHAPE SYMBOL
DESCRIPTION/APPLICATION
SYMBOL FORM/
SHAPE
Hot
Surface
Carburetor
adjustment
-Idlespeed
Carburetor
adjustment
- High speed
mixture
SYMBOL
DESCRIPTION/APPLICATION SYMBOL FORM/
SHAPE SYMBOL
DESCRIPTION/APPLICATION
SYMBOL FORM/
SHAPE
Readand
understand
Operator'sManual.
Weareyes,ears
andhead
protection
Emergencystop
Fueland oil
mixture
FingerSevering
Carburetor
adjustment
-Low speed
mixture
Safety/Alert
Do not operate
closerthan 15M
(50 ft.) from
electrical
hazards.
Keepbystanders
atleast15meters
(50feet)away.
Planretreatpath
from falling
objects.
Wearhand
protection.Use
twohanded.
DONOTsmoke
nearfuel.
DONOT allow
flamesorsparks
nearfuel.
Wearslip
resistantfoot
wear.
Ignition
ON/OFF
Primerbulb
Avoidallpower
lines.This unitis
notinsulated
againstelectrical
current.
CHOKE CONTROL
"COLD START"
POSITION
(CHOKE CLOSED)
CHOKE CONTROL
"RUN"
POSITION
(CHOKEOPEN)
P/N 89016021560

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 5
SAFETYINSTRUCTIONS
PERSONAL CONDITION AND SAFETY EQUIPMENT
WARNING DANGER
Hedge Clipper users risk injury to themselves and others if the hedge clipper is used improperly and or safety
precautions are not followed. Proper clothing and safety gear must be worn when operating a hedge clipper.
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• ifyouaretakingmedication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Eyeprotectionthat meets ANSI Z87.1orCE requirements
must be worn whenever you operate the unit.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your
grip on the handles. Gloves also reduce the transmission
of machine vibration to your hands.
Hearing Protection
Wearhearingprotection.ECHOrecommendswearing
hearing protection whenever unit is used.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DONOTWEARSHORTS,
• DONOTWEARTIES,SCARFS,JEWELRY.
Wear protective hair covering to contain long hair.
Wear sturdy work shoes with nonskid soles;
• DONOTWEAROPENTOEDSHOES,
• DONOTOPERATEUNITBAREFOOTED.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue
which may lead to heat stroke. Schedule heavy work for
early morning or late afternoon hours when temperatures
arecooler.
EXTENDED OPERATION/EXTREME CONDITIONS
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon, which
affects the fingers of certain individuals, may be brought about by
exposure to vibration and cold. Exposure to vibration and cold may
cause tingling and burning sensations, followed by loss of color and
numbness in the fingers. The following precautions are strongly
recommended,becausethe minimumexposurewhich mighttriggerthe
ailmentisunknown.
• Keep your body warm, especially the head, neck, feet, ankles, hands,
and wrists.
• Maintain good blood circulation by performing vigorous armexercises
during frequent work breaks, and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the unit or other hand-held power equipment is not
required.
• If you experience discomfort, redness, and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.

6
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers,
hands, arms, and shoulders may cause soreness, swelling, numbness,
weakness, and extreme pain in those areas. Certain repetitive hand
activities may put you at a high risk for developing a Repetitive Stress
Injury(RSI).AnextremeRSIconditionisCarpalTunnelSyndrome
(CTS), which could occur when your wrist swells and squeezes a vital
nerve that runs through the area. Some believe that prolonged exposure
to vibration may contribute to CTS. CTS can cause severe pain for
months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended, or twisted position.
Instead try to maintain a straight wrist position. Also, when grasping,
use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive move-
ment.
• Do exercises to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if
you feel tingling, numbness, or pain in the fingers, hands, wrists, or
arms. The sooner RSI/CTS is diagnosed, the more likely permanent
nerve and muscle damage can be prevented.
EQUIPMENT
WARNING DANGER
Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment
combination. Read and comply with all safety instructions listed in this manual and safety manual.
• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or
replace as needed.
• Inspect fuel lines, tank and area around carburetor for fuel leaks. DO
NOT operate unit if leaks are found.
• Never adjust blades when the engine is operating.
• Inspect hand guard for damage. Replace if damaged or missing.
• Check that the blade assembly is firmly attached and in safe operating
condition. Dull, loose or damaged blades should not be used.
• ECHO, INC. will not be responsible for the failure of cutting devices
or accessories which have not been tested and approved by ECHO
for use with this unit.

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 7
SAFE OPERATION
WARNING DANGER
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can cause
serious injury or death.
ReadtheManuals
• Provide all users of this equipment with the Operator's Manual and
Safety Manual for instructions on Safe Operation.
CleartheWorkArea
• Spectators and fellow workers must be warned, and children and
animalspreventedfrom coming nearerthan15 m (50ft.)while the unit
is in use.
KeepaFirmGrip
• Hold the front and rear handles with both hands, with thumbs and
fingers tightly encircling the handles.
KeepaSolidStance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not over reach.
AvoidHotSurfaces
• Keep exhaust area clear of flammable debris. Avoid contact during
andimmediatelyafteroperation.
EmissionControlLabel (locatedonEngine) (EXAMPLEONLY,informationonlabelvariesbyFAMILY).
PRODUCT EMISSION DURABILITY
The 300 hour emission durability compliance period is the time span selected by the manufacturer certifying the
engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are
followed as listed in the Maintenance Section of this manual.
IMPORTANTENGINEINFORMATION
ENGINE FAMILY: 4EHXS.0254KA DISPLACEMENT: 25.4 CC
EMISSIONCOMPLIANCEPERIOD :300HRS.
THISENGINE MEETS U.S. EPAPH2 AND 2000 ANDLATER
CALIFORNIAEMISSIONREGULATIONS FOR S.O.R.E. REFER TO
OWNER'S MANUAL FOR MAINTENANCE SPECIFICATIONS AND
ADJUSTMENTS.
EMISSION CONTROL
EPA Phase 2
The emission control system for this engine is EM/TWC (Engine
ModificationwithCatalyst).

8
DISCRIPTION
The ECHO product you have purchased has been factory pre-assembled for your convenience. Due to packaging
restrictions, some assembly of the SHC-260 is required.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.
CONTENTS LIST
__ 1- PowerHead
__ 1 - Gear Case Assembly
__ 1 - Drive Shaft Assembly
__ 1 - Operator's Manual
__ 1 - Hedge Clipper Safety Manual
__ 1 - Warranty Statement
__ 1 - Warranty Registration Card
__ 1-BladeCover
__ 1 -Echo Power Blend TM 2-strokeoilsample
__ 1-T-Wrench17x19
__ 1-4mmHexWrench
__ 1-8x10mmWrench
__ 1 - Safety Glasses

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 9
13
14
15
16
17
18
19
11
1
2
4
5
6
7
8
9
12
3
10
20

10
1. POWERHEAD-IncludestheEngine,Clutch,FuelSystem,IgnitionSystemandRecoilStarter.
2. GRIP,RIGHTHANDREAR-Cushionedgripforrighthand.
3. THROTTLETRIGGERLOCKOUT-Thislevermustbeheldduringstarting.Operationofthethrottletriggeris
prevented unless throttle trigger lockout lever is engaged.
4. "STOP SWITCH" - mounted on top of the Throttle Trigger Housing. Move switch FORWARD to RUN, BACK to
STOP.
5. GRIP,LEFTHAND,FRONT-CushionedgripforLeftHand.
6. DRIVESHAFTASSEMBLY-ContainstheFlexibleDriveCable.
7. BLADES - Double reciprocating blades mounted to a blade support bar. Double sided blades, are capable of cutting
on either side of the blade.
8. GEARHOUSINGASSEMBLY-Gearhousingassemblyfixedstraightextension.
9. THROTTLETRIGGER-Springloadedtoreturntoidlewhenreleased.Duringacceleration,depressgraduallyfor
best operating technique.
10. BLADE COVER - Used to cover blade during transport and storage. Remove blade cover before using unit.
11. SPARKPLUG-Providessparktoignitefuelmixture.
12. TOPGUARD-Protectsarmfromthehotengine.
13. SPARKARRESTOR-CATALYTICMUFFLER/MUFFLER-Themufflerorcatalyticmufflercontrolsexhaustnoise
and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep
exhaustareaclearofflammabledebris.
14. FUELTANK-Containsfuelandfuelfilter.
15. RECOILSTARTERHANDLE-Pullhandleslowlyuntilstarterengages,thenquicklyandfirmly. Whenengine
starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.
16. FUELTANKCAP-Coversandsealsfueltankopening.
17. PRIMERBULB -Pumpingprimerbulbbeforestartingenginedrawsfreshfuelfromthefueltankprimingthecarbure-
tor for starting. Pump primer bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an
additional4 or5times.
18. AIRCLEANER-Containsreplaceablefilterelement.
19. CHOKECONTROL- Located on the top of the air cleaner housing. Move the lever to "COLD START" ( )to
close the choke for Cold Starting. Move lever to "RUN" ( ) position after engine fires.
20. SAFETYVIDEO-(Notincludedwithunit)P/N99922202800EnglishversionandP/N99922203513Spanishversion
areavailableata cost of$5.00fromECHO, INC. or anyauthorizedECHOdealer. The video overviewssafetyprecau-
tions and proper operating techniques and is supplemental to the Safety Manual. Read and understand the Safety
Manual for complete information on safe operation.

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 11
SPECIFICATIONS
MODEL -----------------------------------------------------SHC-260
Length------------------------------------------------------- 2230mm(87.8in.)
Width--------------------------------------------------------250mm(9.84in.)
Height -------------------------------------------------------250mm(9.84in.)
Weight (dry) ------------------------------------------------ 6.08kg(13.4lb.)
Engine Type ------------------------------------------------Air cooled, two-stroke, single cylinder gasoline engine
Bore----------------------------------------------------------34.0mm(1.34in.)
Stroke--------------------------------------------------------28.0mm(1.10in.)
Displacement -----------------------------------------------25.4cc(1.55cu.in.)
Exhaust ------------------------------------------------------Spark Arrestor Muffler w/catalyst
Carburetor --------------------------------------------------Walbrodiaphragmmodelw/primerpump
Ignition System -------------------------------------------- Flywheel magneto, capacitor discharge
SparkPlug --------------------------------------------------NGKBPM-8Y(Gap0.65mm(0.026in.)
Fuel ----------------------------------------------------------Mixed(GasolineandTwo-strokeOil)
Fuel/OilRatio -----------------------------------------------50:1two-strokeaircooledengineoil
Gasoline -----------------------------------------------------89 Octane unleaded. DO NOT use fuel containing methyl alcohol,
morethan 10%ethyl alcoholor 15%MTBE.
Oil ------------------------------------------------------------EchoPowerBlendTM PremiumUniversal2-StrokeOil
FuelTank Capacity ----------------------------------------0.58lit.(19.6USfl.oz.)
RecoilStarterSystem --------------------------------------AutomaticRecoilStarter
Clutch -------------------------------------------------------CentrifugalType
GearCaseRatio --------------------------------------------5.88:1
Cutter --------------------------------------------------------Double ReciprocatingBlade, DoubleEdge
Effective Length -----------------------------------------455mm(17.9in.)
Pitch ------------------------------------------------------35mm(1.4in.)
Idle Speed---------------------------------------------------2,400-3,200RPM
Wide Open Throttle Speed (W.O.T.) --------------------10,000-12,000RPM

12
ASSEMBLY
Tools Required: 4mmHexWrench,Screwdriver
Parts Required: Power Head/Drive Shaft Assembly and Gear Housing
Assembly.
GEAR HOUSING ASSEMBLY / DRIVE SHAFT
NOTE
Hedge Clipper Blades are very sharp. Wear gloves to protect
hands.
1. Fully loosen (do not remove) locating bolt (A) and align the
locating bolt (A) with the locating hole (B) in the Drive Shaft
Housing.
2. Slide the Gear Housing Assembly on the Drive Shaft. Be certain
theFlexDriveShaftengagesthehole in Driver Gear.
3. Tighten bolt (A) and clamping bolts (C).
DRIVE SHAFT ASSEMBLY /POWER HEAD
1. Loosen the bolt (A) at engine drive shaft clamp.
2. Carefully fit drive shaft assembly to engine making sure that
inner drive shaft engages into clutch mount.
NOTE
Lower gear housing cutter head assembly must be in line with the
engine.
3. Turn drive shaft housing so that center line of housing is midway
between the two arrows on shaft.
4. Tighten bolt (A).
A
A

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 13
THROTTLE LINKAGE AND IGNITION LEADS
1. Close choke and remove air filtercover.
2. Place inner cable in slot of carburetor swivel (A).
3. Loosen nut (B) and place threaded end of throttle linkage in bracket
slot. Finger tighten nut (B).
4. Check throttle for freedom of movement and that wide open throttle
/ low idle extremes are adjusted properly. If adjustment cannot be
achieved with adjusting nut (B), consult with your Echo Dealer for
correct adjustment procedure.
5. Tighten nut (B). Connect 2 ignition stop leads (C, D) from throttle
cable tubing to 2 ignition leads (C, D) on engine.
6. Bundle and secure ignition leads against engine housing with clip
(E).
7. Install airfilterand cover.
A
B
C
DE

14
PRE-OPERATION
FUEL
Fuel Requirements
Gasoline-Use 89Octane[R+M/2](mid gradeorhigher) gasoline known
to be good quality. Gasoline may contain up to 15% MTBE (methyl
tertiary-butylether).Gasoholcontainingmethyl(wood)alcoholisNOT
approved.
TwoStrokeOil-Atwo-strokeengineoilmeetingISO-L-EGD(ISO/CD
13738)andJ.A.S.O.FCStandards must be used.Echobrandpremium
Power Blend TM Universal 2-Stroke Oil meets these standards. Engine
problems due to inadequate lubrication caused by failure to use an ISO-
L-EGDandJ.A.S.O.FCcertifiedoil,suchasEchopremiumPowerBlend
TM, will void the two-stroke engine warranty. (Emission related parts
only are covered for two years, regardless of two-stroke oil used, per
the statement listed in the Emission Defect Warranty Explanation.)
IMPORTANT
EchopremiumPowerBlendTM Universal2-StrokeOilmaybemixed
at 50:1 ratio for application in all Echo engines sold in the past
regardless of ratio specified in those manuals.
Mixing Instructions
1. Fill an approved fuel container with half of the required amount of
gasoline.
2. Add the proper amount of 2-stroke oil to gasoline.
3. Close container and shake to mix oil with gasoline.
4. Addremaininggasolineandremix.
5. Install fuel container cap and wipe any spilled fuel from container
and surrounding area.
Handling Fuel
WARNING DANGER
FuelisVERYflammable.Useextremecarewhenmixing,storingor
handling or serious personal injury may result.
• Use an approved fuel container.
• DONOTsmokenearfuel.
• DONOTallow flamesorsparks nearfuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps
slowly allowing pressure to equalize.
• NEVERrefuelaunitwhentheengineis HOT!
• NEVERrefuela unitwiththe enginerunning.
• DONOTfillfueltanksindoors.ALWAYS fill fuel tanks outdoors
over bare ground.
• Securely tighten fuel cap after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or
operate unit until leakage is repaired.
IMPORTANT
Spilled fuel is a leading cause of
hydrocarbon emissions. Some states
may require the use of automatic fuel
shut-off containers to reduce fuel
spillage.ContactyourECHOdealerfor
orderinginformation.
After Refueling
• Wipe any spilled fuel from the unit.
• Moveatleast3m (10ft.)from refueling
location before starting the engine.
After use
• DO NOT store a unit with fuel in its tank.
Leaks can occur. Return unused fuel to an
approved fuel storage container.
Storage - Fuel storage laws vary by
locality. Contact your local government for
the laws affecting your area. As a precau-
tion, store fuel in an approved, air tight
container. Store in a well ventilated, unoccu-
pied building, away from sparks and flames.
Do not store fuel longer than 30 days.
IMPORTANT
Storedfuelages. Do notmixmorefuel
than you expect to use in thirty (30)
days, ninety (90) days when a fuel
stabilizerisadded.
IMPORTANT
Stored two-stroke fuel may separate.
ALWAYS shake fuel container thor-
oughly before each use.
oitaR1:05-xiMliOotleuF
.S.UCIRTEM
SAGLIOSAGLIO
snollaG.zo.lFretiL.cc
1
2
5
6.2 2.531 4
8
02
08 061 004

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 15
OPERATION
NOTE
The blade cover is used for transportation and storage. Remove
blade cover before using the unit.
STARTING COLD ENGINE
WARNING DANGER
The attachment will operate immediately when the engine starts
and could result in loss of control and possible serious injury.
Keep movable parts of the attachment off the ground and away
from objects that could become entangled or thrown.
1. Stop Switch
Move stop switch button (A) forward away from the STOP
position.
2. Close Choke
Move choke lever (B) to Cold Start ( ) Position.
3. Primer Bulb
Pumpprimerbulb(C) until fuel is visibleandflowsfreelyin the
clear fuel tank return line. Pump bulb an additional 4 or 5 times.
4. Recoil Starter
Lay the unit on a flat area and keep movable attachment parts clear
of all obstacles. Firmly grasp right hand grip and throttle trigger
lockout with left hand and fully depress throttle trigger to wide
open position. Rapidly pull recoil starter handle/rope (D) until
enginefires(ormaximumfive[5]pulls).
5. Choke
After engine fires (or five [5] pulls), move choke lever back to
“Run” ( ) position. Hold throttle trigger and throttle trigger
lockout fully depressed and pull recoil starter handle/rope until
engine starts and runs. Release throttle trigger and allow unit to
warm up at idle for several minutes.
NOTE
If engine does not start with choke in Run position after 5 pulls,
repeat instructions 2 - 5.
6. Throttle Trigger
After engine warm up, gradually depress throttle trigger to increase
engine RPM to operating speed.
B
D
A
C

16
D
A
A
C
STARTING WARM ENGINE
The starting procedure is the same as Cold Start except DO NOT close
the choke, and do not depress throttle trigger to wide open position.
WARNING DANGER
The attachment should not move at idle, otherwise serious
personal injury may result.
NOTE
If attachment moves, readjust carburetor according to “Carburetor
Adjustment” instructions in this manual or see your ECHO Dealer.
1. Stop Switch
Move stop switch button (A) away from the STOP position.
2. Primer
Pumpprimerbulb(C) until fuel is visibleandflowsfreelyin the
clear fuel tank return line. Pump bulb an additional 4 or 5 times.
3. Recoil Starter
Lay the unit on a flat area and keep movable attachment parts clear
of all obstacles. Rapidly pull recoil starter handle/rope (D) until
enginefires.
NOTE
If engine does not start after 5 pulls, use Cold Start Procedure.
STOPPING ENGINE
1. Throttle
Release throttle and allow engine to return to idle before shutting
off engine.
2. Stop Switch
Move stop switch button (A) backward to STOP position.
WARNING DANGER
If engine does not stop when stop switch is moved to STOP
position, close choke - COLD START position - to stall engine.
Have your ECHO dealer repair stop switch before using shaft
hedge clipper again.

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 17
MAINTENANCE
Your ECHO product is designed to provide many hours of trouble free service. Regular scheduled maintenance will help
achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an
ECHOServiceDealerformaintenance. Tohelpyoudecidewhether youwanttoDO-IT-YOURSELForhavetheECHO
Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO Dealer for repairs.
SKILL LEVELS
Level1= Easy to do. Most required tools come with unit.
Level2= Moderate difficulty. Some specialized tools may be required.
Level3= Experiencerequired.Specializedtoolsarerequired.ECHOrecommends
that the unit be returned to your ECHO dealer for service.
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier. Just below each task
heading are listed the various part numbers required for that task. See your ECHO dealer for these parts.
HEDGETRIMMING
NOTE
This unit is designed to cut shrubs and hedges with branches no
largerthan6mm(1/4in.)indiameter.
1. Holdtrimmerfirmlyandsqueezethrottletrigger toaccelerate
engine.
2. Tilt trimmer so cutting teeth are angled slightly toward the hedge or
shrub and proceed to cut.
WARNING DANGER
Never remove hands from unit when blades are moving.
WARNING DANGER
The engine continues running even when the blades have stopped
due to an obstruction. If this occurs, stop the engine, disconnect
ignition cable and remove the obstruction.

18
MAINTENANCEINTERVALS
/TNENOPMOC METSYS ECNANETNIAM ERUDECORP
D'QER LLIKS LEVEL ROYLIAD EROFEB ESU
YREVE LEUFER
3SHTNOM 09RO SRUOH 6SHTNOM 072RO SRUOH
YLRAEY 006 SRUOH
serudecorPecnanetniaMrelaeDohcEdednemmoceR
troPtsuahxErednilyCnobraceD/naelC/tcepsnI 3C/I
sedalBneprahSnaelC/tcepsnI 3)3(I
serudecorPecnanetniaMflesruoY-tI-oD
retliFriAecalpeR/naelC/tcepsnI 1C/I*R
ekohCnaelC/tcepsnI 2C/I
retliFleuFecalpeR/tcepsnI 1I*R
skael,metsySleuFecalpeR/tcepsnI 1*II
metsySgnilooCnaelC/tcepsnI 2C/I
rotserrAkrapSrelffuMecalpeR/tcepsnI 2*R/I
tfahSevirDesaerG 2)1(I
gnisuoHraeGesaerG 2)2(I
sedalBnaelC/tcepsnI 1)3(C/I
epoRretratSlioceRnaelC/tcepsnI 1*C/I
gulPkrapSnaelC/tcepsnI 2C/I*R
stloB/stuN/swercSecalpeR/nethgiT/tcepsnI 1*R/I
SEDOCRETTELERUDECORPECNANETNIAM NAELC=C,ECALPER=R,TCEPSNI=I:
-ETONTNATROPMI deriuqerfoycneuqerfehtenimretedlliwecneirepxeruoydnaesulautcA.mumixameranwohsslavretniemiT
.ecnanetniam :SETONERUDECORPECNANETNIAM)1( OHCEylppA
®
EBUL
MT
.sruoh52yreve
)2( OHCEylppA
®
EBUL
MT
sruoh52-51yreve
)3( .esugnirudyllacidoirepsedalbetacirbuL.dedeensaneprahsdnanaelcdnaedalbtcepsnI
*..noitcepsnignirudraewroegamadfognidnifehtnodesaberaecalperotsnoitadnemmocerllA

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 19
AIR FILTER
Level1
Tools required: 25or50mm(1or2in.)Cleaningbrush
Parts required: 90030REPOWERTM Air&FuelFilterKit
1. Close choke (Cold Start Position [ ]). This prevents dirt from
entering the carburetor throat when the air filter is removed.
Brushaccumulateddirtfromtheair cleaner area.
2. Remove the air cleaner cover. Clean and inspect the element for
damage. If element is fuel soaked and very dirty, replace.
3. If element can be cleaned and reused, be certain it:
• still fits the cavity in the air cleaner cover.
• is installed with the original side out.
NOTE
Carburetor adjustment may be needed after air filter cleaning or
replacement. See Carburetor Adjustment Section.
FUEL FILTER
Level1
Tools required: 200-250mm(8-10in.)lengthofwirewithoneendbent
into a hook, clean rag, funnel, and an approved fuel
container.
Parts required: 90030REPOWERTM Air&FuelFilterKit
WARNING DANGER
FuelisVERYflammable.Useextremecarewhenmixing,storingor
handling.
1. Use a clean rag to remove loose dirt from around fuel cap and
emptyfueltank.
2. Use the “fuel line hook” to pull the fuel line and filter from the
tank.
3. Remove thefilterfromthe line andinstallthenew filter.

20
SPARK PLUG
Level2
Tools Required: T-Wrench, feeler gauge, soft metal brush.
Parts Required: REPOWERTM Tune-UpKit P/N90075
1. Remove spark plug and check for fouling, worn and rounded
center electrode.
2. Clean the plug or replace with a new one. DO NOT sand blast to
clean.Remainingsandwilldamageengine.
3. Adjust spark plug gap by bending outer electrode.
4. Tightensparkplugto145-155kg/cm(125-135in.lb.).
COOLING SYSTEMS CLEANING
Level2
Tools required: Crossheadscrewdriver,4mmhexwrench,
cleaningbrush25or50mm(1or2 in.).
Parts Required: None.
IMPORTANT
To maintain proper engine operating temperatures, cooling air
must pass freely through the cylinder fin area. This flow of air
carries combustion heat away from the engine.
Overheating and engine seizure can occur when:
• Air intakes are blocked, preventing cooling air from reaching the
cylinder.
• Dust and grass build up on the outside of the cylinder. This build up
insulates the engine and prevents the heat from leaving.
Removal of cooling passage blockages or cleaning of cooling fins is
considered “Normal Maintenance.” Any failure attributed to lack of
maintenance is not warranted.
0.65 mm
(0.026 in.)