Eco-Smart G5 Series User manual

T8 LED Tube
G5 Series
G5 series T8 LED Tube is an economic solution for fluorescent replacement, which can directly drop
into existing T8, T10, T12 fixtures, without ballast or starter.
G5 Series adopts 5050 SMD LED diodes, and clear lens to maximize lumen output.
The lamp can produce equivalent illuminance as fluorescent tube while save more than 50% energy.
G5 Series comes with UL listed external power supply, input voltage 100-277VAC. With power supply
placed outside, G5 Series achieves good thermal property.
For heat management, the lamp uses patented and proven solution, which can dissipate heat from LED
chip to air quickly and efficiently. Without heat buildup, it makes reliable and optimizes performance and
life span of the lamp.
Distributed by: Eco-$mart, Inc. [phone] ph / [phone] fx / [email protected]

Features:
-Economic version, high cost-effective;
-Maximum lumen output with clear lens;
-Higher Brightness (Max. 1797(48”in) lm;)
-Stable performance with external power supply;
-50% Energy saving;
-Good light quality and good heat dissipation;
-Minimum maintenance costs;
-Green and eco-friendly lighting source without mercury.

Ordering Information
Part Number
Description
Unit
G5 EPS, Natural White, 40LEDs, 0.6m, Max. 36VDC, 120 degree, Clear Lens
pcs
G5 EPS, Natural White, 80LEDs, 1.2m, Max. 36VDC, 120 degree, Clear Lens
pcs
G5 EPS, Natural White, 100LEDs, 1.5m, Max. 36VDC, 120 degree, Clear Lens
pcs
Technical Specifications
Physical Specifications
Length
600 mm (1.96 ft)
1200 mm (3.93 ft)
1500 mm (4.92 ft)
Weight
220g
430g
520g
Housing
Aluminum
Cover
Clear PC
Tube Diameter
T8
Base Type
G13
Work Environment
Indoor use (applicable for dry environment)
Electrical Specifications
600 mm (1.96 ft)
1200 mm (3.93 ft)
1500 mm (4.92 ft)
LED Quantity
40LEDs
80LEDs
100LEDs
Power Consumption
9W ± 2W
18W ± 2W
21W ± 2W
Input Voltage
Max.36VDC
（Input Voltage of External Power Supply: 100~277VAC）
Power Factor
>0.96
Lighting Source
SMD LEDs
Operation Temperature
-20~40℃(-4~104℉)
Optical Specifications
600 mm (1.96 ft)
1200 mm (3.93 ft)
1500 mm (4.92 ft)
Lumens
890 ± 100 lm
1797 ± 100 lm
2100 ± 100 lm
Color Range
White
Color Temperature
42-4750K
CRI
>85
Beam Angle
120°
ECO-A-2G5
ECO-A-4G5
ECO-A-6G5
Distributed by: Eco-$mart, Inc. [phone] ph / [phone] fx / [email protected]

Page 1 of 4
Installation Guide LED T8 External Driver
NOTE:
Please read this entire manual to fully understand and safely use this product.
Specifications are subject to change without notice. Please visit www.atgelectronics.com for the most
recent user guide versions.
Included in this Box
ATG Electronics® iBright™ E58i T8 LED Tube (G5 EPS), 1 PCs
User Guide, 1 Set
Accessory Kit, 1 Set, including
-External Power Supply, 1 PCs
-Wire Nuts, 5 PCs
-Screws, 3 PCs
PLANNING THE INSTALLATION
iBright™ E58i can ONLY work with specific matching external power supply. Unmatched or other
specification power supplies will make iBright™ E58i burn out. Shown below in table 1 are matching
external power supplies compatible with iBright™ E58i.
Table 1: iBright™ E58i VS. Matching External Power Supply
.
Distributed by: Eco-$mart, Inc. [phone] ph / [phone] fx / [email protected]
External Power Supply

Page 2 of 4
Retrofit Luminaire with Electronic Ballast
Before
Figure 1
Installation Steps
Step 1: Turn off main power before installation
For safety, make sure main power source is switched off before attempting to install.
Step 2: Take existing fluorescent light out.
Existing fluorescent light is not needed. You might recycle it as appropriate.
Step 3: Open the ballast cover and disconnect all power wires from ballast and take the ballast out of the
fluorescent luminaire shown as Figure 2 below.
Keep one wire of each socket to connect with the external power supply. The other wire shall be cut off
immediately near the socket.
Figure 2
Step 4: Install the MATCHING external power supply shown as Figure 3 below.
The external power supply is sized to match the luminaire and to be installed near the middle of the
luminaire by 3M tape and screws provided.
Connect input wires of external power supply to main power outlet.
Connect output wires of external power supply to one of wires of T8 sockets at both sides with wire nuts.
Place the existing cover back to protect the external power supply.
Distributed by: Eco-$mart, Inc. [phone] ph / [phone] fx / [email protected]

Page 3 of 4
After
Figure 3
Step 5: Drop LED lamp into fluorescent luminaire. Switch main power on to light up LED lamp.
.
Retrofit Luminaire with Magnetic Ballast
Before Figure 4
Installation Steps
Step 1: Turn off main power before installation
For safety, make sure main power source is switched off before attempting to install.
Step 2: Take existing fluorescent light out.
Existing fluorescent light is not needed. You might recycle it as appropriate.
Step 3: Open the ballast cover and disconnect all wires from ballast and starter from T8 sockets shown
as Figure 5 below. Remove ballast from the fluorescent luminaire and recycle it as appropriate; keep
starter in position; keep one wire of each socket to connect with the external power supply. The other
wire shall be cut off immediately near the socket.
Figure 5
Distributed by: Eco-$mart, Inc. [phone] ph / [phone] fx / [email protected]

Page 4 of 4
Step 4: Install the MATCHING external power supply shown as Figure 6 below.
The external power supply is sized to match the luminaire and to be installed near the middle of the
luminaire by 3M tape and screws provided.
Connect input wires of external power supply to main power outlet.
Connect output wires of external power supply to one of wires of T8 sockets at both sides with wire nuts.
Place the existing cover back to protect the external power supply.
After
Figure 6
Step 5: Drop LED lamp into fluorescent Luminaire. Switch main power on to light up LED lamp.
T8 LED Tube Specifications
Input Voltage: Max.36VDC (Input Voltage of External Power Supply: 100-277VAC)
Color: White
LED Qty: 40LEDs, 80LEDs, 100LEDs
Power Consumption: 9W±2W, 17W±2W, 21W±2W
Beam Angle: 120 degree
Length: 600mm, 1200mm, 1500mm
Work Environment: Indoor use, dry environments
Ver7.3-111025
.
Distributed by: Eco-$mart, Inc. [phone] ph / [phone] fx / [email protected]