ecoey FJ183 User manual

PRODUCT SPECIFICATIONS
User Manual
Model: FJ183
Combo Smoke/CO Alarm
• Power Supply: 3V ( EVE CR17450 )
(non-replaceable, sealed-in battery)
• CO Alarm Sensitivity Setting:
Conforms to EN50291-1:2010+A1:2012
30PPM Without alarm before 120 minutes
50PPM Between 60 to 90 minutes
100PPM Between 10 to 40 minutes
300PPM Less than 3 minutes
• Sensor of Smoke: Photoelectric reflection
• Smoke Alarm Sensitivity: 0.09~0.15 dB/m
• Smoke Alarm Silence: About 10 minutes
• Sensor of CO: Electrochemical
• Product Life: 10 years after manufacture
• Alarm Sound:
≥85dB at 10ft @3.2±0.5KHz
I
l
N
a
S
u
T
A
na
LL
m
<
n
--
o
-
i
T
t
c
W
u
I
r
S
t
T
s
-
n
-
i
-
>
e
U
e
S
N
-
I
N
e
l
S
b
T
a
A
e
L
c
L
a
l
p
e
W
rt
A
o
R
n
N
y
I
r
N
e
G
t
-
t
B
a
TES T
SILENCE
W
O
=
L
F
L
A
E
U
Y
L
T
R
E
R
E
W
D
O
=
P
A
=
L
N
A
E
R
E
M
R
G
3
B
M
E
R
E
P
A
L
S
=
A
S
O
M
C
O
=
S
K
P
E
E
A
E
L
B
A
4
R
M
A
L
A
E
R
D
M
I
X
O
N
T
E
O
N
M
Y
E
N
A
O
R
B
S
R
S
A
E
C
R
V
&
I
E
C
K
E
O
T
I
M
M
S
E
A
D
-3
O
8
N
1
J
O
F
T
:
L
P
E
A
D
I
N
O
T
M

PRODUCT OVERVIEW GENERAL MAINTENANCE
• POWER indicator(green)
The green indicator is used to indicate power status of the
device. The green indicator will flash every 40 seconds.
• FAULT indicator(yellow)
The yellow indicator is used to indicate malfunctions or low
battery warning status of the device.
• ALARM indicator (red)
The red indicator is used to indicate alarm status of the
smoke alarm or CO alarm.
• TEST/SILENCE button
The TEST/SILENCE button is used to test the device and to
silence the unit during alarm. Press and hold to enable TEST
function, Or press to enable SILENCE function.
• Sounder
The sounder is used to send out smoke alarm, CO alarm
warning and abnormal warning information.
• Power on switch
The power on switch is used to power on the device .
The device MUST be installed on the matching bracket,
otherwise the device won't work.
• Deactivation switch
The deactivation switch is used to scrap the device.
To keep your Combo Smoke/CO alarm in good working order,
please follow these simple steps:
1. Verify the unit's alarm sound and indictors operation by enable
the TEST/SILENCE button once a week.
2. Remove the unit from the ceiling and clean the alarm cover and
vents with a soft brush attachment once a month to remove dust
and dirt.
3. Never use detergents or other solvents to clean the unit.
4. Avoid spraying air fresheners, hair spray, or other aerosols near
the device.
5. Do not paint the device. Paint will seal the vents and interfere
with the sensor's ability to detect CO. Never attempt to disassem
ble the unit or clean inside. This action will void your warranty.
6. As soon as possible, place the Combo Smoke/CO alarm back in
its proper location to assure continuous protection from fire and
carbon monoxide poisoning.
7. When household cleaning supplies or similar contaminants are
used, the area should be ventilated.
WARNING: The following substances can affect the sensor and may
cause false actions: methane, propane, isobutene, isopropanol,
ethylene, benzene, toluene, ethyl acetate, hydrogen sulfide, sulfur
dioxides, alcohol based products, paints, thinner, solvents,
adhesives, hair sprays, after shaves, perfumes and some cleaning
agents.
WARNING：Your Combo Smoke/CO alarm will not be operational
and will not monitor for smoke and CO levels without battery.
WARNING: This apparatus is designed to protect individuals from
the acute effects of carbon monoxide exposure. It will not fully
safeguard individuals with specific medical conditions. If in doubt
consult a medical practitioner.consult a medical practitioner.
MADE IN CHINA