Economic Holland Aerolet Safety guide

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
Toiletlift voor gehandicapten
Aerolet
Manual and Installation
®
Aerolet made by Economic Holland b.v.

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
2
Important information
Never change lift settings yourself, but leave this to
an authorized person.
Lift repairs may only be done when power is off !
Your Aerolet toilet lift is absolutely no toy !
Pay special attention to warning symbols used in
this manual.
!improper use may cause injury to the user !
!improper use may cause damage to the Aerolet !
Danger of hand-jam.
Measurements:
Width : 65 cm
Depth : 55 cm
Assembly bowl (ceramics) height: from 39 cm till max. 52 cm
Seat height position : min. 42,5 cm till max. 55,5 cm
Rise height Aerolet Basic : from 42,5 cm till max. 96 cm
Arm supports : withgoing (option)
Lower leg length : 36 - 53 cm
Net weight : 24 Kg (without arm supports)
Power : 100-230 V~50/60 Hz - 3,9A
Length power cable : 275 cm
Maximum load : 150 Kg

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
3
Table of contents
Important information...................................................................2
Base structure of the Aerolet .......................................................4
The Aerolet wire diagram.............................................................5
Operation instructions...............................................................6-7
Formation of the Aerolet ..........................................................8-9
Removal and installation of the covers..................................10-11
Prepair the Aerolet for a ´height´ toilet bowl (option)............12-13
Installing the Aerolet on a bowl (floor or wall hanging).........14-15
Installing the Aerolet in combination with Bidet-system.........16-17
Setting the rise of the Aerolet................................................18-19
Installing the arm supports (option) and the toilet seat..........20-21
Cleaning & maintenance............................................................22
Troubleshooting....................................................................23-24
Guarantee en repair...................................................................25
Notes....................................................................................26-27
Manufacturer and dealer............................................................28

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
4
Base structure of the Aerolet

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
5
The Aerolet wire diagram

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
6
Photo 1 Photo 2
Photo 3

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
7
Operation instructions
Danger of hand-jam.
When the lift is in motion your hand(s) must always be on the
arm supports or in your lap.
The Aerolet toilet lift operates by two easy press button on the
hand control (photo 3).
CThe [BUTTON LUP
(controls the upward movement of the lift)
CThe \BUTTON LDOWN
(controls the downward movement of the lift)
CThe Aerolet stops automatically at the level, which set from
the beginning.
CThe Aerolet stops with the release of either buttons.
CNo continued movement will occur once the lift reaches the
preset stopping point. The Aerolet toilet lifts’ drive system will
recalibrate itself each time when it reaches its lowest point.
!If both buttons are pressed at the same time, the lift will stop.
Please release both buttons for using the lift again.

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
8
Cistern bowl
Wall hanging
bowl

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
9
Formation of the Aerolet
CFor placing the lift at least 80 mm space is needed from the back
wall to the heart of the bowl holes at the height where the
fastening strip is fixed to the bowl. (see page 4 no. Î)
CThere must be sufficient space (minimum 50 mm) on each side of
the drive units to make cleaning possible. (see page 8)
CThe drawing below shows an example where the 100V-230V
socket (GFCI ground fault circuit interruptor) can be placed.
This is not necessary for 24V version (option).
Warning
During the lift rise the seat frame moves max. 60 mm backwards.
The free space between the seat frame and the wall is about 18 mm
at a seat height of 953 mm. (see Fig.1 - page 18)

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
10

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
11
Removal and installation of the covers
WARNING
•The user may NEVER remove or install the covers of the
lift.
• This should only be changed by a certified professional.
REMOVAL
• All covers are fastened to the frame with Velcro .
®
•For removal of the covers, the lift must be moved
upwards so that the hinge points D-D make a 30 degree
angle with the perpendicular sides of the lift.
•Remove the rivits Eout of the left and right cover A.
•Remove cover Afirst, then B and C.
INSTALLATION
•The lift must be placed in the same position as when the
covers were removed.
• Position the lift as described above for removal of the
covers.
• Install cover Cfirst, then Band A.
• The covers must overlap eachother.
! Please be sure that the covers are placed on the
outside of each other prior to operation of the lift.
Damage can occur to the covers if improper installed.

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
12

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
13
Prepair the Aerolet for a ‘height’ toilet bowl
(option)
!Before ordering and installing the Aerolet , the height of
®
the toilet bowl should be measured.
• Cut the 4 raisers at the right length (see diagram page 12).
CCarefully turn the lift backwards and ensure that the frame Ris
off the ground. Use a few wooden blocks to support.
CUnscrew the 4 existing feet J.
CRemove cover Cby seperating the Velcro connection.
CScrew the dimensioned raisers with the supplied bolts to the
frame and turn the feet into the raisers (see diagram page 12).
CSlide cover Cover frame R and fasten the Velcro.
CTurn the lift in upright position and install the lift to the toilet bowl.
Follow further the installation procedure in this manual.

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
14

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
15
Installing the Aerolet on a toilet bowl
(floor- or wall hanging toilet)
Warning
CSince the toilet lift is mounted on a toilet bowl, this toilet bowl
is part of the system. Make sure that the toilet bowl is firmly
anchored to the floor.
CRemove the existing seat from the toilet bowl.
CConnect the lift to 100-230 Volt and rise the seat frame by
approx. 15 cm so that fixation bow Ais visible.
!Press the fittings Ginto the mounting holes of the toilet
bowl. If neccessary, trim the fittings to fit the holes (see
detail page 14).
• Or use the fixation set with the expander B.
CAttach the fixation bow Ato the toilet bowl with the
mounting set. If necessary, turn adjusting feet S" so that
fixation bow Ais "flat" on the toilet bowl. Secure feet S".
CConnect the lift to 100-230 Volt and check the operation.
• If necessary, turn the adjustable feet S"and secure them.

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
16

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
17
Installing the Aerolet in combination with a
shower WC (Bidet-system)
CThe Aerolet lift in combination with a bidet system, is
possible in many cases.
CAn additional (extra) 100-230V socket and a water
connection must be made before placing this combination.
The drawing below shows an example. Read also the Bidet
installation manual.
CIt must be taken into account that this combination requires
more space from the toilet seat fixing points, at least 105 +
70 = 175 mm from the bowl seat holes to the cistern-pipe or
to the back wall if there is no pipe.
!This means that this combina-
tion cann´t be placed over a
closed couples or over a toilet
with a low-hanging cistern or a
wall-closet that is close to the
wall. Solution might be hanging
the cistern higher or replace
the bowl.
In that case there must be a
minimum space of 70 mm
between the bidet backside
and the cistern-pipe.
(See also pages 8-9)
Follow the installation instruc-
tions on page 14-16.

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
18
Fig.1

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
19
Setting the rise of the toilet lift
Warning
Never change the lift settings yourself, but have them done by
an authorized person.
! Height adjustments can ONLY take place when the adjust-
ment box for variable rise settings is present. This box (option)
can be ordered separately.
• Remove the hand control cable at
the rear of the lift.
• Plug the adjustment box cable in
• By pressing and holding the
toggle the switches the LED.
• Release the toggle when the
LED lights up at the correspon-
ding position: 1,2,3,4 or 5.
• Fig.1 - page 18 is an example of
the height adjustments
------ Adjustment box

Aerolet Manual + Installation - CO61 - version: 01 -EN - Jan. 2018
20
Photo 1 Photo 2