Ecox EIHPTC User manual

EIHPTC
EIHPTC
OWNER´S MANUAL
REMOTE CONTROL
CEILING FLOOR CONSOLE
Thank you for purchasing this ecox product.
Before using this machine, please read this manual and
retain it for future reference.

2
REMOTE CONTROL
CEILING FLOOR CONSOLE
EIHPTC
HANDLING THE REMOTE CONTROL
REMOTE CONTROL SPECIFICATIONS
FUNCTION BUTTONS
INDICATORS ON LCD
HOW TO USE THE BUTTONS
AUTO OPERATION
COOLING/HEATING/FAN OPERATION
DEHUMIDIFYING OPERATION
SWING OPERATION
TIMER OPERATION
ECO OPERATION
CONTENTS
4
3
5
8
7
9
8
9
14
8
10

3
REMOTE CONTROL
CEILING FLOOR CONSOLE EIHPTC
The air conditioner will not operate if curtains, doors or the materials block the signal
from the remote control to the indoor unit.
Prevent any liquid from failing into the remote control. Do not expose the remote control
to direct sunlight or heat.
If the infrared signal receiver on the indoor units is exposed to direct sunlight, the air
conditioner may not function properly. Use curtains to prevent the sunlight from failing
on the receiver.
If other electrical appliances react to the remote control, either move these appliances or
consult your local dealer.
Use the remote control within a distance of 8 meters / 26 feet from the appliance,
pointing it towards the receiver. Reception is conrmed by a beep.
LOCATION OF THE REMOTE CONTROL
CAUTIONS
1
2
3
The remote controller is powed by two
dry batteries (R03 / LR03/ AAA) X2 housed
in the rear part and protected by a cover.
Remove the cover by pressing and sliding o.
Remove the old batteries and insert the new
batteries, placing the(+) and (-) ends correctly.
Reattach the cover by sliding it back into
position.
REPLACING BATTERIES
HANDLING THE REMOTE CONTROL
8 mts.
26 ft.

4
REMOTE CONTROL
CEILING FLOOR CONSOLE
EIHPTC
REMOTE CONTROL SPECIFICATIONS
MODELO RG51Q/BG(C)E, RG51Q1/BG(C)E, RG51J(1)/(C)E,
RG51IJ(1)/BE(C)E
Rated Voltage 3.0V (Dry batteries LR03 X 2)
Lowest Voltage of CPU Emitting Signal 2.0V
Signal Receiving Range 8m (when using 3.0 voltage, it Gets 11m)
Environment -5º C ~ 60º C
1
2
3
4
Operating Mode: AUTO, COOL, DRY, HEAT (Cooling only model without) and FAN.
Timer Setting Function in 24 hours.
Indoor Setting Temperature Range 17º C ~ 30º C.
Full function of LCD (Liquid Crystal Display).
NOTE
NOTE
When the batteries are removed, the remote control erases all programming. After
inserting new batteries, the remote control must be reprogrammed.
Buttons design might be slightly dierent from the actual one you purchased depending
on individual models.
All the functions described are accomplished by the indoor unit. If the indoor unit has
no this feature, there is no corresponding operation happened when press the relative
button on the remote controller.
PERFORMANCE FEATURE
Do not mix old and new batteries or batteries of a dierent type. Do not leave the
batteries in the remote control if it is not going to be used for 2 or 3 months.
Dispose of the old batteries in the special containers.
CAUTIONS

5
REMOTE CONTROL
CEILING FLOOR CONSOLE EIHPTC
1
2
3
4
5
6
7
8
FUNCTION BUTTONS
TEMP UP Button
Push this button to increase the indoor temperature
setting in 1 ºC increments to 30 ºC.
TEMP DOWN Button
Push this button to decrease the indoor temperature
setting in 1ºC increments to 17 ºC.
MODE Button
Each time the button is pressed, the operation mode
is selected in the sequence of the following:
NOTE: Heat mode is for Cooling & Heating models only.
DIRECTION/SWING Button (For RG51Q models)
Used to stop or start horizontal louver movement or
set the desired up/down air ow direction. The louver
changes 6 degree in angle for each press. If keep
pushing more than 2 seconds, the louver will swing
up and down automatically.
SWING Button (For RG51Q1 models)
SWING Button (For RG51J models)
Used to stop or start horizontal louver movement .
SWING Button (For RG51Q(1) models)
Used to stop or start vertical louver move-ment .
AIR DIRECTION Button (For RG51Q1models)
Used to set the desired up/down air ow direction.
The louver changes 6 degree in angle for each press.
RESET Button
Once the recessed RESET button is pressed, all of the
current settings will be cancelled and the control will
return to the initial settings.
ON/OFF Button
Operation starts when this button is pressed and
stops when the button is pressed again.
FAN SPEED Button
Used to select the fan speed in four steps:
RG51Q/BG(C)
RG51Q1/BG(C)E
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
SWING
AIR
DIRECTION
FAN SPEED
SWING
TIMER ON
ECO
ON/OFF
TIMER OFF
RESET C/H
5
SET TEMPERATURE( C)
Auto Low Med High
AUTO COOL
DRY
HEAT FAN
NOTE: Med fan speed is not available for RG51J models .
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
SWING
FAN SPEED
TIMER ON
ECO
ON/OFF
TIMER OFF
RESET LOCK
21
4
5
6
3
7
8
10
11
SET TEMPERATURE( C)
12
SWING
13
9

6
REMOTE CONTROL
CEILING FLOOR CONSOLE
EIHPTC
9
10
11
12
13
TIMER ON Button
Press this button to activate the Auto-on time setting.
Each press will increase the time setting in 30 minutes
increments, up to 10 hours, then at 1 hour increments
up to 24 hours. To cancel the Auto-on time setting, just
press the button until the time setting is 0.0.
ECO Button
Select this function during the sleeping time. It can
maintain the most comfortable temperature and save
energy. This function is available on COOL, HEAT or
AUTO mode only .
NOTE: To cancel Energy-Saving mode, press MODE, FAN SPEED or ON/
OFF button.
TIMER OFF Button
Press this button to activate the Auto-o time setting.
Each press will increase the time setting in 30 minutes
increments, up to 10 hours, then at 1 hour increments
up to 24 hours. To cancel the Auto-o time setting, just
press the button until the time setting is 0.0.
LOCK Button
Press this recessed button to lock all current settings, and
the remote control will not accept any operation except
that of the LOCK. Use the LOCK mode when you want to
prevent settings from being changed accidentally. Press
the LOCK button again to cancel the LOCK function. A
lock symbol will appear on the remote control display
when the lock function is activated.
NOTE: For RG51Q1 models, press the TEMP UP( ) and
DOWN ( ) button simultaneously for 3 seconds to activate/cancel
the LOCK function.
C/H Button (For RG51Q1 models only)
Press this recessed button to shift the mode between
Cooling only and Cooling & Heating according to the
feature of the machine . The factory default setting
mode is Cooling & Heating. For example, the unit you
purchased is Cooling only models, please press this
recessed button with a needle of 1mm to shift the
operation mode.
RG51J(1)/(C)E
RG51Q1/BG(C)E
AIR
DIRECTION
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
SWING
FAN SPEED
TIMER ON
ECO
ON/OFF
TIMER OFF
RESET LOCK
10
11
SET TEMPERATURE( C)
12
SWING
13
9
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
SWING
FAN SPEED
TIMER ON
ECO
ON/OFF
TIMER OFF
RESET LOCK
SET TEMPERATURE( C)
SWING
AIR
DIRECTION
13

7
REMOTE CONTROL
CEILING FLOOR CONSOLE EIHPTC
INDICATORS ON LCD
MODE display
Displays the current selected mode. Including AUTO,
COOL, DRY, HEAT (cooling & heating models only) and
FAN.
Transmission Indicator
This transmission indicator will light when remote
control transmits signals to the indoor unit.
Temp./Timer display
The temperature setting (from 17ºC to 30ºC) or timer
setting (0~24h) will be displayed. If FAN mode is
selected, there will be no display.
ON/OFF display
This indicator will be displayed when the unit is
operating.
MODE display (FAN mode)
FAN SPEED display
Displays the selected fan speed: AUTO, HIGH, MED(if
applicable) and LOW. Nothing displays when the fan
speed is selected in AUTO speed. When AUTO or DRY
Mode is selected, there will be no signals displayed.
TIMER display
This display area shows the settings of the TIMER. That
is, if only the Auto-on time function is set, it will display
TIMER ON. If only the Auto-o time function is set, it will
displayTIMER OFF. If both functions are set, it will display
TIMER ON OFF which indicates you have chosen both
the Auto-on time and Auto-o time.
LOCK Indicator
LOCK display is displayed when pushing the LOCK
button. Push the LOCK button to clear display.
TIMER ON OFF
SET TEMPERATURE

8
REMOTE CONTROL
CEILING FLOOR CONSOLE
EIHPTC
HOW TO USE THE BUTTONS
AUTO OPERATION
COOLING /HEATING/FAN OPERATION
Ensure the unit is plugged in and power is available.
The OPERATION indicator on the display panel of the
indoor unit illuminates.
Press the MODE button to select Auto.
Press the TEMP button to set the desiredtemperature.
The temperature can be set within a range of 17 ºC~
30 ºC in 1ºC increments.
Press the ON/OFF button to start the air conditioner.
NOTE:
In the Auto mode, the air conditioner can logically choose the mode
of Cooling, Fan, Heating and Dehumidifying by sensing the dierence
between the actual ambient room temperature and the set temperature
on the remote controller.
In the Auto mode, you can not switch the fan speed. It will be
automatically controlled by the unit.
If the Auto mode is not comfortable for you , the desired mode can be
selected manually.
Ensure the unit is plugged in and power is available.
Press the MODE button to select COOL, HEAT,(cooling
& heating models only) or FAN mode.
Press the TEMP button to set the desiredtemperature.
The temperature can be set within a range of 17 ºC~
30 ºC in 1ºC increments.
Press the FAN SPEED button to select the fan speed
in four steps- Auto, Low, Med,or High.
Press the ON/OFF button to start the air conditioner.
NOTE
In the FAN mode, the setting temperature is not displayed in the remote
control and you are not able to control the room temperature either. In
this case, only step 1, 3 and 4 may be performed.
3
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
SWING
FAN SPEED
DIRECTION
/SWING
TIMER ON
ECO
ON/OFF
TIMER OFF
RESET LOCK
2
1
SET TEMPERATURE( C)
4
3
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
SWING
FAN SPEED
DIRECTION
/SWING
TIMER ON
ECO
ON/OFF
TIMER OFF
RESET LOCK
2
1
SET TEMPERATURE( C)
1
1
1
2
2
2
3
3
3

9
REMOTE CONTROL
CEILING FLOOR CONSOLE EIHPTC
DEHUMIDIFYING OPERATION
SWING OPERATION
Ensure the unit is plugged in and power is available.
The OPERATION indicator on the display panel of the
indoor unit illuminates.
Press the MODE button to select DRY mode.
Press the TEMP button to set the desiredtemperature.
The temperature can be set within a range of 17 ºC~
30 ºC in 1 ºC increments.
Press the ON/OFF button to start the air conditioner.
NOTE
In the Dehumidifying mode, you can not switch the fan speed. It will be
automatically controlled by the unit.
Use the DIRECTION/SWING button to adjust the
horizontal louver, use the SWING button to adjust the
vertical louver.
For RG51Q/BG(C)E models, when you press the
DIRECTION/SWING ( ) button, the louver changes 6
degrees in angle for each press. If keep pushing more
than 2 seconds, the louver will swing up and down
automatically. Press the SWING ( ) button, the
vertical louver will swing left and right automatically.
For RG51J/(C)E models, when the SWING button
is pressed, the louver will swing up and down
automatically.
For RG51Q1/BG(C)E models, press the SWING ( )
or ( ) button, the horizontal or vertical louver will
swing automatically. When the AIR DIRECTION button
is pressed, the louver changes 6 degrees in angle for
each press.
NOTE
When the louver swing or move to a position which would aect the
cooling and heating eect of the air conditioner, it will automatically
change the swing / moving direction.
1
1
2
2
3
3
3
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
SWING
FAN SPEED
DIRECTION
/SWING
TIMER ON
ECO
ON/OFF
TIMER OFF
RESET LOCK
2
1
SET TEMPERATURE( C)
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
SWING
FAN SPEED
DIRECTION
/SWING
TIMER ON
ECO
ON/OFF
TIMER OFF
RESET LOCK
1
SET TEMPERATURE( C)

10
REMOTE CONTROL
CEILING FLOOR CONSOLE
EIHPTC
TIMER OPERATION
Press the TIMER ON button to set the auto-on time of
the unit. And press the TIMER OFF button can set the
auto-o time of the unit.
To set the Auto-on time.
Press the TIMER ON button. The remote controller
shows TIMER ON, the last Auto-on setting time and
the signal "h" will be shown on the LCD display area.
Now it is ready to reset the Auto-on time to START the
operation.
Push the TIMER ON button again to set desired Auto-
on time. Each time you press the button, the time
increases in 30 minutes increments, up to 10 hours,
then at 1 hour increments up to 24 hours.
After setting the TIMER ON ,there will be a onehalf
second delay before the remote control transmits the
signal to the air conditioner. Then, after approximately
another 2 seconds, the signal "h" will disappear and
the set temperature will re-appear on the LCD display
window.
To set the Auto-o time.
Press the TIMER OFF button. The remote control
shows TIMER OFF, the last Auto-o setting time and
the signal "h" will be shown on the LCD display area.
Now it is ready to reset the Auto-o time to START the
operation.
Push the TIMER OFF button again to set desired Auto-
o time. Each time you press the button, the time
increases in 30 minutes increments, up to 10 hours,
then at 1 hour increments up to 24 hours.
After setting the TIMER OFF ,there will be a one and
a half second delay before the remote controller
transmits the signal to the air conditioner. Then, after
approximately another 2 seconds, the signal "h" will
disappear and the set temperature will reappear on
the LCD display window.
1
1
2
2
3
3
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
SWING
FAN SPEED
DIRECTION
/SWING
TIMER ON
ECO
ON/OFF
TIMER OFF
RESET LOCK
2
1
SET TEMPERATURE( C)

11
REMOTE CONTROL
CEILING FLOOR CONSOLE EIHPTC
The eective operation time set by the remote control for the timer function is limited to
the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0,
8.5, 9.0, 9.5, 10, 11, 12, 13, 14, 15,16,17, 18, 19, 20, 21, 22, 23 and 24.
1
2
3
IMPORTANT
o
Set
Start
6 hours later
6.0h
EXAMPLE OF TIMER SETTING
TIMER ON
(Auto-on Operation)
The TIMER ON feature is useful when you want the
unit to turn on automatically before you return home.
The air conditioner will automatically start operating
at the set time.
Example:
To start the air conditioner in 6 hours.
Press the TIMER ON button, the last setting of starting
operation time and the signal "h" will show on the
display area.
Press the TIMER ON button to display "6:0h" on the
TIMER ON display of the remote control.
Wait for about 3 seconds and the digital display area
will show the temperature again. Now this function
is activated.

12
REMOTE CONTROL
CEILING FLOOR CONSOLE
EIHPTC
10h TIMER ON OFF
on
Set
Start
Stop
2 hours later
after settings
10 hours later
after settings
on
Set
Stop
10 hours later
10h TIMER OFF
EXAMPLE OF TIMER SETTING
1
1
2
2
3
3
4
5
TIMER OFF
(Auto-o Operation)
The TIMER OFF feature is useful when you want the
unit to turn o automatically after you go to bed. The
air conditioner will stop automatically at the set time.
Example:
To stop the air conditioner in 10 hours.
Press the TIMER OFF button, the last setting of
stopping operation time and the signal "h" will show
on the display area.
Press the TIMER OFF button to display "10h" on the
TIMER OFF display of the remote control.
Wait for about 3 seconds and the digital display area
will show the temperature again. Now this function
is activated.
COMBINED TIMER
(Setting both ON and OFF timers simultaneously)
TIMER OFF TIMER ON
(On Stop Start operation)
This feature is useful when you want to stop the air
conditioner after you go to bed, and start it again in the
morning when you wake up or when you return home.
Example:
To stop the air conditioner 2 hours after setting and
start it again 10 hours after setting.
Press the TIMER OFF button.
Press the TIMER OFF button again to display 2.0h on
the TIMER OFF display.
Press the TIMER ON button.
Press the TIMER ON button again to display 10h on
the TIMER ON display .
Wait for the remote control to display the setting
temperature.

13
REMOTE CONTROL
CEILING FLOOR CONSOLE EIHPTC
5h TIMER ON OFF
on
Set
Start
Stop
2 hours later
after settings
5 hours later
after settings
1
2
3
4
5
TIMER ON TIMER OFF
(O Start Stop operation)
This feature is useful when you want to start the air
conditioner before you wake up and stop it after you
leave the house.
Example:
To start the air conditioner 2 hours after setting, and
stop it 5 hours after setting.
Press the TIMER ON button.
Press the TIMER ON button again to display 2.0h on the
TIMER ON display.
Press the TIMER OFF button.
Press the TIMER OFF button again to display 5.0h on the
TIMER OFF display .
Wait for the remote control to display the setting
temperature.

14
REMOTE CONTROL
CEILING FLOOR CONSOLE
EIHPTC
CAUTIONS
The timer setting(TIMER ON or TIMER OFF) that in sequence occurs directly after the set
time will be sactivated rst.
ECO OPERATION
The ECO function enables the unit to automatically
increase(cooling) or decrease (heating) 1ºC per hour
for the rst two hours, then hold steady for the next
5 hours, after that the unit will stop operation. It can
maintain the most comfortable temperature and save
energy.
NOTE: The ECO function is only available under Cooling,
Heating and AUTO operation.
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
SWING
FAN SPEED
DIRECTION
/SWING
TIMER ON
ECO
ON/OFF
TIMER OFF
RESET LOCK
1
SET TEMPERATURE( C)

15
REMOTE CONTROL
CEILING FLOOR CONSOLE EIHPTC