ECX BARRAGE User manual

Congratulations on your purchase of the ECX®Barrage®Gen2 4WD 1.55 Brushed
Scaler. This model introduces you to the sport of RC driving.
Herzlichen Glückwunsch zum kauf des ECX Barrage Gen2 4WD 1.55 Brushed
Scaler. Dieses Modell ist der gelungende Einstieg in die Welt des RC Cars Sports.
Nous vous félicitons pour l’achat de l’ECX Barrage Gen2 4WD 1,55 Brushed
Scaler. Ce modèle vous permettra de découvrir l’univers du RC.
Congratulazioni per l’acquisto dell’ECX Barrage Gen2 4WD 1.55 Brushed Scaler.
Questo modello dà accesso al mondo degli automodelli radiocomandati.
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’UTILISATION
MANUALE DI ISTRUZIONI
1:12 GEN2 4WD 1.55 BRUSHED SCALER RTR
ECX01013T1/T2 | ECX01013IT1/T2
®

2
EN
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS
Your new Horizon Hobby vehicle has been designed and built with a
combination of waterproof and water-resistant components to allow
you to operate the product in many “wet conditions,” including puddles,
creeks, wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not completely
waterproof and your vehicle should NOT be treated like a submarine.
The various electronic components used in the vehicle, such as the
Electronic Speed Control (ESC) and servo(s) are waterproof, however,
most of the mechanical components are water-resistant and should not
be submerged.
Metal parts, including the bearings, hinge pins, screws and nuts, as well
as the contacts in the electrical cables, will be susceptible to corrosion if
additional maintenance is not performed after running in wet conditions.
To maximize the long-term performance of your vehicle and to keep
the warranty intact, the procedures described in the “Wet Conditions
Maintenance” section below must be performed regularly if you choose
to run in wet conditions. If you are not willing to perform the additional
care and maintenance required, then you should not operate the vehicle
in those conditions.
CAUTION: Failure to exercise caution while using this product
and complying with the following precautions could result in
product malfunction and/or void the warranty.
General Precautions
• Read through the wet conditions maintenance procedures and make sure
that you have all the tools you will need to properly maintain your vehicle.
• Not all batteries can be used in wet conditions. Consult the battery
manufacturer before use. Do not use Li-Po batteries in wet conditions.
• The included transmitter is not waterproof or water-resistant. If using
a different transmitter than the one included, consult your transmitter's
manual or the manufacturer before operation.
• Never operate your transmitter or vehicle where lightning may be present.
• Do not operate your vehicle where it could come in contact with salt
water (ocean water or water on salt-covered roads), contaminated or
polluted water. Salt water is very conductive and highly corrosive, so use
caution.
• Even minimal water contact can reduce the life of your motor if it has not
been certified as water-resistant or waterproof. If the motor becomes
excessively wet, apply very light throttle until the water is mostly
removed from the motor. Running a wet motor at high speeds may rapidly
damage the motor.
• Driving in wet conditions can reduce the life of the motor. The additional
resistance of operating in water causes excess strain. Alter the gear
ratio by using a smaller pinion or larger spur gear. This will increase
torque (and motor life) when running in mud, deeper puddles, or any wet
conditions that will increase the load on the motor for an extended period
of time.
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product
literature, visit http://www.horizonhobby.com and click on the support tab for this product.
As the user of this product, you are solely responsible for operating in a
manner that does not endanger yourself and others or result in damage to the
product or property of others.
This model is controlled by a radio signal subject to interference from many
sources outside your control. This interference can cause momentary loss
of control, so it is advisable to always keep a safe distance in all directions
around your model as this margin will help avoid collisions or injury.
• Never operate your model with low transmitter batteries.
• Always operate your model in open spaces away from
full-size vehicles, traffic and people.
• Never operate the model in the street or in populated areas for any
reason.
• Carefully follow the directions and warnings for this and any optional
support equipment (chargers, rechargeable battery packs, etc.) you use.
• Keep all chemicals, small parts and anything electrical out of the reach
of children.
• Never lick or place any portion of the model in your mouth as it could
cause serious injury or even death.
• Exercise caution when using tools and sharp instruments.
• Take care during maintenance as some parts may have sharp edges.
• Immediately after using your model, do NOT touch equipment such as the
motor, electronic speed control and battery, because they generate high
temperatures. You may burn yourself seriously touching them.
• Do not put fingers or any objects inside rotating and moving parts, as this
may cause damage or serious injury.
• Always turn on your transmitter before you turn on the receiver in the car.
Always turn off the receiver before turning your transmitter off.
• Keep the wheels of the model off the ground when checking the
operation of the radio equipment.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the
product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic mechanical ability.
Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended
for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions
provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions
and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high
probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.
Age Recommendation: Not for children under 14 years.This is not a toy.
SAFETY PRECAUTIONS AND WARNINGS

3
EN
1:12 GEN2 4WD 1.55 BRUSHED SCALER RTR
Quick Start....................................................................................................3
Vehicle Preparations ....................................................................................4
Charging the Vehicle Battery ....................................................................4
Charging Warnings ...................................................................................4
Installing the Battery.................................................................................4
Transmitter Controls.....................................................................................5
Installing Transmitter Batteries ................................................................5
Binding ......................................................................................................6
Getting Started.............................................................................................6
Operation......................................................................................................7
When You Are Finished................................................................................7
Motor Care...................................................................................................7
Maintenance................................................................................................8
Setting the Gear Mesh..............................................................................8
Electronic Speed Control (ESC).................................................................8
Troubleshooting Guide .................................................................................9
Limited Warranty .......................................................................................10
Warranty and Service Contact Information...............................................11
FCC Information..........................................................................................11
IC Information.............................................................................................11
Replacement Parts.....................................................................................40
Optional Parts.............................................................................................41
Parts Diagram...................................................................................... 41–43
TABLE OF CONTENTS
COMPONENTS
Wet Conditions Maintenance
• Remove the battery pack(s) and dry the contacts. If you have an air
compressor or a can of compressed air, blow out any water that may be
inside the recessed connector housing.
• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt
off with a garden hose. Avoid rinsing the bearings and transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
• Use an air compressor or a can of compressed air to dry the vehicle and
help remove any water that may have gotten into small crevices or corners.
• Spray the bearings, drive train, fasteners and other metal parts with a
water-displacing light oil or lubricant. Do not spray the motor.
• Let the vehicle air dry before you store it. Water (and oil) may continue to
drip for a few hours.
• Increase the frequency of disassembly, inspection and lubrication of the
following:
• Front and rear axle hub assembly bearings.
• All transmission cases, gears and differentials.
• Motor—clean with an aerosol motor cleaner and re-oil the bushings
with lightweight motor oil.
• ECX®Barrage® Scaler
• ECX®2.4GHz 2-CH V4 Surface Transmitter (ECX13008)
• 100mAh 9V AC Charger with EC3™ Connector
• Dynamite®Speedpack®7.2V 900mAh NiMH battery
with EC3™ Connector (DYN1462)
• Dynamite® Tazer™ 390 Brushed Motor (DYNS1206)
• Dynamite®60A WP FWD/REV Brushed ESC (DYNS2210)
• ECX®2.4GHz 2-CH V4 Receiver (ECX13009)
• Spektrum™ Digital Servo (SPMS602)
• AA (4) Batteries
QUICK START
Please read the entire manual to gain a full understanding of the vehicle, fine-tuning the setup and performing maintenance.
1. Read the safety precautions found in this manual.
2. Charge a battery for the vehicle. Refer to the included
charging warnings and instructions for battery charging
information.
3. Install the AA batteries in the transmitter. Only use alkaline
or rechargeable batteries.
4. Install the fully charged battery in the vehicle.
5. Power ON the transmitter and then the vehicle. Wait 5 seconds for
the ESC to initialize. Always power the transmitter ON before the
vehicle and power it OFF after the vehicle has been powered OFF.
6. Check the steering and throttle control directions. Verify that the
servos are moving in the correct direction.
7. Drive your vehicle.
8. Perform any necessary maintenance.

4
EN
INSTALLINGTHE BATTERY
1. Remove the vehicle body.
2. Install a fully charged battery.
3. Secure the battery pack using the hook and loop straps.
4. Connect the battery pack to the ESC power connector.
CAUTION: Connecting the battery to the ESC with reversed
polarity will cause damage to the ESC, the battery or both.
Damage caused by incorrectly connecting the battery is not covered
under warranty.
VEHICLE PREPARATIONS
CHARGINGTHE VEHICLE BATTERY
NOTICE: Never charge a battery in the vehicle or damage may result.
1. Connect the NiMH battery to the battery charger.
2. Connect the charger to an AC power outlet.
3. Allow the NiMH battery to charge for 9 hours.
CHARGING WARNINGS
WARNING: Failure to exercise caution while using this product
and comply with the following warnings could result in product
malfunction, electrical issues, excessive heat, FIRE, and ultimately injury
and property damage.
• NEVER LEAVE CHARGING BATTERIES UNATTENDED.
• NEVER CHARGE BATTERIES OVERNIGHT.
• Read all safety precautions and literature prior to use of this product.
• Never leave the battery and charger unattended during use.
• Never allow children under 14 years of age to charge battery packs.
• Never attempt to charge dead or damaged batteries.
• Never charge a battery if the cable has been pinched or shorted.
• Never allow batteries or charger to come into contact with moisture
at any time.
• Never charge batteries in extremely hot or cold places (recommended
between 50–80°F [10–26°C]) or place in direct sunlight.
• Always use only Ni-MH rechargeable batteries. This charger cannot
charge batteries such as “heavy duty,” “alkaline,” “mercury” or
“lithium” battery.
• Always connect to the charger correctly.
• Always disconnect the battery and charger after charging and let
them cool between charges.
• Always inspect the battery before charging.
• Always terminate all processes and contact Horizon Hobby if the
product malfunctions.
• Always make sure you know the specifications of the battery to be
charged or discharged to ensure it meets the requirements of this
charger.
• Always constantly monitor the temperature of the battery pack while
charging.
• Always end the charging process if the charger or battery becomes
hot to the touch or starts to change form during the charge process.
• Always charge in a well ventilated area.

5
EN
1:12 GEN2 4WD 1.55 BRUSHED SCALER RTR
This transmitter requires 4 AA batteries.
1. Remove the battery cover from the transmitter.
2. Install the batteries as shown.
3. Install the battery cover.
CAUTION: If using rechargeable batteries, charge only
rechargeable batteries. Charging non-rechargeable batteries
may cause the batteries to burst, resulting in injury to persons
and/or damage to property.
CAUTION: Risk of explosion if battery is replaced with an
incorrect type. Dispose of used batteries according to national
regulations.
Power Switch
Power ON or OFF the transmitter
Reverse Switch
Allows you to change the direction of steering
(ST. REV) and throttle (TH. REV) controls (Ensure
proper function with a radio system test)
SteeringWheel
Controls RIGHT
and LEFT
steering
Solid Red: Battery voltage is
good (above 4V)
Flashing Red: Battery voltage
is critically low (below 4V).
Replace transmitter batteries
Battery Level Indicator
Steering Rate
Adjusts the amount the
front wheels move when the
steering wheel is turned left
or right
Throttle Dual Rate
Adjusts the maximum amount
of throttle the model can be
given
Adjusts the neutral point of
the electronic speed control
ThrottleTrim
Adjust to make the model
drive straight with no input
at the steering wheel
SteeringTrim
ThrottleTrigger
Controls power
to the motor for
forward or reverse
Stop ReverseForward
TRANSMITTER CONTROLS
INSTALLINGTRANSMITTER BATTERIES

6
EN
1. Power on the transmitter.
3. Perform a test of the transmitter’s control of the vehicle
with the vehicle’s wheels off the ground.
4. Start driving slowly, and, if the vehicle does not go straight,
adjust the steering trim dial on the transmitter.
IMPORTANT: Seat the motor brushes by driving smoothly on a flat
surface during use of the first battery charge. Properly seating the
motor brushes will increase the life and performance of the motor.
2. Connect the battery to the Electronic Speed Control
(ESC) / Receiver unit and
power on the vehicle .
BINDING
The included transmitter and receiver are bound at the factory. If you
need to rebind, follow the instructions below.
1. Power OFF the receiver and transmitter.
2. Connect a fully charged battery to the ESC.
3. Insert the bind plug into the receiver’s binding pins and
power ON the ESC. The receiver LED flashes.
4. Power ON the transmitter.
5. The receiver LED turns solid when binding in successful.
You must rebind when binding the receiver to a different transmitter.
NOTICE: Do not attempt to bind the transmitter and receiver if
there are other compatible transmitters in bind mode within 400
feet. Doing so may result in unexpected binding.
GETTING STARTED

7
EN
1:12 GEN2 4WD 1.55 BRUSHED SCALER RTR
• ALWAYS turn on your transmitter before you turn on the receiver
in the vehicle. Always power off the receiver before turning your
transmitter off.
• ALWAYS operate your vehicle in a wide open area. Operating the
vehicle in a small space or indoors can cause overheating at low
speeds. Operating at low speed increases heat in the electronic
speed control (ESC). Overheating can damage the vehicle and failure
may result.
OPERATION
WHENYOU ARE FINISHED
• Seat the motor brushes by driving smoothly on a flat surface during
use of the first battery charge. Failing to do so can greatly
reduce motor performance and functional life.
• Prolong motor life by preventing overheating conditions.
Undue motor wear results from frequent turns, stops and starts,
pushing objects, driving in deep water and tall grass, and driving
continuously up hill. Allow the motor to cool completely
before running the vehicle.
• Over-temperature protection is installed on the ESC to prevent
circuit damage, but cannot protect the motor from driving against
heavy resistance.
MOTOR CARE
1. Power off the ESC. 2. Disconnect the battery.
4. Remove the battery from the vehicle.
3. Power off the transmitter.
5. Recharge the battery.

8
EN
MAINTENANCE
SETTINGTHE GEAR MESH
The gear mesh has already been set at the factory. Setting the gear mesh
is only necessary when changing motors or gears.
You must remove the vehicle’s gear cover (A) to make this adjustment.
Proper gear mesh (how the gear teeth meet) is important to the
performance of the vehicle. When the gear mesh is too loose, the spur
gear could be damaged by the pinion gear of the motor. If the mesh is too
tight, speed could be limited and the motor and ESC will overheat.
Set the gear mesh by following these simple steps:
1. Loosen the 2 motor screws (B).
2. Put a small piece of paper (C) between the pinion and spur gears.
3. Push the gears together while tightening the motor screws.
4. Rotate the gears to remove the paper. The gearing should move a
small amount.
5. Reinstall the gear cover.
Connecting
1. Connect the RED (+) ESC wire to the RED (+) motor wire.
2. Connect the BLACK (–) ESC wire to the BLACK (–) motor wire.
NOTICE: Always disconnect the battery from the ESC when
you have finished operating your vehicle. The ESC’s switch only
controls power to the receiver and servos. The ESC will continue
to draw current when connected to the battery, resulting in
possible damage to the battery through over-discharge.
Calibrating
Ensure proper ESC function by calibrating the ESC to your transmitter
inputs.
1. Power OFF the ESC.
2. Ensure your transmitter is powered ON, the throttle is not reversed,
the throttle trim is neutral and the throttle travel range is at 100%.
3. Keep the throttle at neutral and power ON the ESC.
4. The ESC automatically calibrates the throttle range after 3 seconds.
5. One long beep will sound when the ESC is ready to run.
Programming
The ESC comes with two jumpers pre-installed in the MODE: Forward/
Brake/Reverse) and BATT: Ni-MH configurations.
To change the mode to F/B/R (forward/brake/reverse) or F/R (forward/
reverse) or change the battery type to Li-Po:
1. Power OFF the ESC.
2. Disconnect the jumper from the default port and connect it to the
desired port.
3. Power ON the ESC.
If the jumpers are lost or not installed, the ESC will default to MODE:
F/B/R and BATT: Li-Po.
WARNING: Do not connect bind plugs or receiver servo leads
into the ESC programming port. Doing so may damge the ESC
and/or components.
ELECTRONIC SPEED CONTROL (ESC)
Mode Forward/
Brake/
Reverse
(F/B/R)
Forward/
Brake
(F/B)
Forward/
Reverse
(F/R ((Crawler
Mode))
Battery
(BATT)
Li-Po Ni-MH
A
B
C

9
EN
1:12 GEN2 4WD 1.55 BRUSHED SCALER RTR
TROUBLESHOOTING GUIDE
Problem Possible Cause Solution
Short Run Time Battery damaged/not charged Check/change battery
Motor dirty Check/clean
Sluggish Action
Motor dirty Check/clean
Bind in drivetrain Clean/adjust
Vehicle battery is not charged Replace/recharge
Controls Reversed ST. REV or TH. REV Change switch position
Motor/ESC overheat Over-geared for the driving environment Install smaller pinion on the motor
Does Not Operate
Transmitter batteries low Replace/recharge
Transmitter powered off Power on
ESC powered off Power on
Vehicle battery is not charged Replace/recharge
Dual-rate (D/R) steering and/or throttle knobs on
transmitter are turned to zero Adjust dual-rate (D/R) steering and/or throttle knobs to 10
Poor Range Transmitter batteries low Replace/recharge
Receiver antenna damaged Check/repair/replace
The system will not connect
Transmitter and receiver too near each other Move transmitter 3.3–9.8ft (1–3m) from receiver
Transmitter and receiver too near large metal
objects (vehicles, etc.) Move away from large metal objects (vehicles, etc.)
Throttle trim out of center on transmitter Set throttle trim on transmitter to zero. Turn off and on
transmitter and vehicle
Receiver accidentally put in bind mode so receiver
is no longer bound Rebind transmitter and receiver
The receiver goes into failsafe
mode a short distance away from
the transmitter
Check the receiver antenna to be sure it is not cut
or damaged
Make sure the antenna is in the antenna tube
Contact Horizon Product Support
The receiver quits responding
during operation
Low battery voltage Completely recharge battery
Loose or damaged wires or connectors between
battery and receiver
Do a check of the wires and connection between battery
and receiver. Repair or replace wires and/or connectors
Receiver and transmitter are not
bound
Transmitter accidentally put in bind mode, ending
bind to receiver Bind transmitter to receiver
Vehicle moves forward or back-
ward without input from user Throttle trim on transmitter not centered Adjust throttle trim to set neutral point
Car does not drive straight Steering trim on transmitter not centered Adjust steering trim so vehicle drives straight
No steering or lack of steering Steering dual-rate (D/R) not adjusted correctly Adjusts steering dual-rate (D/R) knob on transmitter to
desired steering throw
Servo failed Contact Horizon Product Support
No throttle or lack of throttle
Throttle dual-rate (D/R) not adjusted correctly Adjust the throttle dual-rate (D/R) knob on transmitter to
desired steering throw
ESC failed Contact Horizon Product Support
Motor failed Contact Horizon Product Support
Clicking noise in transmission
area
Dirt or rocks in spur gear Remove gear cover and inspect. If necessary, replace gear
Motor moved away from spur gear Reset gear mesh

10
EN
LIMITED WARRANTY
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the
product purchased (the “Product”) will be free from defects in materials and
workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii)
damage due to acts of God, accident, misuse, abuse, negligence, commercial
use, or due to improper use, installation, operation or maintenance, (iii)
modification of or to any part of the Product, (iv) attempted service by
anyone other than a Horizon Hobby authorized service center, (v) Product not
purchased from an authorized Horizon dealer, or (vi) Product not compliant
with applicable technical regulations or (vii) use that violates any applicable
laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO
OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY
AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE
IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES
THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY
MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be
that Horizon will, at its option, either (i) service, or (ii) replace, any Product
determined by Horizon to be defective. Horizon reserves the right to inspect
any and all Product(s) involved in a warranty claim. Service or replacement
decisions are at the sole discretion of Horizon. Proof of purchase is required
for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR
COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM
IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY
OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall
the liability of Horizon exceed the individual price of the Product on which
liability is asserted. As Horizon has no control over use, setup, final assembly,
modification or misuse, no liability shall be assumed nor accepted for any
resulting damage or injury. By the act of use, setup or assembly, the user
accepts all resulting liability. If you as the purchaser or user are not prepared
to accept the liability associated with the use of the Product, purchaser is
advised to return the Product immediately in new and unused condition to the
place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law
principals). This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. Horizon reserves the right to
change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty
support or service. Once assembly, setup or use of the Product has been
started, you must contact your local distributor or Horizon directly. This will
enable Horizon to better answer your questions and service you in the event
that you may need any assistance. For questions or assistance, please visit
our website at www.horizonhobby.com, submit a Product Support Inquiry, or
call the toll free telephone number referenced in the Warranty and Service
Contact Information section to speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country
you live and use the Product in, please use the Horizon Online Service Request
submission process found on our website or call Horizon to obtain a Return
Merchandise Authorization (RMA) number. Pack the Product securely using a
shipping carton. Please note that original boxes may be included, but are not
designed to withstand the rigors of shipping without additional protection.
Ship via a carrier that provides tracking and insurance for lost or damaged
parcels, as Horizon is not responsible for merchandise until it arrives and is
accepted at our facility. An Online Service Request is available at http://www.
horizonhobby.com/content/service-center_render-service-center. If you do
not have internet access, please contact Horizon Product Support to obtain a
RMA number along with instructions for submitting your product for service.
When calling Horizon, you will be asked to provide your complete name, street
address, email address and phone number where you can be reached during
business hours. When sending product into Horizon, please include your RMA
number, a list of the included items, and a brief summary of the problem. A
copy of your original sales receipt must be included for warranty consideration.
Be sure your name, address, and RMA number are clearly written on the
outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any
issue with a Li-Po battery, please contact the appropriate Horizon
Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales
receipt verifying the proof-of-purchase date. Provided warranty
conditions have been met, your Product will be serviced or replaced free of
charge. Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be
completed and payment will be required without notification or
estimate of the expense unless the expense exceeds 50% of the
retail purchase cost. By submitting the item for service you are agreeing to
payment of the service without notification. Service estimates are available
upon request. You must include this request with your item submitted for
service. Non-warranty service estimates will be billed a minimum of ½ hour
of labor. In addition you will be billed for return freight. Horizon accepts money
orders and cashier’s checks, as well as Visa, MasterCard, American Express,
and Discover cards. By submitting any item to Horizon for service, you are
agreeing to Horizon’s Terms and Conditions found on our website http://www.
horizonhobby.com/content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in
the country of use and ownership. If received, a non-compliant
Product will not be serviced. Further, the sender will be
responsible for arranging return shipment of the un-serviced
Product, through a carrier of the sender’s choice and at the
sender’s expense. Horizon will hold non-compliant Product
for a period of 60 days from notification, after which it will be
discarded.
10/15

11
EN
1:12 GEN2 4WD 1.55 BRUSHED SCALER RTR
FCC ID: XNZECX13008 This equipment has been tested and found
to comply with the limits for Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTICE: Modifications to this product will void the user’s authority
to operate this equipment.
RF Radiation Exposure Statement
1. This Transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20 centimeters
between the radiator and your body.
FCC INFORMATION
IC INFORMATION
IC: 20264-ECX13008 This device complies with Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired
operation of the device.
Country of
Purchase Horizon Hobby Contact Information Address
United States of America
Horizon Service Center
(Repairs and Repair Requests)
servicecenter.horizonhobby.com/
RequestForm/
4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
Horizon Product Support
(Product Technical Assistance)
[e-mail]
877-504-0233
Sales [e-mail]
800-338-4639
European Union Horizon Technischer Service [e-mail] Hanskampring 9
D 22885 Barsbüttel, Germany
Sales: Horizon Hobby GmbH [phone]
EU Compliance Statement: Horizon Hobby, LLC hereby
declares that this product is in compliance with the essential
requirements and other relevant provisions of the RED, EMC, and LVD
Directives.
A copy of the EU Declaration of Conformity is available online at:
http://www.horizonhobby.com/content/support-render-compliance.
Instructions for disposal of WEEE by
users in the European Union
This product must not be disposed of with other waste. Instead,
it is the user’s responsibility to dispose of their waste equipment
by handing it over to a designated collections point for the recycling of waste
electrical and electronic equipment. The separate collection and recycling of
your waste equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects human
health and the environment. For more information about where you can drop
off your waste equipment for recycling, please contact your local city office,
your household waste disposal service or where you purchased the product.
WARRANTY AND SERVICE CONTACT INFORMATION

40
Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio
Part # Description Beschreibung Description Descrizione
DYN1462 7.2V 900mAh NiMH Battery
EC3
7.2V 1200mAh Ni-MH Akku, EC3 Batterie Ni-Mh 7.2V 1200mA,
prise EC3
Batteria 7.2V 1200mAh Ni-MH,
EC3
DYNS1206 390 Motor, 22T Pinion 390 Motor, 22T Ritzel Moteur 390, pignon 22T Motore 390, Pignone 22T
DYNS2210 WP 60A FWD/REV Brushed
ESC
WP 60A Bürstenregler Vorwärts/
rückwärts
WP 60A Contrôleur à balais avant/
arrière
WP 60A ESC con spazzole
avanti/indietro
ECX1048 Body Clips (8) Karosserieklammern Schwarz (8) Clips de carrosserie (8) Clip carrozzeria (8)
ECX1060 M4 Locknut, Flanged (4) M4-Kontermutter, mit Flansch (4) Contre-écrous M4, bridés (4) Controdadi M4, flangiato (4)
ECX41007 1.55 Wheel, Black (2) 1.55 radkranz schwarz (2) Jante 1,55 noire (2) Ruota (2) 1,55 nera
ECX41008 1.55 Falken Wildpeak MT
Tire (2)
Reifen 1,55 Falken Wildpeak
MT (2) Pneu 1,55 Falken Wildpeak MT (2) Pneumatico 1,55 Falken Widepeak MT (2)
ECX13008 2.4GHz Surface Transmitter,
2-CH, V4 2.4GHz 2 Kanal Sender V4 2.4GHz Emetteur 2 voies, V4 2-Ch trasmettitore, V4
ECX13009 2.4GHz Receiver Waterproof,
4-Channel V4
2.4GHz 4 Kanal Empfänger
wasserfesten V4
2.4GHz Récepteur étanche 4
voies V4
2.4GHz ricevitore impermeabile
4Ch, V4
ECX210010 Body Set, Clear Karosseriesatz, farblos Carrosserie, transparente Set carrozzeria, trasparente
ECX211014 Front/Rear Bumper Set Stoßfänger Vorne/Hinten Set de pare-choc Av/Arr Set paraurti ant/post
ECX211015 Bumper Mount Stoßfängerhalter Support de pare-choc Supporto paraurti
ECX211016 Chassis Set Chassis Châssis Set telaio
ECX211017 Skid Plate Unterfahrschutz Plaques de protection Piastra di protezione
ECX211018 Shock Tower Dämpferbrücke Support d’amortisseurs Torre ammortizz.
ECX211019 Body Post Karosseriehalter Supports de carrosserie Supporti carrozzeria
ECX211020 Chassis Brace (2) Chassishalter (2) Renforts de châssis (2) Rinforzo telaio (2)
ECX211021 ESC & Battery Tray Regler und akkuhalter Support de batterie et contrôleur Supporto batteria e ESC
ECX212009 Spool 38T Spool 38T Spool 38T Corona 38T
ECX212010 Axle Pinion Gear 14T Ritzel 14T 1/18 4WD Temper Pignone 14T
ECX212018 Spur Gear 48P 60T (1) Hauptzahnrad 48P 60T (1) Couronne 48P 60T (1) Corona 48P 60T (1)
ECX212020 Transmission Outdrive Anriebsklauen Noix de sortie de transmission Bicchierini transmissione
ECX212021 Driveshaft (2) Antriebswelle (2) Cardan (2) Albero trasmissione (2)
ECX212022 Rear Hub (2) Radträger Hinten (2) Fusée arrière (2) Mozzo posteriore (2)
ECX212027 Steering Spindle V2 Lenkspindel V2 Set de fusées V2 Fusello sterzo V2
ECX212028 Front/Rear Hub Set, V2 Träger Set Vorne/Hinten, V2 Set d’étriers Av/Arr, V2 Set hub ant/post, V2
ECX213002 F/R Shocks Assembled (2) Dämpfer montiert Vorne/Hinten
(2) Amortisseurs Av/Arr assemblés (2) Ammortizzatori montati ant/ post (2)
ECX216003 Complete Hardware Set Kompletter Hardwaresatz Matériel de fixation complet Set minuteria completo
ECX217001 Spindle/Hub Bearing Set ECX Spindelset/Lagerset Set de roulements de fusées Set supporto fusello/hub
ECX220009 LED Replacement LED-Austausch DEL de rechange LED sostitutivi
ECX220010 Body Set, Blue Karosseriesatz, blau Carrosserie, bleue Set carrozzeria, blu
ECX220011 Body Set, Yellow Karosseriesatz, gelb Carrosserie, jaune Set carrozzeria, giallo
ECX221000 Servo mount and plate,
wheel hex, & pin
Servohalterung und Platte,
Sechskantrad und Stift
Support de servo et plaque,
hexagone de roue et broche
Piastra e supporto
servocomando, ruota esagonale
e perno
ECX222000 FR/RR Axle Housing, 132mm FR/RR-Achsgehäuse, 132 mm
Carter d’essieu avant/arrière,
132mm Carcassa assale FR/RR, 132 mm
ECX222001 390 Motor Plate 390 Motorplatte Plaque moteur 390 Piastra motore 390
ECX222002 FR/RR Axles FR/RR-Achse Essieux avant/arrière Assali FR/RR
ECX222003 Complete Transmission Komplettes Getriebe Transmission complète Trasmissione completa
ECX224000 Link Set Verbindungssatz Jeu de liens Set leveraggi
SPMS602 S602 Digital Servo SCT2 Digital Servo Servo digital SCT2 SCT2 Digital Servo

41
1:12 GEN2 4WD 1.55 BRUSHED SCALER RTR
Optional Parts / OptionaleTeile / Liste des options / Elenco parti opzionali
Part # Description Beschreibung Description Descrizione
DYN1471 7.2V 1750mAh NiMH 6C Flat
Battery, EC3: Minis
Flache Akkus Ni-MH 7,2V
1750mA, EC3: Mini 1/18
Mini 1/18: Batterie plate Ni-MH
7,2V 1750mA, prise EC3
Batteria piatta 6C NiMH 1750
mAh 7,2 V, EC3: Minis
DYN1473 7.2V 1200mAh Ni-MH
Battery, Long, EC3: Minis
Lange Akkus Ni-MH 7,2V
1750mA, EC3: Mini 1/18
Mini 1/18: Batterie longue Ni-MH
7,2V 1200mA, prise EC3
Batteria lunga NiMH 1200 mAh
7,2 V c/EC3: Minis
DYN1476 7.4V 2000mAh2S 30C LiPo,
Long, EC3
7,4V 2000mAh 2S30C LiPo,
lang, EC3
Batterie LiPo 7,4V 2000mAh 2S
30C, longue, EC3
Batteria LiPo da 7,4 V 2000 mAh
2S 30C, lunga, EC3
DYNC2000CA Prophet Sport NiMH 35W
AC Charger
Prophet Sport NiMH 35W AC-
Ladegerät
Chargeur Prophet Sport AC Ni-MH
35W
Caricabatteria AC Prophet Sport
NiMH 35 W
ECX210011 Body Set, Painted Karosserie lackiert Carrosserie peinte Carrozzeria, verniciata
ECX312005 Rear Hub Carrier, Alum Rädträger hinten, Alum Set d’étriers arrière, aluminium Supporto hub posteriore, allum.
ECX314005 Steering Spindle, Alum Lenkspindel, Aluminium Arbre de direction, aluminium Colonna dello sterzo, alum
ECX41004 1.9 Wheel, Black (2) 1.9 radkranz schwarz (2) Jante 1,9 noire (2) Ruota (2) 1.9 nera
ECX41005 1.9 Wheel, White (2) 1.9 radkranz weiß (2) Jante 1,9 blanche (2) Ruota (2) 1.9 bianca
ECX41006 1.9 Falken Wildpeak AT3W
Tire (2)
Reifen 1.9 Falken Wildpeak
AT3 W (2)
Pneu 1.9 Falken Wildpeak AT3
W (2)
Pneumatico 1.9 Falken
Widepeak AT3 W (2)
ECX220010 - Blue / blau / bleu / blu
ECX220011 - Yellow / gelb / jaune / giallo
ECX211014
ECX41008
ECX1048
ECX1048
ECX1048
ECX1048
ECX1060
ECX213002

42
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES |
ESPLOSO DEL MODELLO CON REFERENZA PEZZI
ECX211014
ECX216003
ECX211015 ECX211016
ECX216003
ECX216003
ECX211014
ECX216003
ECX211017
ECX211016
ECX216003
ECX216003
ECX211020 ECX211015
ECX216003
ECX211018
ECX216003
ECX211018 ECX216003
ECX211018 ECX211018
ECX216003
ECX216003
ECX216003
ECX224000
ECX216003
ECX213002
ECX213002
ECX224000
ECX216003
ECX216003
ECX216003
ECX211020
ECX13009
ECX211021
ECX216003
DYNS2210
ECX211021
ECX221000
ECX216003
ECX221000
DYNS1462
SPMS602
ECX216003

43
1:12 GEN2 4WD 1.55 BRUSHED SCALER RTR
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES |
ESPLOSO DEL MODELLO CON REFERENZA PEZZI
ECX222003
ECX212021
ECX212021
DYNS1206
ECX212018
DYNS1206
ECX222001
REAR AXLE | ESSIEU AVANT | ESSIEU ARRIÈRE | ASSE POSTERIORE
ECX216003
ECX212021
ECX212020
ECX222000
ECX222000
ECX222002
ECX221000
ECX216003
ECX217001
ECX217001
ECX212022
ECX216003
ECX217001
ECX221000
ECX217001
ECX212010
ECX216003
ECX217001
ECX212009
FRONT AXLE | VORDERACHSE | HINTERACHSE | ASSE ANTERIORE
ECX212021
ECX212020
ECX217001
ECX222000
ECX216003
ECX224000
ECX216003
ECX224000
ECX222000 ECX222002
ECX221000
ECX212027
ECX217001
ECX221000
ECX216003
ECX212027
ECX212027
ECX216003
ECX212028
ECX216003
ECX212010
ECX217001
ECX216003
ECX212009
ECX217001
ECX216003

www.ecxrc.com
ECX01013T1/T2
®
© 2018 Horizon Hobby, LLC. ECX, the ECX logo, Barrage, Dynamite, Speedpack, Prophet, Tazer, EC3, and the Horizon Hobby logo
are trademarks or registered trademarks of Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Updated 01/2017 56926