Edesa MC-120 User manual

Versión 1.2
Installation,operation and maintenance
manual
Heated Units
MC-120, MC-180, MCP-120, MCP-180, SMC-12, SMC-16

Versión 1.2 2
Installation,operation and maintenance manual.
HEATED UNITS
MC-120, MC-180, MCP-120, MCP-180, SMC-12, SMC-16
WARRANTY
Edesa Hostelera S.A. assumes liability for manufacturing defects only. This warranty excludes,
therefore, any liability for the incorrect handling or operation of the equipment by the customer or
user. This warranty will remain in effect for a period of 1 year and will cover components with
manufacturing defects only. Labour and transport costs are the exclusive responsibility of the
customer in all cases. Edesa does not accept any responsibility for defects attributable to transport
unless claims are made within 24 hours of receipt of the goods.
SPECIFICATIONS
•Made of stainless steel 18/10.
•Reinforced and insulated worktop with rounded corners.
•Have a reinforced central shelf.
•Sturdy legs with height8-adjustable feet.
•Hot zone with 2 sliding doors, and 4 sliding doors in the pass-through hot plate.
•Ventilated hot storage by fan and heaters.
•The temperature is regulated and controlled using a thermostatic control.
•Equipped with an analogue thermometer.
•Unit “on” indicator pilot light.
•Double-wall doors with ecological polyurethane insulation with a density of 40 kg
•Temperature range between +30ºC and +90ºC.
MC-120, MCP-120, SMC-12, SMC-16
Heating elements: 1 de 2000W
Consumption: 7A
MC-180, MCP-180
Heating elements: 1 de 1400W
1 de 2000W
Consumption: 15,5A
INSTALLATION
Place the unit on a flat surface and make sure that it is correctly levelled.
Connect the unit to the mains power supply (230V). Connect the unit to the mains power supply.
(See Diagrams)
Operation
Turn on the unit at the general on/off switch.
Select the working temperature by turning the thermostat control to the desired setting.
The pilot light located next to the thermostat turns on when the heating elements are in operation.
For optimum operation it is recommended to turn on the unit and allow it to heat up to the required
temperature b<0}
efore introducing the product with the doors closed .
Never obstruct the hot air vents located inside the lower hot section opposite the fan.

Versión 1.2 3
SAFETY PRECAUTIONS
Warning: As this unit is used for heating, the well is a high-temperature zone. Avoid direct
contact and take all appropriate safety precautions.
While work is being done on the heating system, the unit must be disconnected from the mains
power supply.
Take precautions when removing food from inside the chamber, as the temperature inside the unit
may be very high.
INSTALLATION DIAGRAM
FOR CONNECTING TO MAINS
1- Remove the Phillips screws and extract the front with
the controls as indicated.
2-The inlet for connecting the mains cable is located at
the bottom.
ACCESS TO ELECTRICAL INSTALLATIONS
1- Disconnect the unit from the mains.
2- Loosen the Phillips screws and extract the front
with the controls as indicated.
3- In order to access the fan and the heating elements
terminals, remove the hexagonal M4 bolts with a
wrench and slide open the side panel.

Versión 1.2 4
ELECTRIC DIAGRAM
1-Switch
2-Thermostat
3-Fan
4-Heater
5-Terminal strip
6-Indicator light
7-Relay
MC-120, MCP-120, SMC-12, SMC-16
MC-180, MCP-180

Versión 1.2 5
DECLARACIÓN DE CONFORMIDAD CE
DECLARATION OF CONFORMITY CE
cumplen con la directiva del Consejo de Europa:
comply with the directive of the Council of Europe:
Edesa Hostelera S.A.
C/ Can Milans 13
Pol. Ind. Can Milans
08110 Montcada I Reixac
Barcelona
Spain
declara bajo su responsabilidad que las mesas calientes de su fabricación:
declares, as manufacturer, that the hot cupboards:
Modelos / Models
MC-120, MCP-120, MC-180, MCP-180, SMC-12, SMC-16
89/392/CEE Directiva Seguridad General Máquinas / General Safety of Machines Directive
Barcelona
Fecha / Date: 21/10/2011
Registro Mercantil de Barcelona, tomo 31997, folio 82, hoja B201303, inscripción 1, A28/10/99 NIF: A 62029798