EdgeStar DWP63BL User manual

V3.0 05262023
EDGESTAR.COM
Countertop Dishwasher
DWP63BL / DWP63WH / DWP63SV
Owner’s Manual

2 3
Important Safety Information
Read all instructions carefully prior to use. For your safety, the information in this manual should be followed. Improper
use and/or handling can cause serious damage to the appliance and/or to the user, including, but not limited to re,
explosion, and/or electric shock, resulting in personal injury, or death. This dishwasher is intended for domestic use only;
any other use may invalidate the warranty.
Use this appliance only for its intended purpose as described in this Owner′s Manual.
!
Electrical Safety
• Connect the dishwasher to a grounded, permanent electrical system.
• Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
• Check with a qualied electrician or service representative if you are in doubt whether the appliance is
properly grounded.
• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
• Do not modify the power cord’s length.
• If the power cord is damaged, it must be replaced by the manufacturer, a service agent, or a qualied technician.
• Use only the correct power supply with appropriate amperage. Do not exceed the suggested power ratings.
• To minimize the possibility of electric shock, disconnect this appliance from the power supply before attempting
any maintenance.
• Turning the dishwasher OFF does not disconnect the appliance from the power supply.
• If your dishwasher is connected to a wall switch, ensure the switch is ON prior to use.
• If you choose to turn the wall switch OFF between wash cycles on dishwashers with electronic controls,
allow 5 - 10 seconds after turning the switch ON before touching the START/RESET button. This allows the
control system to reboot.
• Do not start or stop the dishwasher by switching the circuit breaker’s power on and o󰀨.
• Never plug or unplug the dishwasher with wet hands.
CAUTION: Hydrogen gas is ammable. Under certain conditions, hydrogen gas may be
produced in a water heater that has not been used for more than two weeks. To prevent the
possibility of damage and/or injury, turn on all hot water faucets and allow them to run for
several minutes. Do this before using any electrical appliance connected to the hot water
system. This simple procedure will release any built-up hydrogen gas. Since hydrogen gas
is ammable, do not smoke, use an open ame, or use any appliance during this process.
!
General Safety
• This dishwasher should be properly installed and placed in a location in accordance with the Installation
Instructions prior to operation.
• Do not attempt to repair or replace any part of your dishwasher unless it is specically recommended in this
manual.
• All other service maintenance should be completed by a qualied technician.
• Use this appliance only for its intended purpose as described in this Owner’s Manual.
• This dishwasher must be installed indoors.
• This appliance is not intended for use by children.
• Do not allow children to play with, on, or inside this or any appliance.
• Close supervision is necessary if this appliance is used near children.
• Use caution when opening or closing the door to avoid injury.
• Use only powder, liquid detergents, or rinse agents recommended for use in a dishwasher, and keep them out of
the reach of children.
• Using a detergent that is not specically designed for dishwashers may have an undesired result such as
excessive suds.
• To avoid damage to the door seal, place sharp items strategically.
• Load sharp knives handle-side up to reduce the risk of injury.
• Do not wash plastic unless it is marked as dishwasher safe. For plastic items not marked as dishwasher safe,
refer to the manufacturer’s recommendations.
• Do not operate your dishwasher unless everything enclosed is securely in place.
• Do not tamper with controls.
• Do not sit or stand on the door or dish rack of the dishwasher.
• The door should remain closed. Left in the down position, the door presents a tripping hazard.
• Do not discard the dishwasher without removing the door.
• Do not store or use combustible materials such as gasoline or other ammable vapors and liquids in the vicinity of
this or any other appliance.
• Contents washed in anti-bacterial mode (if available) may be hot to the touch. Use care before handling.
• Do not wash non-dishware items such as furnace lters, paint brushes, etc. in your dishwasher. Discoloration,
staining, and/or other damage to dishwasher may result.
• Do not touch the heating element during or immediately after use.
!
Note: This owner’s manual is provided for reference use only. Specications may change
without prior notice. Refer to the product label on the back of your dishwasher for the latest
technical information.

4 5
Table of Contents
Important Safety Information ..................................................................................................................... 2
Electrical Safety .......................................................................................................................... 2
General Safety............................................................................................................................ 3
First Time Operating Instructions............................................................................................................... 5
Introduction ....................................................................................................................................... 5
Parts Identication .................................................................................................................................... 6
Front View......................................................................................................................................... 6
Accessories ...................................................................................................................................... 6
Back View ......................................................................................................................................... 6
Preparing the Dishwasher for Use............................................................................................................. 7
Unpacking the Dishwasher ............................................................................................................... 7
Installation Requirements ................................................................................................................. 7
Clearance Requirements .................................................................................................................. 7
Water Requirements ......................................................................................................................... 7
Water Pressure ................................................................................................................................. 7
Water Temperature ........................................................................................................................... 7
Electrical Requirements.................................................................................................................... 7
Connecting the Dishwasher....................................................................................................................... 8
Disconnecting your Dishwasher ................................................................................................................ 10
Operating Instructions ............................................................................................................................... 10
Control Panel Functions ............................................................................................................................ 11
Wash Cycles.............................................................................................................................................. 11
Loading the Dishwasher............................................................................................................................ 13
AHAM: Six (6) Place Settings ........................................................................................................... 14
DOE: Four (4) Place Settings ........................................................................................................... 16
Detergent and Rinse Aid Dispensers......................................................................................................... 17
Using the Proper Detergent .............................................................................................................. 17
Amount of Detergent to Use ............................................................................................................. 17
Detergent Dispenser......................................................................................................................... 18
Rinse Aid Dispenser ......................................................................................................................... 18
Starting a Wash Cycle ...................................................................................................................... 19
Changing a Wash Cycle ................................................................................................................... 20
Completing a Wash Cycle................................................................................................................. 21
General Maintenance ............................................................................................................................... 22
Cleaning the Filter System................................................................................................................ 22
Removing the Filter System.............................................................................................................. 23
Cleaning the Dishwasher.................................................................................................................. 24
Protecting the Dishwasher Against Freezing .................................................................................... 25
Other Maintenance Suggestions ...................................................................................................... 25
Error Codes ...................................................................................................................................... 26
Troubleshooting......................................................................................................................................... 27
Specications ............................................................................................................................................ 29
First Time Operating Instructions
Before use, make sure all packaging labels and materials are removed from the unit. Be sure to keep track of all included
parts and pieces before discarding the packaging materials. It is advised that you keep the original box and packaging
materials in case you ever need to move or ship the appliance in the future.
Introduction
Thank you for purchasing this EdgeStar dishwasher. We hope that this purchase will be the beginning of a lasting
and rewarding relationship between you and EdgeStar. We will provide the customer support and exemplary products
necessary to nurture that relationship.
This manual contains important information regarding the proper installation, use, and maintenance of your dishwasher.
Following this manual will ensure that your product will work at its peak performance and e󰀩ciency.
Please save the original product packaging in case you need to safely transport your dishwasher.
For Your Records:
Please write down the model number and serial number below for future reference. Both numbers are located on the
ratings label on the back of your unit and are needed to obtain warranty service. You may also want to staple your receipt
to this manual as it is the proof of your purchase, and is also needed for service under your warranty.
Model Number:_____________________________________________________________
Serial Number:_____________________________________________________________
Date of Purchase:___________________________________________________________
For a more e󰀩cient experience, please do the following before contacting customer service:
• If you received a damaged product, immediately contact the retailer or dealer that sold you the product.
• Read and follow this instruction manual carefully to help you install, use, and maintain your dishwasher.
• Read the troubleshooting section of this manual as it will help you diagnose and solve common issues.
• Visit us on the web at https:/www.edgestar.com to register your product, download product guides, and
access additional troubleshooting resources and up-to-date information. You can also nd an interactive
self-diagnostic tool at https://support.edgestar.com
• If you need warranty service, our friendly customer service representatives are available via email at:
[e-mail].

6 7
Parts Identication
Front View Back View
Cup Shelf
Detergent
Dispenser
Rinse Aid
Dispenser
Spray Arm
Cutlery
Basket
Filter
Assy
Basket
Accessories
Inlet Pipe
Connector
Drain Port
Inlet
Hose
Drain
Hose
Quick
Connect
Faucet
Adapter
Preparing the Dishwasher for Use
Unpacking the Dishwasher
Use at least two people to move and install the dishwasher to prevent back and other types of injuries. Carefully remove
the packaging materials. Remove any shipping tape and glue from your dishwasher before using. Do not use sharp
instruments, rubbing alcohol, ammable uids, or abrasive cleaners to remove tape or glue. These products can damage
the surface of your dishwasher. Check to make sure the parts necessary for installation are included. If any parts are
missing, please contact our customer service. Put the dishwasher on a level and at surface that is able to support the
entire weight of the dishwasher fully loaded.
Installation Requirements
The dishwasher has been designed for a countertop installation. Please follow the instructions for clearance, water, and
electrical requirements.
Clearance Requirements
The minimum height clearance required to install your dishwasher on a counter top surface with overhead cupboards is
17-¾” (45cm).
Water Requirements
Make sure the water supply/faucet connection is within reach of the inlet and drain hose assembly (i.e. 22-¾” / 58 cm). If
your sink has a spray wand, it is recommended that the hose be disconnected and the hole plugged.
Water Pressure
For best results, incoming water pressure should be between 15 and 20 pounds per square inch (psi).
Water Temperature
For best results, the water temperature must be at least 120ºF (49ºC). To prevent damage to the dishwasher, the
temperature of the incoming water supply should not exceed 140ºF (60ºC).
Electrical Requirements
Read all safety precautions listed at the beginning of this manual. It is recommended that you use receptacles that cannot
be turned o󰀨 by a switch or pull chain.
Make sure there is an electrical supply (outlet) within reach of the electrical power supply cord.
The dishwasher is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock
hazard, the cord must be plugged into a mating 3-pronged and grounding-type wall receptacle providing 110-120V, 60Hz,
grounded in accordance with the National Electrical Code and local codes and ordinances. If a mating wall receptacle
is not available, it is the personal responsibility of the customer to have a properly grounded, 3-prong wall receptacle
installed by a certied electrician. Use a circuit that is rated for at least 10 Amps.
CAUTION: A hose that attaches to a spray wand can burst if it is installed on the same
water line as the dishwasher.
!

8 9
Connecting the Dishwasher
Inlet
Hose
Drain
Hose
Quick
Connect
Faucet
Adapter
Your dishwasher comes equipped with a Faucet Adapter, Quick Connect, Drain Hose, and Inlet Hose. The Faucet
Adapter must be installed on the faucet before you can connect the dishwasher. This adapter comes packaged inside
your dishwasher.
The Faucet Adapter is compatible with faucets inclusive of either male (outside) or female (inside) threaded faucet
connections.
1. Screw the Faucet Adapter onto (or into) the faucet
tap. Check for leaks (use Teon or plumbers tape to
eliminate any leaks if necessary).
2. Connect the six-sided connection of the drain hose to
the drain port connection on the back of the dishwasher
cabinet. To avoid damage to threads, do not over-
tighten.
3. Connect the star-shaped connection of the inlet hose to
the inlet port on the back of the dishwasher cabinet. Do
not over-tighten.
4. Connect the circular connection of the drain hose
onto the longer (bottom) male connection on the
Quick Connect.
5. Connect the circular connection of the inlet hose onto
the shorter (top) male connection on the Quick Connect.
6. Attach the Quick Connect assembly onto the Faucet
Adapter, by pulling down the outer locking collar on
the Quick Connect, while pushing the quick connect
assembly upward onto the Faucet Adapter.
7. Release the locking collar when the quick-connect
assembly snaps onto the Faucet Adapter. Verify the
connection is secure.
8. Slowly open the hot water line and check for any sign
of water leaks at all connections. If leaks are located,
immediately close the water supply and repair the hose
connections.
If your existing Faucet Adapter is not compatible with the “quick connect” hose assembly supplied, then the following
procedures should be followed:
• Connect the Faucet Adapter (included with dishwasher) to your faucet.
• If your faucet is inclusive of a ‘female’ type (threaded) connection, both rubber washers must be installed inside the
faucet adapter.
• If your faucet is inclusive of a ‘male’ type (threaded) connection, use only the standard rubber washer (0.2”/5mm thick)
supplied within the adapter. Remove the second rubber washer.
For Best Results:
Your dishwasher cleans by spraying a mixture of clean hot water and detergent (under pressure) against the soiled
surfaces of dishes. The water is pumped through a rotating spray arm, drained through a lter (removing food and soiled
particles) and pumped back through the spray arm. Soiled water is pumped out and replaced with clean water at the end
of each cycle (the number of times this is repeated depends on the wash cycle chosen)
Notes:
• Hard water conditions will adversely a󰀨ect the washing performance of your dishwasher.
• Hard water conditions will also contribute to ‘lime’ (white lm substance) deposits and/or ‘scaling’ on the
stainless steel surface of the dishwasher tub and heater element, located in the sump underneath the
removable lter screen. To assist in minimizing these conditions, it is recommended to periodically operate/
rinse the inside of the dishwasher (empty) using one (1) cup of white vinegar at least once a week.

10 11
Disconnecting your Dishwasher
1. Close the hot water supply at the faucet.
2. Disconnect the power supply cord.
3. Remember to release the water pressure inside the inlet hose.
4. The inlet hose is pressured when the water supply line is opened, even if closed immediately.
5. To release pressure: press and hold the red pressure relief button on the quick connect
assembly until the ow of water stops.
6. Disconnect the quick-connect hose assembly by pulling down on the outer locking collar,
releasing it from the faucet adapter.
CAUTION:
• Failure to relieve water pressure before disconnecting the quick connect assembly
from the faucet adapter may result in back pressure overspray.
• The inlet water temperature can be EXTREMELY HOT.
• Backpressure overspray could cause SEVERE burns and or scalding.
• Do NOT let children disconnect the dishwasher. Close supervision of children is always
important around appliances.
!
Operating Instructions
To get the best performance from your dishwasher, read all operating instructions and follow the checklist below.
The following things should be checked before using the dishwasher.
• The dishwasher is level.
• The inlet valve is open.
• The hot water faucet is open.
• There are no leaks at the drain and inlet ports.
• The unit’s power plug is connected to a grounded outlet.
• The power is switched on.
• There are no kinks in the drain and inlet hoses.
• All packing and printed materials are removed from the dishwasher.
Control Panel Functions
1. Power Button: Press to turn the dishwasher ON/OFF.
2. Rinse Aid Warning Light: Indicates when the rinse aid dispenser needs to be relled.
3. Wash Cycle Complete Light: Indicates when the current wash cycle has ended.
4. Program Selector: Press to select your wash cycle. The wash cycles will display in sequence.
5. Delay Button Increase: Press to increase the time of the delay by one (1) hour increments up to 24 hours.
This establishes how much time will elapse before the selected wash cycle will begin.
6. Display Screen: Shows the current dishwasher status (running or on delay) as well as the remaining run or
delay time.
7. Delay Button Decrease: Press to decrease the time of the delay by one (1) hour increments down to 0.
8. Start/Pause Button: Press to start or pause the dishwasher wash cycle.
4 5 6 7 8
1 2 3
Delay
Delay
P4
P
P1 P2 P3 P4 P5 P6 P7
ECO 
Wash Cycles
P1. Heavy
P2. Normal
P3. Light-ECO
P4. Glass
P5. Baby Care and Bottles
P6. Speed
P7. Rinse
The sequential order of the wash cycles is as follows. Full wash cycle descriptions are provided on the next page.

12 13
PROGRAM CYCLE SELECTION
INFORMMATION
DESCRIPTION OF
CYCLE DETERGENT RUNNING TIME (MIN)
ENERGY
(KWH)
WATER
(gal)
RINSE
AID
Heavy
P1
For the heaviest soiled
loads, such as pots,
pans,casserole dishes,
and dishes that have been
sitting with dried food on
them for a while.
Pre-wash
Pre-wash
Wash (140°F)
Rinse
Rinse
Rinse (154°F)
Drying
15g/.50 oz 100 0.49 3.3
Normal
P2
For normally soiled
loads,such as pots,
plates,glasses, and lightly
soiled pans.
Standard daily cycle.
Pre-wash
Pre-wash
Wash (118-126°F)
Rinse
Rinse
Rinse
Rinse (149°F)
Drying
15g/.50 oz 127-155 0.38-0.42 1.7-3.8
Light-ECO
P3
For lightly soiled loads,
such as glasses, crystal,
and ne china.
Pre-Wash
Pre-Wash
Wash (122°F)
Rinse
Rinse (140°F)
Drying
15g/.50 oz 75 0.32 2.8
Glass
P4
For lightly soiled crockery
and glass.
Pre-Wash
Wash (122°F)
Rinse
Rinse (140°F)
Drying
15g/.50 oz 70 0.28 2.2
Baby Care
P5
For lightly soiled loads,
such as glasses, crystal,
and ne china. Also great
for baby bottles.
Pre-wash
Pre-wash (122°F)
Wash (131°F)
Rinse
Rinse
Rinse (158°F)
Drying
15g/.50 oz 90 0.51 3.4
SPEED
P6
A shorter wash for lightly
soiled loads that do not
need drying.
Pre-wash (113°F)
Pre-wash (122°F)
Wash (131°F)
Rinse (131°F)
Rinse (140°F)
15g/.50 oz 45 0.31 2.8
RINSE
P7
Use for rinsing dishes
glasses and silverware
that will not be washed
right away.
Pre-wash
Rinse 24 0.03 1.1
ECO

Notes:
• ( ) Requires Rinse-Aid
• Normal-This program is the test cycle. Set the rinse-aid dispenser to position three (3).
Loading the Dishwasher
A properly loaded dishwasher is key for optimal performance. Overlling the dishwasher can reduce the dishwasher’s
e󰀩ciency. Furthermore, improper placement of items can hinder the performance of the unit.
This unit is optimized for holding six (6) place settings including:
• Six (6) cups
• Three (3) glasses
• Six (6) bowls
• Six (6) large plates
• Six (6) small plates
• Six (6) saucers
• Two (2) serving dishes
• Six (6) sets of cutlery
For optimal performance:
• Load hollow items such as cups and glasses
with the opening facing downwards so that
water will not collect in the container.
• Be sure to secure dishes and utensils so
items cannot be moved by sprayed water.
Dishes and cutlery that shift in the wash
cycle may hinder the spray arms from proper
motion, resulting in poorly washed dishes.
• Silverware should be placed in the basket
with handles at the bottom, except for knives
and other sharp objects that should be
loaded with handles up.
• If the silverware basket has side
baskets, spoons should be loaded into
individual slots.
• Make sure similar pieces of silverware do
not nest together.
• Long utensils should be placed
horizontally in the basket or on the
cup shelf.
Cutlery
Basket
CAUTION: Do not let any item extend through the bottom of the silverware basket.
This may prevent the spray arm from spinning.
!

14 15
AHAM: Six (6) Place Settings
Basket Plate Rack
The basket is fitted with plate racks
which can be stowed horizontally if
required.
Cutlery Basket
Silverware should be placed in the basket with handles at the bottom, except for knives and other sharp objects that
should be loaded with handles up.
• If the silverware basket has side baskets, spoons should be loaded into individual slots.
• Make sure similar pieces of silverware do not nest together.
• Long utensils should be placed horizontally in the basket or on the cup shelf.
WARNING: Always load sharp utensils with the sharp point down.
!
CAUTION: Do not let any item extend through the bottom of the silverware basket.
This may prevent the spray arm from spinning.
!

16 17
Detergent and Rinse Aid Dispensers
Using the Proper Detergent
Only use detergent specically made for use in dishwashers. Do not use dish soap or detergent pods or tabs. If using
powder detergent, keep the detergent dry and do not put powder detergent into the dispenser until you are ready to
wash dishes.
Using a detergent that is not specically designed for dishwashers or using detergent pods and tabs will cause the
dishwasher to ll with suds. During operation, these suds will spill out of the dishwasher vents and may cause an E4
error code.
While there may be no lasting damage to the dishwasher by using dishwashing detergent that is not formulated to work
with dishwashers, your dishes may not get fully clean.
CAUTION: Do not use dish soap or detergent pods or tabs. This will cause the dishwasher
to overow.
!
Amount of Detergent to Use
The amount of detergent to use depends on whether your water is hard or soft. Generally, only one tablespoon (1/2
ounce) of detergent is needed for a normal wash load.
-With hard water, you may need extra detergent to remove deposits that are left by minerals.
-With soft water, less detergent is needed. Too much detergent with soft water can cause a permanent cloudiness
of glassware, called etching.
To identify whether your water is hard or soft, contact your water department. A water softener is recommended for water
that contains twelve or more grains. Without it, lime can build up in the water valve, which could stick while open and
cause ooding.
For heavily soiled loads, use the HEAVY (P1) wash cycle, ll one or both of the interior cups, depending on the hardness
of your water, and also ll the open cup on the dispenser lid.
Use the information in the table below as a guideline to determine the amount of automatic dishwasher detergent to place
in the dispenser:
Number of Grains Detergent Cup(s) to Fill
Less than 4 15 cup
4 to 8 25 cup
8 to 12 15 and 25 cups
Greater than 12 15, 25, and the open cup
Dish
DOE: Four (4) Place Settings

18 19
Detergent Dispenser
The dispenser must be relled before the start of each wash cycle. Your dishwasher uses less detergent and rinse aid than
a conventional dishwasher.
Always add powdered detergent just before starting the dishwasher, otherwise it could get damp and not dissolve properly
during the wash cycle.
To Open the Wash Cover:
• Press the button and the wash cover will ip back, revealing the detergent dispensing cups.
Open
cup 
1 oz
.5 oz
Button
Rinse Aid Dispenser
The rinse aid is released during the nal rinse to remove spots, prevent new lm build-up on dishes, glasses, atware,
cookware, and plastic, and improve drying time. Your dishwasher is designed to use liquid rinse aids. The rinse aid
dispenser is located inside the door next to the detergent dispenser.
Filling the Dispenser
The rinse agent dispenser holds 3.5 oz. of rinse agent. Under normal conditions, this will last approximately one month.
Try to keep it full, but do not overll.
1. Make sure the dishwasher door is fully open.
2. Turn the dispenser cap counterclockwise and lift it out.
3. Add rinse agent until the indicator window looks full.
4. Clean up any spilled rinse agent with a damp cloth.
5. Replace the dispenser cap and turn clockwise to lock into place.
Relling the Dispenser
If the rinse aid dispenser needs to be relled, the rinse aid warning light on the control panel (located on the front of your
dishwasher) will turn on. The dispenser should be relled before falling below 1/4 full, to ensure that rinse aid continues to
be e󰀨ective and to prevent streaking and spotting.
15
25 25g & 15g
Cups
Rinse Aid Setting
The amount of rinse agent released into the nal wash can be adjusted. The factory setting is at the midpoint. If there are
rings of calcium (hard water) on dishes, try a higher setting.
To Adjust the Setting
Remove the dispenser cap. Then, turn the adjuster counterclockwise to increase the amount of rinse agent.

Adjustable setting
Dispenser cap
M
A
X
NOTE:
• Only use branded rinse aid for the dishwasher.
• Never ll the rinse aid dispenser with any other substances, such as liquid detergent.
Starting a Wash Cycle
Once the dishwasher is fully loaded follow these procedures to start the wash cycle:
• Ensure that the unit is connected to the power supply.
• Ensure that the water supply is turned on to full pressure.
• Add detergent.
• Verify that enough rinse aid is in the dispenser, if desired.
• Close the door and press the ON/OFF button to power the dishwasher on.
• Press the program button to select the desired wash cycle:
Heavy Normal Light Glass Baby Care Speed Rinse
• Press the +/- buttons to adjust the delay setting if desired.
• Press the START/PAUSE button, the dishwasher begins to start. If a delay time
was selected, the dishwasher will start after the delay.

20 21
NOTE: When the Start/Pause button is pressed during a wash cycle, the cycle is suspended
and the display time will stop blinking. The program will remain paused until the Start/
Pause button is pressed again to continue the cycle.
Changing a Wash Cycle
You can modify the washing cycle, but only when the dishwasher has been running for a short time. Otherwise, detergent
may have been released, and the appliance may have already drained the water. If this is the case, the detergent
dispenser must be relled.
CAUTION:
• Opening the door during the wash cycle may result in injury from scalding hot water.
• Ensure that wash cycle has fully stopped before opening the door to rell the detergent
dispenser if necessary
!
Pressing the START/PAUSE button for three (3) seconds or more will put the machine in a stand-by
state. At this point the cycle setting can be changed.
NOTE: If the door is opened during the wash cycle, the machine will be paused. Once the
door is closed, you need to press the Start/Pause button to continue the cycle.
Forgot to Add a Dish?
A dish can be added any time before the detergent dispenser opens.
1. Press the START/PAUSE button.
2. Open the door slightly, to stop the washing.
3. You can open the door after the spray arms stop spinning.
4. Add remaining dishes.
5. Close the door.
6. Press the START/PAUSE button. The dishwasher will restart after 10 seconds.
Completing a Wash Cycle
When the selected wash cycle has nished, the buzzer of the dishwasher will sound for eight (8) seconds.
Turn o󰀨 the dishwasher using the ON/OFF button, shut o󰀨 the water supply,and open the door carefully.
Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they
are still hot.
Removing the Dishes
1. Switch o󰀨 the dishwasher by pressing the ON/OFF button.
2. Turn o󰀨 the water tap.
3. Open the door carefully. Leave the door ajar and wait a few minutes before removing the dishes. This will allow the
dishes to cool and assist in the drying process.
4. Unload the dishwasher. It is normal for the dishwasher to be wet inside.
CAUTION:
• Opening the door during the wash cycle may result in injury from scalding hot water.
• Ensure that the dishwasher and water tap are o󰀨 before opening the door to avoid
potential injury
!

22 23
General Maintenance
Cleaning the Filter System
The lter system consists of a coarse lter, a main (at) lter, and a micro (ne) lter.
1. Coarse lter:
Larger items, such as pieces of bone or glass that could block the drain are trapped in the coarse lter.
To remove the items caught by the lter, gently squeeze the tab on the top of this lter and lift out.
2. Fine lter:
This lter holds soil and food residue in the cylindrical base and prevents the soil from being
redeposited on the dishes during wash cycle.
3. Main lter:
Food and soil particles trapped by this lter are broken down by a special jet on the spray arm and
washed down the drain.
The lter assembly – composed of the three lters above - e󰀩ciently removes food particles from
the wash water, allowing it to be recycled during the cycle. For best performance and results, the
lter assembly must be cleaned regularly. For this reason, it is a good idea to remove the larger food
particles trapped in the lter after each wash cycle by rinsing the lter assembly under running water.
Use a soft cleaning brush to clean the coarse lter and the ne lter.
1
2
3
Removing the Filter System
In order to remove the lter system for cleaning please follow these steps:
1. Turn the entire lter system counterclockwise and then pull upward.
2. Lift the coarse and ne lters out from the main lter.
3. Gently squeeze the tab on the coarse lter to remove it from the ne lter.
Simply reverse this sequence to reinstall the lter system.
NOTE:
• Never run the dishwasher without the lter system in place.
• Improper replacement of the lter system or damaged lters may reduce the
performance level of the dishwasher and/or damage dishes and utensils.
• Clean the entire lter system at least once a week when in use.
• Inspect the lters after each wash and remove any food remnants and clean under
running water.

24 25
Cleaning the Dishwasher
The control panel can be cleaned by using a lightly dampened cloth. Dry thoroughly with a soft towel.
Never use sharp objects, scouring pads, or harsh cleaners on any part of the dishwasher.
Cleaning the Door
To clean the edge around the door, you should use only a soft warm damp cloth. To prevent
water into the door lock or electrical components, do not use a liquid spray or cleaner of any
kind.
NOTE: Abrasive agents or some paper towels may scratch or leave spots on the stainless
steel interior surface.
Cleaning the Spray Arms
The spray arms can be removed for periodic cleaning of the nozzles to prevent possible clogging. Wash the spray arms
under running water and carefully reinstall them making sure that the movement is in no way impeded.
To remove, grasp the middle of the spray arm and pull it upwards. Reinstall the spray arm after cleaning and check that
the arms turn freely.
Protecting the Dishwasher Against Freezing
If there is a possibility the dishwasher could freeze due to a cold working environment, take the following steps after each
washing cycle:
1. Turn o󰀨 the dishwasher.
2. Turn o󰀨 the water supply and disconnect the water inlet hose from the back of the unit.
3. Drain the water from the inlet hose and inlet port. (Use a pan to catch the water.)
4. Reconnect the water inlet hose to the inlet port.
5. Remove the lter system and use a sponge to absorb the water that is in the lter (sump) area.
Other Maintenance Suggestions
In order to keep your dishwasher in good working order the following suggestions should be followed:
After Every Wash
Turn o󰀨 the water supply to the appliance and leave the door slightly open so that moisture and odors are not
trapped inside.
When Cleaning
Never use abrasive solvents when cleaning. Only use a dampened soft cloth with warm water. To remove spots or stains
from the interior surface you may use a cloth dampened with water and a little white vinegar.
Cleaning the Door Seals
Food that remains trapped in the seals may cause odors to form. Periodic cleaning with a damp sponge will prevent this
from occurring.
Clean the Filters Regularly
Cleaning the lters regularly will prevent clogs and odors from occurring.
Preparation for Storage
When preparing to put the dishwasher into storage, it is recommended that you run a wash cycle with the dishwasher
empty. Disconnect the unit from power. Remove any water remaining in the sump area with a terry cloth or absorbent
sponge. Turn o󰀨 the water supply and leave the door of the appliance slightly open. This will help the door seals to last
longer and prevent odors from forming inside the dishwasher.
If the Dishwasher Must be Moved
If the dishwasher must be moved, try to keep it in the upright position. Do not transport the unit on its side or upside down.

26 27
Items Not Suitable for Dishwasher Use:
• Cutlery with wooden, horn, china, or mother of pearl handles
• Plastic items that are not heat resistant
• Older cutlery with glued parts that are not heat resistant
• Bonded cutlery items or dishes
• Pewter or copper items
• Crystal glass
• Steel items subject to rusting
• Wooden platters
• Items made from synthetic bers
• Silver and aluminum parts have a tendency to discolor during washing
• Glazed patterns may fade if machine washed
• Some types of glasses can become dull after a large number of washes
Error Codes
Error Code Meaning Possible Causes
E1 Long water inlet time
The faucet may not be opened or the water
pressure may be too low. The water inlet
may also be kinked.
E3 Not reaching required
temperature Possible heating element malfunction.
E4 Overow
Dishwasher may be leaking or overowing
because the wrong type of detergent or
detergent pods are being used.
Ed Circuit board error There may be a break in the dishwasher’s
wiring / circuit.
Troubleshooting
Follow the troubleshooting guide below to resolve common issues:
PROBLEM POSSIBLE CAUSES SOLUTION
Dishwasher
does not
start
Fuse is blown or circuit breaker is
tripped
Replace fuse or reset circuit breaker. Remove
any other appliances sharing the same circuit
with the dishwasher.
Power Supply is not turned on
Ensure the dishwasher is turned on and the door
is closed securely.
Make sure the power cord is properly plugged
into the wall socket.
Dishwasher door is not properly closed Close dishwasher, ensuring that the door
latches.
Water not
pumped from
dishwater
Kink in drain hose Check drain hose.
Filter clogged Check coarse lter.
Kitchen sink clogged Ensure kitchen sink is draining well. If sink is not
draining, refer to a plumber.
Suds in tub Improper detergent
Use only the specied detergent. If improper
detergent was used, open the dishwasher
allowing suds to evaporate. Add one (1) gallon
of cold water to the tub. Close and latch the
door. Start the “RINSE” wash cycle to drain the
water. Repeat if necessary.
Spilled rinse aid Always clean up rinse aid spills immediately.
Stained tub
interior
Detergent used
contained colorant Do not use detergents with colorants.
White lm on
dishwasher
interior surface
Hard water minerals
While wearing rubber gloves, use a damp
sponge to clean the interior with dishwasher
detergent.
Never use any other cleaner to clean
dishwasher.
Rust stains
appear on
cutlery
Items are not noncorrosive Do not place non-dishwasher safe items in
dishwasher.
Knocking noise
inside of
dishwasher
The spray arm is knocking against an
item in the dish rack
Pause the wash cycle and rearrange the items
which are obstructing the movement of the spray
arm.
Rattling noise
inside of
dishwasher
Item is not securely placed in dish rack Pause the wash cycle and secure the items in
the dish rack.
Knocking noise
in water
pipes
Pipe cross-section may have problems Contact a plumber. This is not related to the
dishwasher.

28 29
PROBLEM POSSIBLE CAUSES SOLUTION
Black or gray
marks
on dishes
Utensils may have
rubbed against dishes
Use a mild abrasive cleaner to
eliminate marks. Load carefully.
Detergent left in
dispenser cup Dishes are blocking detergent cups Re-load dishwasher according to instructions in this manual.
Dishes are not
cleaned
Dishes were not loaded properly See notes on loading the dishwasher.
The wash cycle was not powerful
enough Select a more intensive wash cycle.
Not enough detergent was dispensed Use more or change brand of detergent.
Items are blocking the path of the
spray arms
Rearrange the items so the spray arms can fully
rotate.
The lter combination in the base
of the dishwasher is not clean or is
installed incorrectly
Clean and install the lter combination correctly.
Cloudiness on
glassware
Combination of too much detergent
with soft water
Use less detergent and/or select the shortest
wash cycle to clean glassware.
The lter may be dusty or blocked Clean the lter and replace it if needed.
The dishes are
not dry
Improper loading Re-load dishwasher according to instructions.
Not enough rinse aid Rell and/or increase the amount of rinse aid.
Dishes are removed too soon Do not remove dishes from dishwasher
immediately.
Wrong cycle selected Short cycles have lower cleaning performance.
Choose a more intensive cycle.
Cutlery has a lowquality coating Dishwasher is not suitable for low quality
coating.
Dishwasher Type Portable / Countertop
Model DWP63BL / DWP63WH / DWP63SV
Color Black / White / Silver
Number of Place Settings 6
Maximum Diameter of place Settings 10.5"
Wash Cycles 7
Accessories
Quick Connect Adapter
Faucet Adapter
Drain Hose
Water Inlet Hose
Operating Temperature (Normal
Wash) 125°F
Max Water Temperature (Rinse Cycle) 158°F
Water consumption (Normal Wash) 2.85 gallons
Spray Arms Plastic
Drain Pump Yes Yes
Drain Pump Maximum Vertical Lift 39”
Interior Stainless Steel (430 SS)
Voltage / Frequency 120V AC / 60Hz
Current 5.7A
Delay Start 1-24 Hour
Unit Dimensions (H x W x D) 17-5/16” x 21-5/8” x 19-5/8”
Net Weight 44.1 lbs.
Noise Level 52 dB
Specications

30 31
EdgeStar Limited Warranty
One (1) Year Parts & Ninety (90) Days Labor
This product is warranted by EdgeStar to be free from defective workmanship and materials, subject to any conditions set forth as follows:
WHAT IS COVERED:
LABOR: For a period of NINETY (90) DAYS from the date of original purchase, labor will be performed free of charge at an authorized
EdgeStar repair facility. At its option, EdgeStar will repair the product with new or remanufactured parts, or exchange the defective product
with a new, refurbished, or remanufactured product. If a product is replaced, it will carry the remaining warranty of the original product.
After the ninety (90) day period, EdgeStar will no longer be responsible for labor charges incurred. All defective products and parts
covered by this warranty will be repaired or replaced on a mail-in basis to an EdgeStar authorized repair facility.
PARTS: For a period of ONE (1) YEAR from the date of original purchase, EdgeStar will supply new, rebuilt, or refurbished parts free of
charge. EdgeStar may request a defective part be returned in exchange for the replacement part. All replacement parts or products will
be new, remanufactured, or refurbished. All products and parts replaced by EdgeStar under warranty service become the property of
EdgeStar.
This warranty applies to the original purchaser only, and only covers defects in workmanship experienced during operation of the product
under normal service, maintenance, and usage conditions. This warranty applies to the purchase and use of this product in residential
settings within the contiguous United States of America.
WHAT IS NOT COVERED:
The following limitations apply to the coverage of this warranty. This warranty does not cover:
–Labor charges for installation, setup or training to use the product.
–Shipping damage, and any damage caused by improper packaging for shipment to an authorized service center, and any damaged
caused by improper voltage or any other misuse, including abnormal service, handling, or usage.
–Cosmetic damage such as scratches and dents.
– Normal wear and tear on parts or replacement of parts designed to be replaced, e.g. lters, cartridges, batteries.
–Service trips to deliver, pick-up, or repair, install the product, or to instruct in proper usage of the product.
– Damages or operating problems resulting from misuse, abuse, operation outside environmental specications, uses contrary to
instructions provided in the owner’s manual, accidents, acts of God, vermin, re, ood, improper installation, unauthorized service,
maintenance negligence, unauthorized installation or modication, or rental or commercial use.
–Labor, service transportation, and shipping charges incurred 91 days or more after the date of original purchase.
–The use of EdgeStar products in commercial or rental settings.
–Optional accessories, attachments, and appearance items.
– Products that have been modied to perform outside of specications without the prior written permission of EdgeStar.
–Products lost in shipment, or theft.
–Products sold AS IS or from an unauthorized reseller.
–Products that have had their serial numbers removed or defaced. Products with serial numbers that have been invalidated.
–Damage to personal property from use of product.
–Replacement of repair of household fuses, circuit breakers, wiring, or plumbing.
OBTAINING WARRANTY SERVICE:
If you believe your product is defective, contact EdgeStar Customer Support for troubleshooting assistance and warranty service at
www.edgestar.com or 1-866-319-5473. Before contacting EdgeStar, have your serial number and proof of purchase available. Once an
EdgeStar authorized representative has conrmed that your product is defective and eligible for warranty service, the product must be
returned to an EdgeStar repair facility. The purchaser is solely responsible for prepaying all shipping related costs to and from the repair
facility. EdgeStar is not responsible for damage resulting from shipper mishandling or improper packaging. Do not return a defective
product to the place of purchase. Products received without a return authorization number will be refused.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS
REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. NEITHER THE MANUFACTURER
NOR ITS DISTRIBUTORS SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE
DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROFITS, OR ANY OTHER DAMAGE
WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. IN NO EVENT AND UNDER NO CIRCUMSTANCE OF ANY TYPE OR
KIND SHALL THE SELLER, MANUFACTURER AND/OR DISTRIBUTOR BE LIABLE FOR ANY REASON, UNDER ANY THEORY, FOR
MORE THAN THE BASIC COST OF THE PRODUCT TO THE PURCHASER OR END USER. SOME STATES DO NOT ALLOW THE
EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.

EDGESTAR.COM V3.0 05262023