EDIFIER W800BT User manual

www.edier.com
W800BT
Bluetooth® Stereo Headphones

EN · Product Description and Accessories
USB charging cable
3.5mm audio cable
Audio connector
Volume + / next track
Volume - / previous track
Indicator light
Multi-function button
Charging port

■ Operational Guide
● Charge
During using, if only red light ashes, it indicates the headphones are at
low battery level, please use them after fully charged.
Red light steady lit = charging Red light o =fully charged
Rated input: 5V 500mA
Warning: The rechargeable batteries that provide power for this product
must be disposed properly for recycling. Do not dispose of batteries in
re to prevent an explosion.
If the product with lithium battery has not been usedfor long periods
of time, pleasecharge itat least once per 3 months.

● Bluetooth Connection
1. When powered on and not connected, press and hold the
multi-function button for 2 seconds until the red and blue light ashes
alternately, then the headphones enter pairing state.
2. When powered o, press and hold the multi-function button for
approx. 5 seconds until the red and blue light ashes alternately, then
the headphones enter pairing state;
3. Set your mobile phone to search for and connect to “EDIFIER W800BT”,
after pairing is successful, the blue light will ash slowly.
● Connect to Two Bluetooth Devices Simultaneously
1. Pair the headphones with the rst device;
2. Restart the headphones: press and hold the multi-function button for
5 seconds to enter pairing state and pair with the second device;
3. Operate the rst device to pair with the headphones again, then they
are successfully connected to two devices simultaneously.
● Power ON/OFF
Power on: press and hold for 3 seconds
Power o: press and hold for 3 seconds

■ Functional Operation Instructions
● Music Playback
● Call
•Clear pairing records: when powered on and not connected, press
and hold the “+” and “-” buttons simultaneously for 5 seconds, wait
until the blue light ashes rapidly, then the pairing records have been
cleared.
Accept a call: single press
End a call: single press
Decline a call: press and hold
Volume +:
single press
Next track:
press and hold
Volume -:
single press
Previous track:
press and hold
Pause/play:
single press
Voice assistant:
double press

Red light instead of blue light ashes.
• The headphones are at low battery level, please recharge the headphones.
Red light is o during charging.
• Ensure the charging device is correctly connected with the headphones.
•When the headphones have not been used for long periods of time,
the battery will enter sleep state, it needs to charge about 30 minutes
and then the red light will be lit.
No sound
•Check if the headphones are operating.
•Check if the headphones volume is at an appropriate level.
•Check if the headphones are correctly connected with mobile phone.
•Check if the headphones are operating within a normal working range.
Call quality of the headphones are not good.
•Check if mobile phone is in an area with strong signal.
•Please ensure the headphones are within eective distance (10m)
and no obstacle between the headphones and mobile phone.
When playing music, cannot control pause/play/previous track/
next track via headphones.
•Please ensure the paired device support AVRCP (Audio/Video
Remote Control Prole) prole.
■ FAQs

During using, please read the following suggestions carefully.
•Keep the product away from humid places to avoid aecting internal
circuit. Do not use the product during intense exercise or with much
sweat to prevent sweat from dropping into the product to make
damage.
•Do not put the product in places exposed to sun or with high
temperature. High temperature will shorten service life of electronic
components, damage battery and deform plastic components.
•Do not put the product in cold places to avoid damaging internal
circuit board.
•Do not dismantle the product. Non-professional personnel may
damage the product.
•Do not drop, strongly vibrate, strike the product with hard object to
avoid damaging internal circuit.
•Do not use drastic chemicals or cleaner to clean the product.
•Do not use sharp objects to scratch product surface to avoid
damaging shell and aecting looking.
If the product cannot operate properly, please send it to your qualied
maintenance agency.
■ Maintenance

EDIFIER International Limited
www.edier.com
2019 Edier International Limited. All rights reserved.
Printed in China
NOTICE:
For the need of technical improvement and system upgrade,
information contained herein may be subject to change from time
to time without prior notice.
Products of EDIFIER will be customized for dierent applications.
Pictures and illustrations shown on this manual may be slightly
dierent from actual product.
Picture for reference only, actual product prevails.