Edimax Wireless LAN Access Point User manual

Wireless LAN Access Point
User’s Manual

Table of Contents
Chapter 1 Introduction.........................................................1
1.1 Package Contents.........................................1
1.2 Features........................................................2
1.3 Specifications................................................2
1.4 Physical Description......................................3
Chapter 2 W ireless L AN Access Point Connection..........5
Chapter 3 W ireless L AN Access Point Configuration......6
3.1 Getting Started..............................................6
3.2 Configuring the Access Point......................10
3.2.1 Status and Information....................10
3.2.2 Wireless Setting..............................10
3.2.3 Advanced Setting............................18
3.2.4 Security...........................................21
3.2.5 Radius Server.................................30
3.2.6 MAC Address Filtering....................33
3.2.7 System Utility....................................35
3.2.8 Configuration Too.............................37
3.2.9 Firmware Upgrade...........................39
3.2.10 Reset...............................................40
Chapter 4. Troubleshooting...............................................41

Introduction
Chapter 1 Introduction
This product is an access poi nt for IEEE 802.11g/b 2.4GHz
wireless networ k. You can use this access point to build up a
wireless LAN.
The pr oduct supports WEP, ESSID and MAC address filter
functi ons to consolidate the wireless network security. With
ESSID authentication, 64/128 bit WEP encr yption and MAC
address filtering you can prevent unauthorized wireless
stations from accessing your wireless networ k.
The pr oduct’s dipole antenna is detachable byconnecti ng to a
RP-SMA connector. Users can install a high gain antenna to
the connector for better networ klinkqualityso that you can
build wireless network with more flexibility.
This product provides easyto use user interface and allows
users to configuring from web browser. Also it integrates
DHCPserver to provide multiple wireless and wired users to
get their IP address automatically. With the versatile of
features, this pr oduct is the best choice for you to integrate
your wireless and wired networ kseamlessl y.
1.1 Package Contents
The Access Point i ncludes the following items:
yOne Access Point
yOne Power Adapter
yOne User’s Manual
1

Introduction
1.2 Features
yComplies with the IEEE 802.11g/b 2.4GHz specificati on.
yHigh data r ate 54, 11, 5.5, 2 and 1M bps networkspeed.
ySeamlessl yintegrate wireless and wired Ethernet LAN
networ ks.
yProvides an i nternal 5-Port Fast Ethernet Switch for
wired Ethernet connection.
yAuto rate fallbackin case of obstacles or interferences.
yProvide 64/128-bit WEP Data Encr yption function to
protect the wireless data transmissions.
yBuilt-inDHCPserver supports auto IP addresses
assignment.
ySupports Web-based configuration.
1.3 Specifications
yStandards: IEEE 802.11g/b (Wirel ess), IEEE 802.3
(Wired)
yData Rate: 54/11/5.5/2/1Mbps auto fallback
ySecurity: 64/128-bit WEP Data Encryption
yFrequencyBand: 2.400~2.4835GHz (Industrial Scientific
Medical Band)
yRadio Technology: Direct Sequence Spread Spectrum
(DSSS)
yAntenna: External detachable dipole antenna (with RP-
SMA connector)
yConnectors: 10/100Mbps RJ-45 x 1
yPower: 12VDC, 1A
yTransmit Power: 18dBm (Typical)
yLEDs:Power, LAN Link/Activity, Wireless Activity
yDimension: 30(H) x 187(W) x 100(D) mm
yTemperature:
Operati ng: 32~ 131°F (0~55°C)
Storage: - 4~158°F(-20~70°C)
yHumidity: 10- 90% (Non-condensing)
yCertification: FCC,CE
2

Introduction
1.4 Physical Description
Front Panel
On the Access Point’s front panel there ar e LED lights that
inform you of theAccess Point’s current status. Belowis an
explanation of each LED.
LED Color Status Description
Lit Power is supplied.
Power Green Off No Power.
Flash
A
ntenna is transmitting or
receiving data.
Wireless
Activity Green Off Antenna is not
transmitting or receiving
data.
On A validlinkis
established.
Flash It is transmitting or
receiving data.
LAN
Link/Activity Green
Off No link is established.
Back Panel
Access Point’s connecti on ports are located on the back panel.
Belowis the descripti on of each connection port.
3

Introduction
yAntennaConnector
This round connection is standard R everse SMA connector
where any antennas with Reverse SMA connector can
connect to the Access Point.
yDC Adapter Port
Insert the power jackof the power adapter into this port.
yLAN Port
The Access Point’s LAN port is where you connect to your
LAN’s networ kdevices.
yReset
The Reset button allows you to do one of two things.
1) If problems occur with your Access Point, press the reset
button with a pencil tip (for less than 4 seconds) and the
Access Point will re-bootitself, keeping your original
configurations.
2) If problems persist or you experience extreme problems
or you forgot your password, press the reset button for
longer than 4seconds and theAccess Point will reset
itself to the factor y default setti ngs (warning: your original
configurations will bereplaced withthefactory default
settings).
4

W ireless L AN AP Connection
5
Chapter 2 Wireless LAN AP Connection
1. Locate an optimum location for the W ireless LAN
Access Point.
The best location for your Access Point is usually at the
center of your wireless network, with line of sight to all of
your mobile stati ons.
2. Connect the W ireless LAN Access Point to your
router, hub or switch.
Connect one end of standard UTP cable to the Access
Point’s LAN Port and connect the other end of the cable
toa switch, arouter or ahub.TheAccessPoint will then
be connected to your existed wired LAN Networ k.
3. Connect the DC Po wer Ad apter to the W ireless LAN
Access Point’s Power Socket.
Only use the power adapter supplied with the Access
Point. Using a different adapter may damage the product.
The Hardware Installation is complet e.

W ireless L AN AP Configuration
Chapter 3 Wireless LAN AP Configuration
3.1 Getting Started
This Access Point provi des web-based configuration tool
allowing you to configure fr om wired or wireless stations.
Follow the instructions below to get started configuration.
From Wired Station
1. Make sure your wired station is in the same subnet with
the Access Point.
The default IP Address and Sub Maskof the Access Point
is: Default IP Address: 192.168.2.1
Default Subnet: 255.255.255.0
Configureyour PC to bein thesame subnet with the
Access Point.
1a) Windows 95/98/Me
1. ClicktheStart button and sel ect Settings, then click
Control Panel. The Control Panel window will appear.
2. Double-clickNetwork icon. The Network window will
appear.
3. Check your list of Network Components. If TCP/IP is not
installed,click theAdd button to install it now. If TCP/IP is
installed,gotostep 6.
4. In the Network Component Type dialog box, select
Protocol and clickAdd button.
5. In the Select Network Protocol dialog box, select
Microsoft and TCP/IP and then click the OK button to
startinstalling theTCP/IP protocol. You may need your
Windows CD to complete the installation.
6. After installing TCP/IP, gobacktotheNetwork dial og
box. Select TCP/IPfromthe list of Network
Components and then click the Pr operti es button.
6

W ireless L AN AP Configuration
7. Checkeach of the tabs and verifythe following settings:
yBindings: Check Client for Microsoft N etworks and File
and printer sharing for Microsoft Networks.
yGateway: All fields are blank.
yDNSConfiguration: Select DisableDNS.
yWINSConfiguration: Select DisableWINSResolution.
yIP Address: Select Specify an IP Address. Specify the
IP Address and Subnet M askas following example.
9IP Address: 192.168.2.3 (anyIP address within
192.168.2.2~192.168.2.254 is available, do not
setup 192.168.2.1)
9Subnet Mask: 255.255.255.0
8.Rebootthe PC.Your PC will now havethe IP Address you
specified.
1b) Windows2000
1. ClicktheStart button and sel ect Settings, then click
Control Panel. The Control Panel window will appear.
2. Double-clickNetwork and Dial-up C onnections icon. In
the Network and Dial-up Connection wi ndow, double-
clickLocal Ar ea Connection icon. The Local Area
Connection window will appear.
3. In the Local Area Connecti on window, clickthe
Properties button.
4. Check your list of Network Components. You should see
Internet Protocol [TCP/IP] on your list. Select it and
clickthePr operti es button.
5. In the Internet Protocol (TCP/IP) Properties window,
select Use the following IP address and specify the IP
Address and Subnet maskas following.
9IP Address: 192.168.2.3 (anyIP address within
192.168.2.2~192.168.2.254 is available, do not
setup 192.168.2.1)
9Subnet Mask: 255.255.255.0
6. ClickOK toconfirm thesetting.Your PC will now have
the IP Address you specified.
7

W ireless L AN AP Configuration
1c) WindowsNT
1. ClicktheStart button and sel ect Settings, then click
Control Panel. The Control Panel window will appear.
2. Double-clickNetwork icon. The Network window will
appear. Select the Protocol tab fromthe Network window.
3. Checkif the TCP/IP Protocol is on your listofNetwork
Protocols. If TCP/IP is notinstalled, click theAdd button
toinstall itnow.If TCP/IP is installed,go to step 5.
4. In the Select Network Protocol window, select the
TCP/IP Protocol and clickthe Ok button to start
installing the TCP/IP protocol. You may need your
Windows CD to complete the installati on.
5. After you install TCP/IP, go back to the Network window.
Select TCP/IP from the list of Network Protocols and
then click the Properties button.
6. Checkeach of the tabs and verifythe following settings:
yIP Address: Select Specify an IP address. Specifythe
IP Address and Subnet M askas following example.
9IP Address: 192.168.2.3 (anyIP address within
192.168.2.2~192.168.2.254 is available, do not setup
192.168.2.1)
9Subnet Mask: 255.255.255.0
•DNS: Let all fields are bl ank.
•WINS:Let all fields are blank.
•Routing: Let all fields are blank.
7. ClickOK toconfirm thesetting.Your PC will now have
the IP Address you specified.
2. Enter 192.168.2.1 from Web Browser to get into the
Access Point’s configurati on tool.
3. Ascreen will be popped up andrequest youtoenter user
name and password. The default user name and
password is as follows. UserName:Admin
Password: 1234
8