Edimax ES-5500G V2 User manual

1
ES-5500G V2 / ES-5800G V2
Quick Installation Guide
07-2012 / v1.0

2
COPYRIGHT
Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or by
any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission from Edimax Technology Co.,
Ltd.
Edimax Technology Co., Ltd. makes no representations or warranties, either
expressed or implied, with respect to the contents hereof and specifically
disclaims any warranties, merchantability, or fitness for any particular purpose.
Edimax Technology Co., Ltd. reserves the right to revise this publication and to
make changes from time to time in the contents hereof without the obligation to
notify any person of such revision or changes.
The product you have purchased and the setup screen may appear slightly
different from those shown in this QIG. The specification is subject to change
without notice. Please visit our web site www.edimax.com for the update. All
brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
Edimax Technology Co., Ltd.
Add: No. 3, Wu‐Chuan 3rd Rd., Wu‐Ku Industrial Park, New Taipei City, Taiwan
Tel: +886‐2‐77396888
Email: [e-mail]

3
PRODUCT INTRODUCTION
Model no.:
ES-5500G V2: 5-Port Gigabit Desktop Switch
ES-5800G V2: 8-Port Gigabit Desktop Switch
Package Contents
Before you start using this router, please check if there is anything missing in the
package, and contact your dealer to claim the missing item(s):
Gigabit Desktop switch (1 pcs)
User manual guide (1 pcs)
Power Adapter (1 pcs)
Front Panel
Please refer to the following description for the front panel:
ES-5500G V2
ES-5800G V2
LED Definition:
LED Name
Light
Status
Description
PWR
On
Switch on and correctly powered
Off
Switch not powered or not correctly powered
LNK/ACT
On
The port connected
Off
The port not connected
Flashing
The port is activating and transferring /receiving
data.

4
Back Panel
ES-5500G V2
ES-5800G V2
1. Operating Environment
This switching hub must be installed and operated within the limits of
specified operating temperature 0~40°C(32~104°F) and humidity (10~90%
Non-condensing).
˙Do not place objects on top of the unit.
˙Do not obstruct any vents at the sides of the unit.
˙Do not position the unit near any heating source such as heater, radiator or
direct exposure to sun.
Prevent entering of water and moisture into the unit, If necessary, use
dehumidifier to reduce humidity.
2. Connecting to network devices
The RJ-45 ports on the switch support Auto-MDI/MDI-X function which allows
using straight-thought crow-over type cables to connect this switch to
workstation or hub.
Connect on end of the network cable to the RJ-45 port on the rear panel, and
connect the other end of the network cable to the RJ-45 port on the network
device. Follow the same procedure to connect all the RJ-45 ports of the switch.

5
The UTP network cables must comply with EIA/TIA 568 specifications and
Category 5 standard for data transmission. Maximum length using UTP cable,
between the switch and connected devices is 100 meters (300ft).
Once the network cable is connected to both ends and the attached network
device is powered on, the green LNK/ACT LED should be lit.
3. Connecting the power
Connect the power adapter to the power connector of the unit; the green Power
LED on the front panel should be lit.

6
Trouble Shooting
1. Power LED is not lit
Check if the power cord is properly connected to the external power adapter
and the power outlet. Make sure the DC power jack is firmly plugged into the
power socket of the switch.
2. Link/Activity is not lit when connect to devices
˙Check the power switch of the network device attached to the switch; make
sure it is turned ON.
˙Check the network cable; make sure it is properly connected to the switch
and the network device.
˙Check the network cable; make sure the UTP cable comply with EIA/TIA 568
and Category 5 specification.
[!] Contact your dealer if problem persist.

7
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This device and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the authority to operate equipment.
CE Mark Warning
This is a class B product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.