Edimax GS-5654LX User manual

GS-5654LX, GS-5654PLX V2
Quick Installation Guide
04-2023 / V1.1

Contents
I. Product Information.................................................1
I-1. Package Content ..................................................................1
I-2. Hardware Overview .............................................................2
I-3. LED Status.............................................................................3
II. Installation ..............................................................5
II-1. Physically Setup....................................................................5
II-2. Connection...........................................................................6
III.Web-based Configuration Utility ..............................8
IV. More Information..................................................10
V. Safety Instructions .................................................10

1
I. Product Information
GS-5654LX: 54-Port Gigabit Web Smart Switch with 6 SFP+ 10G Ports
GS-5654PLX V2: 54-Port Gigabit PoE+ Long Range Web Smart Switch with
6 SFP+ 10G Ports
I-1. Package Content
GS-5408PLG V2
Power Cord
Rack-Mount Kit
GS-5424PLC V3
Quick Installation
Guide
Console Cable
GS-5654LX or GS-5654PLX V2

2
I-2. Hardware Overview
GS-5654LX:
GS-5654PLX V2:
Console Port
AC Power Jack
DC Fan
SYS ALM: System Alarm LED
SYS: System LED
PWR: Power LED
Gigabit Port (1~48)
Reset Button
10 Gigabit SFP+
Port (49~54)
SYS ALM: System Alarm LED
PoE Max: Over PoE Max Power Alarm LED
Gigabit PoE Port
(1~48)
Reset
Button
Indicators Slide
Switch
SYS: System LED
PWR: Power LED
10 Gigabit SFP+
Port (49~54)
Console Port
AC Power Jack

3
I-3. LED Status
GS-5654LX
Function
Color
Status
Description
PWR
Green
On
Power on
Off
Power off
SYS
Green
On
Power on
Blinking
System is booting up
Off
Power off
SYS ALM
Red
On
System failure
Off
Device in good condition
Link/Act
(1~48 Port)
Green
On
Link at 1000Mbps
Blinking
Sending or receiving data
Off
Port disconnected or link fail
Amber
On
Link at 10/100Mbps
Blinking
Sending or receiving data
Off
Port disconnected or link fail
10 G
SFP+ Port
(49-54 Port)
Blue
On
Link at 10Gbps
Blinking
Sending or receiving data
Off
Port disconnected or link fail
Green
On
Link at 1Gbps
Blinking
Sending or receiving data
Off
Port disconnected or link fail

4
GS-5654PLX V2
Function
Color
Status
Description
PWR
Green
On
Power on
Off
Power off
SYS
Green
On
Power on
Blinking
System is booting up
Off
Power off
SYS ALM
Red
On
System failure (Overheat, wrong
voltage)
Off
Device in good condition
PoE Max
Green
On
Over PoE max. power
Off
Not over PoE max power
10 G
SFP+ Port
(Port 49~54)
Blue
On
Link at 10Gbps
Blinking
Sending or receiving data
Off
Port disconnected or link fail
Green
On
Link at 1000Mbps
Blinking
Sending or receiving data
Off
Port disconnected or link fail
Link/Act or PoE
Indicators
Slide Switch
Link/Act
(Left)
Show Link/Act network
connection status (Port 1 ~48)
PoE
(Right)
Show PoE connection status (Port
1~48)
Link/Act
(Left )
Green
On
Link at 1000Mbps
Blinking
Sending or receiving data
Off
Port disconnected or link fail
Amber
On
Link at 10/100Mbps
Blinking
Sending or receiving data
off
Port disconnected or link fail
PoE
(Right)
Green
On
Feeding power to PoE devices
Off
PoE function is not active

5
II. Installation
Read the following topics and perform the procedures in the correct order.
Incorrect installation may cause damage to the product.
II-1. Physically Setup
There are two ways to physically set up the switch. No matter how you
installed the switch, please keep it with good ventilation.
1. Desktop Placement: Attach the supplied rubber feet to the recessed areas
on the bottom of the switch. Place the switch on a flat surface and keep it
with good ventilation.
2. Rack-Mount Installation: You can mount the switch in any standard size,
19-inch (about 48 cm) wide rack with 1 Rack Unit (1U) of space, which is
1.75 inches (4.45 cm) high.
First, align the mounting brackets with the mounting holes on the switch’s
side panels and secure the brackets with the screws.

6
Then secure the switch on the equipment rack and keep it with good
ventilation.
II-2. Connection
1. Power on: Connect the power cord to the switch and the power outlet.
The switch is powered by the 100-240VAC 50/60Hz external high-
performance power supply. (Note: Make sure the PWR LED is green.)
2. Uplink: Plug the SFP/SFP+ cable into the SFP/SFP+ slot (Note: Make sure
that the LED is blue (SFP+), green or amber (SFP)) or plug the standard
Cat5e or above Ethernet cable into the LAN port (Note: Make sure that the
LED is green or amber) and connect it to another switch.
3. Connect devices: Plug the standard Cat5e or above Ethernet cable into the
LAN port and connect to any networking device with an Ethernet port.
(Note: Make sure that the "LAN" Link/Act LED is green or amber.) The
hardware installation is complete!

7
4. Connect a computer: Connect your computer with the switch and get
ready for web-based configuration with following “Section III Web-based
Configuration Utility”.
1. Power on
3. Connect devices
2. Uplink to another
switch
4. Connect to
a computer

8
III.Web-based Configuration Utility
This section describes how to navigate the web-based switch configuration
utility through web browser. Be sure to disable any browser pop-up blocker.
Browser Restrictions
If you are using older versions of Internet Explorer, you cannot directly use
an IPv6 address to access the device. You can, however, use the DNS
(Domain Name System) server to create a domain name that contains the
IPv6 address, and then use that domain name in the address bar in place
of the IPv6 address.
If you have multiple IPv6 interfaces on your management station, use the
IPv6 global address instead of the IPv6 link local address to access the
device from your browser.
Launching the Configuration Utility
1. Connect your computer with the switch then open a web browser.
2. Enter the IP address of the switch you are configuring in the address bar
on the browser (factory default IP address is 192.168.2.1) and then press
Enter. Please make sure that your computer's IP address is in the same
subnet as this switch. The default IP address is an IP address in the range
of 192.168.2.X (X=2-254). You can modify the IP address of your computer
if you need.
Default IP
192.168.2.1
Default User Name
admin
Default Password
1234