Edsal Muscle Rack UR184884WR6 User manual

Safety Instructions
Safety Instructions
Safety Instructions
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a
possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not
included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY
PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the
heavier loads on the bottom. Use care when working with metal parts.
Heavy Duty Shelving MODEL NUMBER
UR184884WR6
D - Bottom
Post
UR184884WR6 6 Shelf
UR184884WR6 6 Shelf
UR184884WR6 6 Shelf -
-
-84”h x 18”d x 48”w
84”h x 18”d x 48”w
84”h x 18”d x 48”w
Description
A - Beams
B - Braces
C - Top Post
D - Bottom Post
E - Wire Deck
F - Coupler
Qty.
12
12
4
4
6
4
Part Number
RUBE 4702
RUBE 1702
RCPT3605S
RCPT4805S
WD1848
RMPC0409
Part Size
47 7/16”
17 7/16”
36”
48”
18” x 48”
N/A
General Instructions
General Instructions
General Instructions
Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used
on the beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block
of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and
fully engaged.
Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel
free to contact our Muscle Rack manufacturing facility at, [phone] and request customer service.
We can also be reached on the internet at the following email address : [email protected].
To obtain replacement parts, please provide the following information :
- Model # - Part # & Description - Location Purchased - Date Purchased
Consumer Products Division
Edsal Manufacturing Company
Made In China
4400 South Packers Avenue
Chicago, IL 60609 www.edsal.com
A - Beams
B - Braces
C - Top
Post
E - Wire Deck
F - Post Coupler

Assemble two (2) 48” bottom post with one (1) brace. Skipping
one slot from the bottom of the post (see figure A), place the
rivets into post with the slot pointing down, and with the shelf
ledge of the brace facing up (see figure B). Tap lightly to seat
rivets. Repeat with two (2) 48” bottom post and one (1) brace.
Assemble the two (2) end units with two (2) beams (see figure
C). Skip one hole from the bottom of post, tap lightly to seat
rivets.
Assembly Instructions for UR184884WR6
Assembly Instructions for UR184884WR6
Assembly Instructions for UR184884WR6
Continue working by adding the second level using two
(2) beams and two (2) braces in the post slots of your
desired location. Again place the rivets of the beams
and braces into the post slots with the shelf ledge facing
up and tap lightly to seat the rivets.
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
Continue by adding the fourth, fifth and sixth level to the
unit using six (6) beams, six (6) braces. After each level
is in place, tap lightly to properly seat the rivets. Finally
add the wire decking to each level using one (1) piece
per level.
Step
1
Step
2
Step
3
Step
4
Figure A
Figure B
Figure C
Shelf Ledge
Brace
Bottom
Post
Tap Lightly
Beam
Figure C
Note:
Post are
directional.
The slot
must point
down. Post Slot Points Down
Note:
Post are directional. The slot
must point down.
Top Post
Figure D
Post Coupler
Bottom Post
Assemble the four (4) 36” top post to the bottom post by
using four (4) of the post couplers. Place the couplers on
the top of the bottom post, and the bottom of the top post
and tap down to properly seat (see figure D). Continue
by adding the third level of beams and braces just below
the post couplers. Again tap lightly to seat the rivets.
Wire Decking