Teknion Dossier Operating and maintenance instructions

ZJNU, ZJNV, ZJNW, ZJNX, ZJNY, ZJNZ Part and Product Identification
A - Worksurface
(C56-0010) x1
For Customer Support please contact
[email protected]
dossier
Section:
Description:
Page No:
Date:
Rev. No:
DOS_009_G01
1 of 7
Sept 2013
0
B1 - U Leg
(X58-0019) x1
B2 - Leveler Cover
(A25-0335) x2
C1 - Flush Plate
(D56-0006) x1
C2 - Screw
(E57-0023) x8
C - (X56-0001) x3 Optional for
ZJNU, ZJNV, ZJNW
NOTE: Run-Off with U-Leg - Centered
Modesty, Flush Credenza Conection
(ZJNV), and Standard Desk with Partial
Modesty (ZJSP) shown as an example.
B
A
B - (X58-0021) x1
B3 - Leveler
(D06-4065) x2
B4 - Screw
(E57-0042) x9
D1
E - #8 X 2 1/2" Flat Head Wood Screw
(SC065) x 3
Optional for ZJNN, ZJNM, ZJNO
D - Modesty Kit x1
Optional for ZJNC, ZJNI, ZJNM, ZJNO only
D1 - Modesty x1
D2 - Modesty Bracket
(D56-0004) x2
D3 - Modesty Bracket Screws
(D57-0002) x8
D4 - Cam
(B57-0002) x4
D5 - Titus Shaft
(B57-0001) x4
D
ZJSP

STEP 2: Flip Worksurface up-side-down. Place U-Leg onto the cut-out of the Worksurface as
shown.
STEP 1: Insert Leveler Cover into Legs and Secure with Levelers.
dossier
Section:
Description:
Page No:
Date:
DOS_009_G02
2 of 7
Sept 2013
U-LEG ASSEMBLY ATTACH U-LEG
A
B2
B1
B3
B1
A
Side View
Detail View
B1

STEP 4: Please insert Titus Shafts into the bottom of the Worksurface.
NOTE: Centered Modesty shown as an example.
STEP 5: Insert Modesty in the Titus Shafts as shown.
dossier
Section:
Description:
Page No:
Date:
DOS_009_G03
3 of 7
Sept 2013
SECURE U-LEG INSERT TITUS SHAFTS
ATTACH MODESTY
B4
STEP 3: Fasten U-Leg Frame and Worksurface with Screws provided.
NOTE: Please skip to Page 5 Step 9 if Modesty is NOT specified.
D1
D5
NOTE: Centered Modesty
shown as an example.
Detail View

STEP 7: Attach Modesty Brackets to Worksurface and Modesty equally.
NOTE: Installers to determine locations to attach Modesty Brackets. Location of Brackets
should not interfere with previously installed Cams.
STEP 6: Insert Cams into Modesty and rotate them to secure Modesty in place.
dossier
Section:
Description:
Page No:
Date:
DOS_009_G04
4 of 7
Sept 2013
SECURE MODESTY ATTACH MODESTY BRACKET
D2
D4
NOTE: Installers to determine
locations to attach Modesty
Brackets. Location of Brackets
should not interfere with
previously installed Cams.

STEP 9: Fasten Flush Plates under the Desk Worksurface.
NOTE: Please refer to Installation Guide DOS_007a for Overlap Mount, and DOS_004a for
Spacer Mount.
STEP 8: Fasten Modesty Brackets to Worksurface and Modesty as shown.
dossier
Section:
Description:
Page No:
Date:
DOS_009_G05
5 of 7
Sept 2013
SECURE MODESTY BRACKETS ATTACH FLUSH PLATE
Underside View
Side View
C1
C2
C2 C1
ZJSP Desk Worksurface
D3
Detail View
ZJSP Desk Worksurface

STEP 11: Fasten Run-Off with Flush Plate as shown.STEP 10: Lay Run-Off onto Flush Plate, and align with Desk as shown on bottom View.
dossier
Section:
Description:
Page No:
Date:
DOS_009_G06
6 of 7
Sept 2013
ATTACH RUN-OFF SECURE RUN-OFF
C2
Underside ViewUnderside View
Bottom View

STEP 12: Use leveler to make sure the Run-Off and Desk are leveled. Adjust Levelers under Post Leg if necessary.
dossier
Section:
Description:
Page No:
Date:
Page No:
Date:
LEVEL RUN-OFF
Sept 2013
7 of 7
DOS_009_G07
Detail View