Eduard 73 376 User manual

1/4
B-17G interior S.A.
73 376
73 376
1/72 scale detail set for Revell kit • sada detailù pro model 1/72 Revell
ORIGINAL KIT PARTS
PÙVODNÍ DÍLY STAVEBNICE PHOTO-ETCHED PARTS
LEPTANÉ DÍLY PARTS TO BE REMOVED
DÍLY K ODSTRANÌNÍ FILL TMELIT
eduard
REMOVE
ODSTRANIT
OPTION
VOLBA
?
REPLACE
NAHRADIT
BEND
OHNOUT
GRIND
OBROUSIT
SYMETRICAL ASSEMBLY
SYMETRICKÁ MONTÁŽ
DRILL HOLE
VRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUING
POUŽÍT EXPRESS MASK NABARVIT PØED SLEPENÍM
56
75
76
66
65
6
27 77
71
26
68
2 pcs
34
35
plastic
plastic
2 sets
55
23
32
63
64
!
ball pen
HOW TO MAKE THE RELIEF ON
OPPOSITE - REVERSE -
OF THE PLATE
79
Kit part 1
Kit part 17
17
29
70
72
2 pcs
Kit part 19
67
78
58
Kit part 16

2/4 73 376
28 24
8
l = 3,9mm
l = 2,7mm
plastic
2 pcs plastic
= 0,8mm
= 0,8mm
7
7
7
4 pcs
4 pcs
25
24, 28
22 5
18a
3
33
3 pcs
Kit part 46
74
20
12
14 18b
13
15
19
44
79
2 sets
4
Kit part 16
30 31
21 16
24, 28
21
16
Kit part
1
2
11
10
9
Kit part 21
Kit part 20
Kit part 67

3/4 73 376
© EDUARD M.A. 2010 www.eduard.com Made in Czech Republic
73
l = 5mm
3 pcs plastic
= 3mm
43
36
80
48
46
52
37
51
82
54 45
40
49
41
62
38
39
69
73
43
36
3 pcs plastic
= 3mm
59
50
50, 59
4 pcs
80
48
61 42
82
45
51
54
40
41
47
l = 5mm
Kit part 63
Kit part 13
2 pcs plastic
= 3mm
l = 5mm
53

2. Do not inadvertently place etched componets on an
unwanted surface. Attempts to remove will result in
damage to your part.
2. Nepokládejte samolepící díly na volné plochy. Pokud
je omylem pøilepíte, pøi pokusu o odlepení dojde k
poškození dílu.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na èásti dílù, na kterých je naneseno lepidlo.
1. Separate the etched components from their frames on the
protective paper. Removal from the paper is done only after
separation of the parts from the frames.
1.Samolepící díly oddìlujte od rámeèku na podkladovém
papíøe. Po oddìlení je sejmìte z krycího papíru.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za èásti, na kterých
není nanesené lepidlo.
5. Lightly place the component in the desired location and
position. Adjust as required. The component will by
permanently affixed when pressed onto its intended
location, its location can be adjusted.
5. Díl lehce položte do pozice, ve které má být nalepen.
Upravte pøesnou pozici a pøimáèknìte. Díl dokonale pøilne
až po pøimáèknutí, pøed pøimáèknutím lze dílem opatrnì
manipulovat.
4/4 73 376
© EDUARD M.A. 2010 www.eduard.com Made in Czech Republic
PARTS WITH GLUE . DÍLY OPATØENÉ LEPIDLEM
41
60
Kit part 171
Kit part 172
57
81
2 pcs
© EDUARD 2010 Made in Czech Republic
1
2
3
456
78 9 10 11 12
13 14 15 16 17 18
19 20 21 22 23
24 25 26 27 28 29
30 31
32 33
1 / 72 SS 376 + 73 376 B-17G interior
18b
17
4
7
32 33