Eiki EZtrol 200L User manual

EZtrol
200L
L
Manual

i
About US
LSE Controls builds products that address the practical problems of
simplified data projector operation. We do this based on our over 30
years of experience in the Audio-Video integration field. We develop
products to solve problems that we face. Because of this we are
committed to designing and building products that are not going to fail
in the field and that are adaptable to a technical environment that
changes at breakneck speed.
We also truly understand the frustration that comes from having a
ten-minute question take two weeks to get answered, that is why we
respond to technical support questions within 24 hours. Our products
are designed to provide affordable, reliable control devices that can
be used as a common look-and-feel system across an organization
for many years.

i
i
Table of Contents
EZtrol 200L Parts List 1
Items Provided by Installer 2
Preloaded Eiki Code 3
Preloaded Timer 4
EZtrol 200L Layout 5
EZtrol 200L Software Installations 6
Programming EZtrol 200L 7-17
Labeling Buttons 18-19
Installing EZtrol 200L 20-24
EZtrol 200L Software Troubleshooting 25
EZtrol 200L Operation Troubleshooting 25

-1-
EZtrol 200L Parts List
• EZtrol 200L
• AC/DC Power Supply
• EZlink Hub
• 2 Screws
• Label Sheet

-2-
Items Provided by Installer
• DB 9 serial cable to connect your computer to EZtrol 200L
• Slotted screw driver
• Hex driver
• 2 pieces of standard Cat 5 cables to run between the EZtrol 200L and EZlink
Hub
• The control cable that comes with the projector or that was purchased from the
projector company
• DB 9 serial cable if connecting the NPC-1

-3-
Preloaded Eiki Code
EZtrol 200L is Preloaded with the RS232 commands for the
Eiki LC-X1100/LC-X986 data projectors
To select the following Eiki data projectors RS232 commands you must
Press button 8 down for 30 seconds. Keep pressing the button down and the
button will blink once then pause for about 3 seconds, then it will blink twice then
pause for 3 seconds. Each set of blinks represents the following drivers for EIKI
model projectors:
LC – X1100 = One Blink
LC – X986 = One Blink
LC – XNB4M = Two Blinks
LC – XNB4 = Two Blinks
LC – NB4 = Two Blinks
LC – NB4S = Two Blinks
LC – NB3EU = Three Blinks
LC – XG200 = Four Blinks
LC – XG100 = Four Blinks
LC – XM4 = Five Blinks
LC – SM4 = Five Blinks
LC – X4A = Six Blinks
LC – X4LA = Six Blinks
LC – X5L = Six Blinks
LC – SX1U = Seven Blinks
LC – SX1UL = Seven Blinks
LC – XT3 = Eight Blinks
L

-4-
Preloaded Timers
EZtrol 200L is preloaded with different timers that can be selected by pressing
button 9 down for 30 seconds. Keep pressing the button down and the button will
blink once then pause for about 3 seconds, then it will blink twice then pause for
3 seconds. Each set of blinks represents a different hour timer.
One hour = One Blink
Two hours = Two Blinks
Three hours = Three Blinks
Four hours = Four Blinks
Five hours = Five Blinks
Six hours = Six Blinks
Seven hours = Seven Blinks
Eight hours = Eight Blinks
Nine hours = Nine Blinks
No timer = Ten Blinks

-5-

-6-
EZtrol 200L software Installation
1. Using your web browser connect to
http://www.eztrol.com/softwareprograms_eztrol200.shtml
2. Then select EZtrol 200 Software from the menu
3. Save the file to your PC
4. Then install the program from your computer’s desktop

-7-
Programming EZtrol 200L
(Best viewed in 1024 x 768 or higher)
1. Connect your EZtrol 200L to your EZlink Hub by taking 2 standard cat 5
cables and places them between EZlink 1 on the hub and EZ 1 on the
control and the second cable to EZlink 2 of the Hub and EZ 2 of the
controller
2. Then take a DB9 female to a DB9 female cable and plug one end into RS-
232-2 and the other into your computer
3. Set the dip switches on the EZlink Hub see page 25
4. Connect the power supply to the EZlink hub .
5. Then choose which level of programming you will need
In this section we will explain the different ways to program the EZtrol 200L
Programming using a Saved file
1. Select EZloader 200L under LSE Controls by clicking on the start menu,
then all programs, then LSE Controls and select EZtrol 200
2. Select File
3. Then Open
4. Select saved file