EINHELL PRESSITO User manual

PRESSITO
Art.-Nr.: 40.204.60 I.-Nr.: 11017
13
DOriginalbetriebsanleitung
Hybrid-Kompressor
GB Original operating instructions
Hybrid compressor
FInstructions d’origine
Compresseur hybride
IIstruzioni per l’uso originali
Compressore ibrido
DK/ Original betjeningsvejledning
NHybrid-kompressor
SOriginal-bruksanvisning
Hybrid-kompressor
CZ Originální návod k obsluze
Hybridní kompresor
SK Originálny návod na obsluhu
Hybridný kompresor
NL Originele handleiding
Hybride compressor
EManual de instrucciones original
Compresor híbrido
FIN Alkuperäiskäyttöohje
Hybridikompressori
SLO Originalna navodila za uporabo
Hibridni kompresor
HEredeti használati utasítás
Hibrid-kompresszor
RO Instrucţiuni de utilizare originale
Compresor hibrid
GR Πρωτότυπες Οδηγίες χρήσης
Υβριδικός συπιεστής
PManual de instruções original
Compressor híbrido
HR/ Originalne upute za uporabu
BIH Hibridni kompresor
RS Originalna uputstva za upotrebu
Hibridni kompresor
TR Orijinal Kullanma Talimat
Hibrit kompresör
PL Instrukcjąoryginalną
Kompresor akumulatorowo-
sieciowy
RUS Оригинальное руководство по
эксплуатации
Гибридный компрессор
Anl_PRESSITO_SPK13.indb 1 16.09.2021 09:15:14

- 2 -
1a
1b
4
3
7
8
9
5
2
5 1
Anl_PRESSITO_SPK13.indb 2 16.09.2021 09:15:16

- 3 -
2 3
4 5
6 7
13c6
10
11
12
ab
4 2
7
8
9
10 14 15 16 11 12
Anl_PRESSITO_SPK13.indb 3 16.09.2021 09:15:18

- 4 -
8
17
9d 6
10
1 23
45
Anl_PRESSITO_SPK13.indb 4 16.09.2021 09:15:24

GB
- 15 -
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 10)
1. Danger! - Read the operating instructions to
reduce the risk of injury.
2. Caution! Wear ear-muffs. The impact of noi-
se can cause damage to hearing.
3. Beware of electrical voltage!
4. Beware of hot parts!
5. Store the batteries only in dry rooms with
an ambient temperature of +10°C to +40°C.
Place only fully charged batteries in storage
(charged at least 40%).
1. Safety regulations
The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
2. Layout and items supplied
2.1 Layout (Fig. 1-8)
1 Handle
2 Accessory storage compartment
3 Air hose
4 Air hose connection (blowing)
5 Compressed air hose with valve adapter
6 Battery pack (not supplied)
7 Bicycle adapter
8 Conical adapter
9 Adapter for ball valves
10 Selector switch for mains-powered mode/
battery-powered mode
11 Display
12 Selector switch for compressed air mode/
OFF/low-pressure blower mode
13 Air hose connection (suction)
14 “Reduce pressure” button
15 “Unit overpressure” button
16 “Increase pressure” button
17 Storage compartment for the power cable
2.2 Items supplied
Please check that the article is complete as
specied in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
• Open the packaging and take out the equip-
ment with care.
• Remove the packaging material and any
packaging and/or transportation braces (if
available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for
transport damage.
• If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suffocating!
• Air hose
• Bicycle adapter
• Conical adapter
• Adapter for ball valves
• Original operating instructions
• Safety instructions
3. Proper use
This device is intended for inating car, motorcyc-
le and bicycle tires as well as sports balls, water
balls, air mattresses and other similar items.
In addition the device is also intended for suctio-
ning volumes of air from objects with low pressu-
re, such as water balls, air mattresses and other
similar items.
Anl_PRESSITO_SPK13.indb 15 16.09.2021 09:15:43

GB
- 16 -
This device is not suitable for tires with very large
volumes, such as truck or tractor tires for examp-
le.
The equipment can be operated from the mains
power supply using the power cable or alterna-
tively in battery-powered mode using a suitable
rechargeable battery.
The equipment does not have a charging functio-
nality for the rechargeable battery.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse.The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Weight without battery ................. approx. 2.2 kg
Protection type............................................ IP X0
Protection class .......................................... II / 
Length of compressed air hose .... approx. 71 cm
Length of air hose ........................ approx. 31 cm
Data for mains-powered mode
Rated operating voltage and frequency
(mains-powered) .................... 220-240V ~ 50 Hz
Rating (compressor compressed air) ......... 90 W
Max. operating pressure
(compressor compressed air) .................. 11 bar
Theoretical suction rate
(compressor compressed air) ......... 21 liters/min
Output for compressed air at 4 bar ......... 10 l/min
Output for compressed air at 7 bar ........... 8 l/min
Rating (low-pressure blower) ..................... 90 W
Max. volumetric ow for suctioning
(low-pressure blower): .......................... 380 l/min
Max. volumetric ow for inating
(low-pressure blower): .......................... 400 l/min
Compressor idling speed ................... 3450 min-1
Blower idling speed .......................... 15000 min-1
Data for operation with a rechargeable
battery
Power supply (rechargeable battery) .... 18 V d.c.
Max. operating pressure
(compressor compressed air) .................. 11 bar
Theoretical suction rate
(compressor compressed air) ......... 21 liters/min
Output for compressed air at 4 bar ........... 9 l/min
Output for compressed air at 7 bar ........... 6 l/min
Max. volumetric ow for suctioning
(low-pressure blower): .......................... 370 l/min
Max. volumetric ow for inating
(low-pressure blower): .......................... 390 l/min
Compressor idling speed ................... 3450 min-1
Blower idling speed .......................... 15000 min-1
Danger!
Sound and vibration
The noise emission values were measured in ac-
cordance with EN ISO 3744.
LpA sound pressure level ..................... 71.5 dB(A)
KpA uncertainty ............................................. 3 dB
LWA sound power level ....................... 82.5 dB(A)
KWA uncertainty ............................................. 3 dB
Wear ear-muffs.
The impact of noise can cause damage to hea-
ring.
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect wor-
king order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever ne-
cessary.
• Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
• Damage to hearing if no suitable ear protec-
tion is used.
Anl_PRESSITO_SPK13.indb 16 16.09.2021 09:15:43

GB
- 17 -
Danger!
The electric power tool generates an electro-
magnetic eld during operation. Under certain
circumstances this eld may actively or passively
impede medical implants.To reduce the risk of
serious or fatal injuries, we recommend persons
with medical implants to consult their doctor and
the manufacturer of the medical implant prior to
using the equipment.
5. Before using the equipment
Before you connect the equipment to the power
supply make sure that the data on the rating plate
are identical to the supply voltage (if operating
from the mains power supply).
Before you connect the equipment to the power
supply make sure that the data on the rating pla-
te are identical to the data for the rechargeable
battery (if using a rechargeable battery for ope-
ration).
• Check the equipment for damage which may
have occurred in transit. Report any damage
immediately to the transport company which
was used to deliver the compressor.
• Make sure that the intake air is dry and dust-
free.
• Do not install the compressor in a damp or
wet room.
• The compressor may only be used in suitable
rooms (with good ventilation and an ambient
temperature from +5 °C to 40 °C).There must
be no dust, acids, vapors, explosive gases or
inflammable gases in the room.
• The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor
in areas where work is conducted with spray-
ed water.
• Operate the equipment only on a firm, level
surface.
Warning! When using the equipment to inate
objects, check the information and safety instruc-
tions provided by the manufacturer.
5.1 Charging the LI battery pack (Fig. 2, 9)
1. Remove the battery pack (6) from the handle,
pressing the pushlock button (a) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(d) into the socket outlet.The green LED will
then begin to ash.
3. Push the battery pack (6) onto the battery
charger (d).
In section 10 (Charger indicator) you will nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
• voltage at the power socket
• whether there is good contact at the charging
contacts of the charging unit.
If the battery pack still fails to charge, send
• the charger and charging adapter
• and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.2 Battery capacity indicator (Fig. 2)
Press the button for the battery capacity indicator
(b). The battery capacity indicator (c) will indicate
the charge status of the battery by means of 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
Anl_PRESSITO_SPK13.indb 17 16.09.2021 09:15:43

GB
- 18 -
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
6.1 Changing between mains/battery operati-
on and compressor compressed air/low-
pressure blower operation (Fig. 7)
To change over between mains-powered and
battery-powered operation, press the selector
switch (10):
• DC/switch to the right:
• The equipment will be supplied with power
from the rechargeable battery.
• AC/switch to the left:
• The equipment will be supplied with power
from the power cable.
• To change over between compressed air and
low-pressure operation, press the selector
switch (12):
• Switch to the left: Compressed air operation
• Switch in the middle: OFF
• Switch to the right: Low-pressure operation
6.2 Compressor compressed air operation
(Fig. 1a, 1b, 2, 7)
• To inflate objects with compressed air, use
the compressed air hose (5).
• Connect the adapter of the compressed air
hose to the object you wish to inflate.
• Depending on what you are inflating, also use
the adapters (7, 8, 9) or other adapters availa-
ble from retail stores.
• The pressure at the compressed air hose will
be displayed in the display (11).
• The unit of the displayed pressure can be se-
lected with the button (15). The pressure can
be displayed in units of [bar], [PSI] or [kPa].
• The button (14) allows the desired pressure
to be reduced.
• The button (16) allows the desired pressure
to be increased.
• Switch on the equipment by moving the se-
lector switch (12) to the compressed air ope-
ration position (see 6.1.).
• The compressor will then pump until the pre-
set pressure on the display is reached, then it
will switch off.
• Warning! Observe the information supplied
by the tire manufacturer and the vehicle ma-
nufacturer relating to the recommended tire
pressure.
• Warning! This equipment is not calibrated!
For a calibrated measurement value, check
the actual tire pressure using a calibrated me-
ter after you have inflated the tires yourself,
e.g. at a petrol station.
• Just before it is switched off, the pressure
which is shown in the display can be 0.05 –
0.2 bar higher than the preselected pressure,
because of overpressure in the air hose.
• Allow the compressor to cool down for about
5 minutes after every 5 minutes of operation
in order to prevent overheating.
6.3 Low-pressure blower operation
(Fig. 1a, 3, 4)
6.3.1 Suctioning air (Fig. 3, 7)
• To suction out objects with a large volume
until they are empty (e.g. deflating an air
mattress, etc.), connect the air hose (3) to the
extractor connection (13).
• Connect the air hose to the object you wish
to deflate.
• Switch on the equipment by moving the se-
lector switch (12) to the low-pressure operati-
on position (see 6.1.).
• Switch off the equipment once the object has
been sufficiently deflated.
6.3.2 Inating (Fig. 4, 7)
Warning! When using the equipment to inate
objects, check the information and safety instruc-
tions provided by the manufacturer.
• To inflate objects with a large volume (e.g.
inflating an air mattress, etc.), connect the air
hose (3) to the inflating connection (4).
• Connect the air hose to the object you wish
to inflate.
• Switch on the equipment by moving the se-
lector switch (12) to the low-pressure operati-
on position (see 6.1.).
• Switch off the equipment once the object has
been sufficiently inflated.
Anl_PRESSITO_SPK13.indb 18 16.09.2021 09:15:44

GB
- 19 -
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always take the battery out of the equipment
and pull out the power plug before starting any
cleaning work.
8.1 Cleaning
• Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
• We recommend that you clean the device
immediately each time you have finished
using it.
• Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device.The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.3 Ordering spare parts and accessories
Please provide the following information when
ordering spare parts:
• Type of unit
• Article number of the unit
• ID number of the unit
• Spare part number of the required spare part
For our latest prices and information please go to
www.Einhell-Service.com
Tip! For good results we
recommend high-quality
accessories from !
www.kwb.eu
[e-mail]
9. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled.The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offices.
10. Storage
Store the equipment and accessories in a dark
and dry place at above freezing temperature. The
ideal storage temperature is between 5 and 30
°C. Store the electric tool in its original packaging.
Anl_PRESSITO_SPK13.indb 19 16.09.2021 09:15:44

GB
- 20 -
11. Charger indicator
Indicator status Explanations and actions
Red LED Green LED
OffFlashing Ready for use
The charger is connected to the mains and is ready for use; there is no
battery pack in the charger
On OffCharging
The charger is charging the battery pack in quick charge mode.The
charging times are shown directly on the charger.
Important! The actual charging times may vary slightly from the stated
charging times depending on the existing battery charge.
OffOn The battery is charged and ready for use.
The unit then changes over to gentle charging mode until the battery is
fully charged.
To do this, leave the rechargeable battery on the charger for approx. 15
minutes longer.
Action:
Take the battery pack out of the charger. Disconnect the charger from the
mains supply.
Flashing OffAdapted charging
The charger is in gentle charging mode.
For safety reasons the charging is performed less quickly and takes more
time.The reasons can be:
- The rechargeable battery has not been used for a very long time.
- The battery temperature is outside the ideal range.
Action:
Wait for the charging to be completed; you can still continue to charge the
battery pack.
Flashing Flashing Fault
Charging is no longer possible.The battery pack is defective.
Action:
Never charge a defective battery pack.
Take the battery pack out of the charger.
On On Temperature fault
The battery pack is too hot (e.g. due to direct sunshine) or too cold
(below 0° C).
Action:
Remove the battery pack and keep it at room temperature (approx. 20° C)
for one day .
Anl_PRESSITO_SPK13.indb 20 16.09.2021 09:15:44

GB
- 21 -
For EU countries only
Never place any electric power tools in your household refuse.
To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and
its implementation in national laws, old electric power tools have to be separated from other waste and
disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment
must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment.
The old equipment can be returned to a suitable collection point that will dispose of the equipment in
accordance with the national recycling and waste disposal regulations. This does not apply to any ac-
cessories or aids without electrical components supplied with the old equipment.
The reprinting or reproduction by any other means, in whole or in part, of documentation and papers ac-
companying products is permitted only with the express consent of the Einhell Germany AG.
Subject to technical changes
Anl_PRESSITO_SPK13.indb 21 16.09.2021 09:15:45

GB
- 22 -
Service information
We have competent service partners in all countries named on the guarantee certicate whose contact
details can also be found on the guarantee certicate. These partners will help you with all service re-
quests such as repairs, spare and wearing part orders or the purchase of consumables.
Please note that the following parts of this product are subject to normal or natural wear and that the
following parts are therefore also required for use as consumables.
Category Example
Wear parts* Battery
Consumables*
Missing parts
* Not necessarily included in the scope of delivery!
In the effect of defects or faults, please register the problem on the internet at www.Einhell-Service.com.
Please ensure that you provide a precise description of the problem and answer the following questions
in all cases:
• Did the equipment work at all or was it defective from the beginning?
• Did you notice anything (symptom or defect) prior to the failure?
• What malfunction does the equipment have in your opinion (main symptom)?
Describe this malfunction.
Anl_PRESSITO_SPK13.indb 22 16.09.2021 09:15:45

GB
- 23 -
Warranty certicate
Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the
unlikely event that your device develops a fault, please contact our service department at the address
shown on this guarantee card.You can also contact us by telephone using the service number shown.
Please note the following terms under which guarantee claims can be made:
1. These guarantee terms apply to consumers only, i.e. natural persons intending to use this product
neither for their commercial activities nor for any other self-employed activities. These warranty
terms regulate additional warranty services, which the manufacturer mentioned below promises to
buyers of its new products in addition to their statutory rights of guarantee.Your statutory guarantee
claims are not affected by this guarantee. Our guarantee is free of charge to you.
2. The warranty services cover only defects due to material or manufacturing faults on a product which
you have bought from the manufacturer mentioned below and are limited to either the rectication of
said defects on the product or the replacement of the product, whichever we prefer.
Please note that our devices are not designed for use in commercial, trade or professional applica-
tions. A guarantee contract will not be created if the device has been used by commercial, trade or
industrial business or has been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly instructions or due to incorrect
installation, a failure to follow the operating instructions (for example connecting it to an incorrect
mains voltage or current type) or a failure to follow the maintenance and safety instructions or by ex-
posing the device to abnormal environmental conditions or by lack of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example overloading the device or the
use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand,
stones or dust, transport damage), the use of force or damage caused by external forces (for ex-
ample by dropping it).
- Damage to the device or parts of the device caused by normal or natural wear or tear or by normal
use of the device.
4. The guarantee is valid for a period of 24 months starting from the purchase date of the device. Gu-
arantee claims should be submitted before the end of the guarantee period within two weeks of the
defect being noticed. No guarantee claims will be accepted after the end of the guarantee period.
The original guarantee period remains applicable to the device even if repairs are carried out or
parts are replaced. In such cases, the work performed or parts tted will not result in an extension
of the guarantee period, and no new guarantee will become active for the work performed or parts
tted. This also applies if an on-site service is used.
5. To make a claim under the guarantee, please register the defective device at:
www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new
device. Devices that are returned without proof of purchase or without a rating plate shall not be
covered by the guarantee, because appropriate identication will not be possible. If the defect is co-
vered by our guarantee, then the item in question will either be repaired immediately and returned to
you or we will send you a new replacement.
Of course, we are also happy offer a chargeable repair service for any defects which are not covered by
the scope of this guarantee or for units which are no longer covered. To take advantage of this service,
please send the device to our service address.
Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as
set out in the service information in these operating instructions.
Anl_PRESSITO_SPK13.indb 23 16.09.2021 09:15:45