EINHELL TE-AC 36/6/8 Li OF Set-Solo User manual

TE-AC 36/6/8 Li OF Set
Art.-Nr.: 4020455 I.-Nr.: 21021
7
EN Operating instructions
Cordless Air Compressor
FR Mode d’emploi
Compresseur d’air compact sans
fil
SP Manual de instrucciones
Compresor de aire compacto e
inalámbrico
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 1Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 1 21.04.2022 12:54:3221.04.2022 12:54:32

- 2 -
1a
7
4
15
4
9
2
1b
5
8 6
1
10
11
3
18
12
13
12
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 2Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 2 21.04.2022 12:54:3321.04.2022 12:54:33

- 3 -
2
3 4
5
24
15
17
14
16
19
20
6a
21
21
6b
30
25
26
27
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 3Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 3 21.04.2022 12:54:3721.04.2022 12:54:37

- 4 -
7 8
9 10
11
22 23
21
22
23
27 27
28 29
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 4Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 4 21.04.2022 12:54:3821.04.2022 12:54:38

EN
- 5 -
Danger! - Read the operating instructions to reduce the risk of injury.
Caution! Wear ear-muffs. The impact of noise can cause damage to hearing.
Store the batteries only in dry rooms with an ambient temperature of 50°F to 104°F (+10°C to +40°C).
Place only fully charged batteries in storage (charged at least 40%).
104°F
(+40°C)
50°F
(+10°C)
Beware of hot parts!
Beware of electrical voltage!
Warning! The equipment may start-up without warning.
PS: Max. operating pressure
Tmax: Max. operating temperature
Tmin: Min. operating temperature
V: Tank capacity
PS: 135 PSI/lb/po2(9.3 bar)
Tmin:14°F (-10°C)
Tmax:212°F (+100°C)
V: 1.6 Gallon (6 L)
Information for pressure tank:
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 5Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 5 21.04.2022 12:54:3921.04.2022 12:54:39

EN
- 6 -
DANGER!
When using the equipment, a number of safety
precautions must be observed to avoid injuries
and damage. Please read the complete operating
instructions and safety information with due care.
Keep these operating instructions in a safe place
so that the information is available at all times. If
you give the equipment to any other person, hand
over these operating instructions and the safety
information as well. We cannot accept any liability
for damage or accidents which arise due to
failure to follow these instructions and the safety
information.
1. Safety information
DANGER!
Read all the safety information and
instructions. Failure to adhere to the safety
information and instructions set out below
may result in electric shock, fire and/or serious
injury. Keep all the safety information and
instructions in a safe place for future use.
General safety information for power tools
The term “power tool“ used in the safety
regulations refers to power tools operated from
the mains power supply (with a power cable) and
to battery operated power tools (without a power
cable).
1) Work area safety
a) Keep work area clean and well lit.
Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp
location is unavoidable, use a ground
fault circuit interruptor (GFCI) protected
supply. Use of an GFCI reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the Off-position before
connecting to power source and/or
BATTERY pack, picking up or carrying the
tool. Carrying power tools with your finger on
the switch or energizing power tools that have
the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A wrench
or a key left attached to a rotating part of the
power tool may result in personal injury.
e) Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewelery or long hair
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 6Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 6 21.04.2022 12:54:4021.04.2022 12:54:40

EN
- 7 -
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of these devices can reduce dust
related hazards.
h) Do not let familiarity gained from frequent
use of tools allow you to become
complacent and ignore tool safety
principles. A careless action can cause
severe injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or remove the battery pack,
if detachable, from the power tool before
making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools and accessories.
Check for misalignment or binding of
moving parts, breakage of parts and
any other condition that may affect the
power tool’s operation. If damaged, have
the power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with
these instructions and in the manner
intended for the particular type of power
tool, taking into account the working
conditions and the work to be performed.
Use of the power tool for operations different
from intended could result in a hazardous
situation.
h) Keep handles and grasping surfaces
dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do
not allow for safe handling and control of the
tool in unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and
fire.
c) When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
e) Do not use a BATTERY pack or tool that
is damaged or modified. Damaged or
modified batteries may exhibit unpredictable
behavior resulting in fire, EXPLOSION or risk
of injury.
f) Do not expose a BATTERY pack or tool to
fire or excessive temperature. Exposure to
fire or temperature above 266°F (130°C) may
cause explosion.
g) Follow all charging instructions and do
not charge the BATTERY pack or tool
outside the temperature range specified
in the instructions. Charging improperly or
at temperatures outside the specified range
may damage the BATTERY and increase the
risk of fire.
6) Service
a) Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
b) Never service damaged BATTERY packs.
Service of BATTERY packs should only be
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 7Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 7 21.04.2022 12:54:4021.04.2022 12:54:40

EN
- 8 -
performed by the manufacturer or authorized
service providers.
Additional safety instructions
We pay a great deal of attention to the design
of every battery pack to ensure that we supply
you with batteries which feature maximum
power density, durability and safety.The battery
cells have a wide range of safety devices.
Each individual cell is initially formatted and its
electrical characteristic curves are recorded.
These data are then used exclusively to be able
to assemble the best possible battery packs.
Despite all the safety precautions, caution
must always be exercised when handling
batteries.The following points must be
obeyed at all times to ensure safe use.
Safe use can only be guaranteed if
undamaged cells are used. Incorrect
handling can cause cell damage.
Caution! Analyses confirm that incorrect use and
poor care are the main causes of the damage
caused by high performance batteries.
Information about the battery
1. The battery pack supplied with your cordless
tool is not charged.The battery pack has to
be charged before you use the tool for the first
time.
2. For optimum battery performance avoid low
discharge cycles. Charge the battery pack
frequently.
3. Store the battery pack in a cool place, ideally
at 59°F (15°C) and charged to at least 40%.
4. Lithium-Ion batteries are subject to a natural
ageing process.The battery pack must be
replaced at the latest when its capacity
falls to just 80% of its capacity when new.
Weakened cells in an aged battery pack are
no longer capable of meeting the high power
requirements and therefore pose a safety risk.
5. Do not throw battery packs into an open fire.
There is a risk of explosion!
6. Do not ignite the battery pack or expose it to
fire.
7. Do not exhaustively discharge batteries.
Exhaustive discharge will damage the battery
cells.The most common cause of deep
discharge is lengthy storage or non-use of
partly discharged batteries. Stop working as
soon as the performance of the battery falls
noticeably or the electronic protection system
triggers. Place the battery pack in storage
only after it has been fully charged.
8. Protect batteries and the tool from
overloads. Overloads will quickly result
in overheating and cell damage inside the
battery housing without this overheating
actually being apparent externally.
9. Avoid damage and shocks. Replace
batteries which have been dropped from
a height of more than one meter or which
have been exposed to violent shocks without
delay, even if the housing of the battery pack
appears to be undamaged.The battery cells
inside the battery may have suffered serious
damage. In this respect, please also read the
waste disposal information.
10. If the battery pack suffers overloading and
overheating, the integrated protective cut-
offwill switch offthe equipment for safety
reasons. Caution! Do not press the ON/OFF
switch any more if the protective cut-offhas
actuated.This may damage the battery.
11. Use only original battery packs.The use
of other batteries may result in injuries,
explosion and a fire risk.
12. Protect your rechargeable battery against
moisture, rain and high humidity. Moisture,
rain and high humidity can cause dangerous
cell damage. Never charge or work with
batteries which have been exposed to
moisture, rain or high humidity – replace them
immediately.
13. If your equipment is fitted with a detachable
battery, remove the battery for safety reasons
after you have finished your work.
Information on chargers and the charging
process
1. Please check the data marked on the rating
plate of the battery charger. Be sure to
connect the battery charger to a power supply
with the voltage marked on the rating plate.
Never connect it to a different mains voltage.
2. Protect the battery charger and its cable from
damage and sharp edges. Have damaged
cables repaired without delay by a qualified
electrician.
3. Keep the battery charger, batteries and the
cordless tool out of children‘s reach.
4. Do not use damaged battery chargers.
5. Do not use the supplied battery charger to
charge other cordless tools.
6. In heavy use the battery pack will become
warm. Allow the battery pack to cool to room
temperature before commencing with the
charging.
7. Do not over-charge batteries. Do not
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 8Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 8 21.04.2022 12:54:4021.04.2022 12:54:40

EN
- 9 -
exceed the maximum charging times.These
charging times apply only to discharged
batteries. Frequent insertion of a charged
or partly charged battery pack will result in
over-charging and cell damage. Do not leave
batteries in the charger for more than 48
hours.
8. Never use or charge batteries if you
suspect that the last time they were
charged was more than 12 months
previously. There is a high probability
that the battery pack has already suffered
dangerous damage (exhaustive discharge).
9. Charging batteries at a temperature below
50°F (10°C) will cause chemical damage to
the cell and may cause a fire.
10. Do not use batteries which have heated
during the charging process, as the battery
cells may have suffered dangerous damage.
11. Do not use batteries which have suffered
curvature or deformation during the charging
process or which show other non-typical
symptoms (gassing, hissing, cracking,…)
12. Never fully discharge the battery pack
(recommended depth of discharge max.
80%) A complete discharge of the battery
pack will lead to premature ageing of the
battery cells.
13. Never charge the batteries unsupervised.
Protection from environmental influences
1. Wear suitable work clothes.Wear safety
goggles.
2. Protect your cordless tool and the battery
charger from moisture and rain. Moisture
and rain can cause dangerous cell damage.
3. Do not use the cordless tool or the battery
charger near vapors and inflammable liquids.
4. Use the battery charger and cordless tools
only in dry conditions and an ambient
temperature of 50°F to 104°F (10°C to 40°C).
5. Do not keep the battery charger in places
where the temperature is liable to reach over
104°F (40°C). In particular, do not leave the
battery charger in a car that is parked in the
sunshine.
6. Protect batteries from overheating.
Overloads, over-charging and exposure to
direct sunlight will result in overheating and
cell damage. Never charge or work with
batteries which have been overheated –
replace them immediately if possible.
7. Storage of batteries, battery chargers
and cordless tools. Store the charger and
your cordless tool only in dry places with an
ambient temperature of 50°F to 104°F (10°C
to 40°C). Store the Lithium-Ion rechargeable
battery in a cool and dry place at 50°F to 68°F
(10°C to 20°C). Protect them from humidity
and direct sunlight! Place only fully charged
batteries in storage (charged at least 40%).
8. Prevent the Lithium-Ion battery pack from
freezing. Battery packs which were stored
below 32°F (0°C) for more than 60 minutes
must be disposed of.
9. When handling batteries beware of
electrostatic charge: Electrostatic discharges
cause damage of the electronic protection
system and the battery cells. Avoid
electrostatic charging and never touch the
battery poles.
Battery Caution + Disposal
Disposal
Should your appliance need replacement after
extended use, do not dispose of it with the
household refuse, but in an environmentally safe
way.
Waste produced by electrical machine
items should not be handled like normal
household rubbish. Please recycle where
recycle facilities exist.Check with your local
authority or retailer for recycling advice.
Always dispose of your battery pack according
to federal, state, provincial and local regulations.
Contact a recycling agency in your area for recycling
locations.
CAUTION! Even discharged battery packs
contain some energy. Before disposing, use
electrical tape to cover the terminals to prevent
the battery pack from shorting, which could cause
a fire or explosion.
WARNING! To reduce the risk of injury or
explosion, never burn or incinerate a battery
pack even if it is damaged, dead, or completely
discharged.When burned, toxic fumes and
materials are emitted into the surrounding
atmosphere.
1. Batteries vary according to device. Consult
your manual for specific information.
2. Install only new batteries of the same type in
your product (where applicable).
3. Failure to insert batteries in the correct
polarity, as indicated in the battery
compartment or manual, may shorten the life
of the batteries or cause batteries to leak.
4. Do not mix old and new batteries.
5. Do not mix Alkaline, Standard (Carbon-Zinc),
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 9Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 9 21.04.2022 12:54:4021.04.2022 12:54:40

EN
- 10 -
or Rechargeable (Nickel Cadmium, Nickel
Metal Hydride, or Lithium-Ion) batteries.
6. Do not dispose of batteries in fire.
7. Batteries should be recycled or disposed of
as per state, provincial and local guidelines.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fires.
Safety information for the inflator/deflator
Danger! The following basic safety actions
must be taken when using this inflator/
deflator in order to protect the user from
electric shocks and the risk of injury and fire.
Read and follow these instructions before
using the equipment.
• Check the ambient conditions
Do not expose the inflator/deflator to rain.
Never use the inflator/deflator in damp or wet
locations.There is a risk of electric shock!
Provide good lighting. Do not use the inflator/
deflator near flammable liquids or gases.
There is a risk of explosion!
• Protect yourself against electric shocks
Avoid bodily contact with earthed parts, e.g.
pipes, radiators, cookers and refrigerators.
• Keep children away
Do not allow other persons to touch the
inflator/deflator or cable, keep them away
from your work area.
• Do not use the cable for purposes other
than that for which it is designed
Do not carry the inflator/deflator by its cable
and do not use the cable to pull the plug out
of the socket. Protect the cable from heat,
oil and sharp edges.The cable/plug could
become damaged.
• Take care of your inflator/deflator
Keep your inflator/deflator clean in order to
work well and safely. Follow the maintenance
instructions. Check the power plug and cable
on a regular basis and have them replaced by
an authorized specialist if they are damaged.
Check the extension cable regularly and
replace it if damaged.
• Avoid unintentional starting
Make sure that the switch is turned off when
connecting to the power supply.
• Check your inflator/deflator for damage
Before using the inflator/deflator again,
carefully check the safety devices and any
slightly damaged parts to ensure that they
are in good working order. Check that the
moving parts are working correctly, that they
do not jam, and that no parts are damaged.
Make sure that all parts are fitted correctly to
ensure that the equipment remains safe to
use. Unless otherwise stated in the operating
instructions, damaged guards and parts have
to be repaired or replaced by a customer
service workshop. Damaged switches have to
be replaced by a customer service workshop.
Never use an electric power tool with a switch
that cannot be turned on and off.
• Leave all repairs to a qualified electrician
Repairs must be left strictly to qualified
electricians or the user might suffer an
accident.
• Noise
Wear ear muffs when you use the inflator/
deflator.
• Replacing the power cable
To prevent hazards, leave the replacement
of damaged power cables strictly to the
manufacturer or a qualified electrician.There
is a risk of electric shock!
• Inflating tires
Directly after inflating tires, check the
pressure with a suitable pressure gauge, for
example at your filling station.
• Place of installation
Set up the inflator/deflator on an even
surface.
• WARNING! Risk of injury - Do not direct air
stream at body.
Safety instructions for working with
compressed air and blow-out pistols
• The air which is sucked in by the deflator
must be kept free of impurities that could
cause fires or explosions in the deflator pump.
• Wear safety goggles. Foreign bodies or blown
off parts can easily cause injuries.
• Do not blow at people and do not clean
clothes while being worn. Risk of injury!
Safety information for paint spraying
• Do not process any paints or solvents with a
flash point below 131°F (55°C).There is a risk
of explosion!
• Do not heat up paints or solvents. There is a
risk of explosion!
• If hazardous liquids are processed, wear
protective filter units (face guards). Also,
adhere to the safety information provided by
the manufacturers of such liquids.
• The details and designations of the
Ordinance on Hazardous Substances, which
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 10Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 10 21.04.2022 12:54:4021.04.2022 12:54:40

EN
- 11 -
are displayed on the outer packaging of
the processed material, must be observed.
Additional protective measures are to be
undertaken if necessary, particularly the
wearing of suitable clothing and masks.
• Do not smoke during the spraying process
and/or in the work area.There is a risk
of explosion! Paint vapors are easily
combustible.
• Never set up or operate the equipment in the
vicinity of a fire place, open lights or sparking
machines.
• Do not store or eat food and drink in the work
area. Paint vapors are harmful to your health.
• The work area must exceed 1060 cu ft
(30 m3) and sufficient ventilation must be
ensured during spraying and drying. Do not
spray against the wind. Always adhere to the
regulations of the local police authority when
spraying combustible or hazardous materials.
• Do not process media such as white spirit,
butyl alcohol and methylene chloride with the
PVC pressure hose.These media will destroy
the pressure hose.
Operating pressure vessels
• You must keep your pressure vessel in good
working order, operate the vessel correctly,
monitor the vessel, carry out necessary
maintenance and repair work immediately
and meet the relevant safety precautions.
• The supervisory authority may enforce
essential control measures in individual
cases.
• A pressure vessel is not allowed to be used if
it has faults or deficiencies that can endanger
workers or third parties.
• Check the pressure vessel for signs of rust
and damage each time before using. Do not
use the compressor with a damaged or rusty
pressure vessel. If you discover any damage,
then please contact the customer service
workshop.
SAVE THESE INSTRUCTIONS
2. Layout and items supplied
2.1 Layout
1. Housing cover
2. Pressure tank
3. Intake air filter
4. Foot
5. Quick-lock coupling (regulated compressed
air)
6. Pressure gauge (for reading the set pressure)
7. Pressure regulator
8. ON/OFF switch
9. Transport handle
10. Safety valve
11. Drainage cock for condensation water
12. Lithium-Ion battery pack (not supplied)
13. Storage compartment for 8-piece adapter set
14. 8-piece adapter set
15. Air Blow gun with Pressure gauge
16. Blow-out adapter
17. Air hose
18. Battery cover
19. Switch for battery charge level indicator
20. Battery charge level indicator
21. Adapter I
22. Adapter II
23. Vent adapter
24. Relief valve
25. Inflating needle
26. Schrader to Presta adapter for bicycle tires
27. Plastic nozzle adapter
28. Tapered Metal nozzle
29. Tapered Rubber nozzle
30. Air Chuck hose
2.2 Items supplied
Please check that the article is complete as
specified in the scope of delivery. If parts are
missing, please contact our service center or the
store where you made your purchase at the latest
within 5 work days after purchasing the article and
upon presentation of a valid bill of purchase.
• Open the packaging and take out the
equipment with care.
• Remove the packaging material and any
packaging and/or transportation braces (if
present).
• Check to see if all the items are supplied.
• Inspect the equipment and accessories for
transport damage.
• If possible, keep the packaging until the end
of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, plastic sheets and small parts.There is
a risk of choking and suffocating!
• Air blow gun with pressure gauge
• Blow-out adapter
• 8-piece adapter set
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 11Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 11 21.04.2022 12:54:4021.04.2022 12:54:40

EN
- 12 -
• Air hose 8.2 ft (2.5 m)
• Original operating instruction with safety
information
Separately available accessories
18V 1.5Ah PXC Lithium-Ion battery
18V 2.0Ah PXC Lithium-Ion battery
18V 2.5Ah PXC Lithium-Ion battery
18V 3.0Ah PXC Lithium-Ion battery
18V 4.0Ah PXC Lithium-Ion battery
18V 3.0Ah PXC Plus Lithium-Ion battery
18V 4.0Ah PXC Plus Lithium-Ion battery
18V 5.2Ah PXC Plus Lithium-Ion battery
18V 4.0Ah/6.0Ah PXC Plus Lithium-Ion battery
18V 5.0Ah/8.0Ah PXC Plus Lithium-Ion battery
18V PXC Dual Port Fast Charger
18V PXC Fast Charger
Contact your local retailer for more specific
models of batteries and charger available in your
area.You can also explore battery + charger
options at Einhell.com.
3. Intended use
The cordless air compressor is designed to
generate compressed air for compressed air
driven tools.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse.The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.
4. Technical data
Motor power supply: ............. 36V (2x 18V)
Compressor speed: ................. 3200 RPM (min-1)
Max. Operating pressure: ..........135 PSI (9.3 bar)
Pressure vessel capacity: ............. 1.6 Gallon (6 l)
Theoretical suction rate:......4.59 CFM (130 l/min)
Output (compressed air)
at 102 PSI (7 bar): ................1.34 CFM (38 l/min)
Output (compressed air)
at 58 PSI (4 bar): ..................1.94 CFM (55 l/min)
Protection type: ............................................IPX0
Weight: ........................................22 lbs (10.5 kg)
5. Before starting the equipment
Before you connect the equipment to the power
supply make sure that the data on the rating plate
is identical to that of the rechargeable battery.
• Check the equipment for damage which may
have occurred in transit. Report any damage
immediately to the transport company which
was used to deliver the compressor.
• Install the compressor in the vicinity of the
point of consumption.
• Avoid long air lines.
• Make sure that the intake air is dry and
dustfree.
• Do not install the compressor in a damp or
wet room.
• The compressor may only be used in suitable
rooms (with good ventilation and an ambient
temperature from 41 °F to 104 °F (+5 °C to
40 °C).There must be no dust, acids, vapors,
explosive gases or inflammable gases in the
room.
• The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor
in areas where work is conducted with
sprayed water.
• Operate the equipment only on a firm, level
surface.
• Use flexible hoses in order to prevent
transmitting unacceptable loads to the
pipeline system at the connection between
the compressor system and the pipeline
system.
• It is essential to use separators, traps and
drains which process the liquids produced
by the compressor before the compressor
system is put into operation.
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 12Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 12 21.04.2022 12:54:4021.04.2022 12:54:40

EN
- 13 -
• Supply hoses at pressures above 102 PSI (7
bar) should be equipped with a safety cable
(e.g. a wire rope).
6. Assembly and starting
Important!
You must fully assemble the equipment
before using it for the first time.
6.1 On/Offswitch (Fig. 1a)
To switch on the equipment, set the On/Offswitch
(8) to position 1.
To switch offthe equipment, move the On/Off
switch (8) to position 0.
6.2 Setting the pressure (Fig. 1a)
• You can adjust the pressure on the pressure
gauge (6) using the pressure regulator (7).
• The set pressure can be drawn from the
quick-lock coupling (5).
6.3 Setting the pressure switch
The pressure switch is set at the factory.
Cut-in pressure approx. 87 PSI (6 bar)
Cut-out pressure approx. 135 PSI (9.3 bar)
6.4 Charging the Lithium-Ion battery (not
included)
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.5 Battery capacity indicator (Fig. 3 / item
20)
Press the battery capacity indicator switch (19).
The battery capacity indicator (20) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED flashing:
The battery is empty, recharge the battery.
All LEDs flashing:
The temperature of the battery is too low. Remove
the battery from the device and leave it at room
temperature for a day. If the error occurs again,
this means that the battery has been completely
depth-discharged and is defective. Remove the
battery from the device. Never use or charge a
defective battery.
7. Operation
7.1 Tire pressure gauge with adapters (Fig. 2)
Working pressure in PSI: 0-135 (0-9.3 bar)
Range of applications:
The tire pressure gauge (15) allows you to inflate
car tires easily and exactly. Use the pressure
gauge to check the tire pressure. If the tire
pressure is too high, you can reduce the pressure
with the integrated relief valve (24).The tire
pressure gauge comes with a valve adapter for
car tire valves.
Warning! Observe the information supplied
by the tire manufacturer and the vehicle
manufacturer relating to the recommended tire
pressure.
Warning! This equipment is not calibrated!
For a calibrated measurement value, check the
actual tire pressure using a calibrated meter after
you have inflated the tires yourself, e.g. at a petrol
station.
Use as a blow-out pistol
To use the tire pressure gauge as a blow-out
pistol you must first unscrew and remove the
hose with the valve adapter for care tires. Now the
blow-out adapter (16) can be screwed to the tire
pressure gauge.
Range of applications:
For cleaning and blowing out hollow spaces or
hard-to-reach areas, as well as for cleaning soiled
equipment.The infinitely variable trigger lever
allows an exact dosing of compressed air.
7.2 Instructions for the adapter set
For information on the correct use of the adapters
for the various valves, please refer to the following
overview (see Fig. 11 which shows how to
connect the adapter to the compressor).
• Inflating needle (Fig. 4/item 25)
Area of application: For inflating balls.The
ball needle can be used to inflate a variety of
different balls.
TIP: To avoid damaging the valve, moisten
the needle slightly before inserting it.
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 13Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 13 21.04.2022 12:54:4021.04.2022 12:54:40

EN
- 14 -
• Schrader to Presta adapter for bicycle
tires (Fig. 5/item 26)
Area of application: For Dunlop cycle tire
valves.
This Dunlop valve adapter is designed for
inflating cycle tires.
• Adapter I (Fig. 6a/Item 21)
Area of application: For all valves with an
internal diameter of 0.3'' (8 mm) or more.
You can use this adapter to inflate airbeds,
pools or boats.
TIP: Insert the adapter I into the valve as
shown in Figure 6b.
Important! The valve cap must be opened a
little by being pressed together slightly.
• Adapter II (Fig. 7/Item 22)
Area of application: For screw valves.
This adapter can be used for all conventional
boats, kayaks and other large items such as
pools, which are fitted with a screw valve.
• Vent adapter (Fig. 8/Item 23)
Area of application: For deflation valves you
can find a deflation valve combined with other
valves (standard valve, screw valve, etc.)
on many large articles such as an inflatable
mattress.
• Tapered metal/rubber nozzle
(Fig. 9-10/item 28-29)
Area of application:The universal adapter can
be used for inflating airbeds and other similar
items.
8. Cleaning and maintenance
Hazard!
Remove the rechargeable batteries before
doing any cleaning and maintenance work.
Warning!
Wait until the compressor has completely
cooled down. Risk of burns!
Warning!
Always depressurize the tank before carrying
out any cleaning and maintenance work.
Warning!
After use, always switch offthe equipment
immediately and pull out the rechargeable
batteries.
8.1 Cleaning
• Keep all safety devices, air vents and the
motor housing free of dirt and dust as much
as possible.Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
• We recommend cleaning the equipment
immediately each time after use.
• Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may
be aggressive to the plastic parts in the
equipment. Ensure that no water can get into
the interior of the equipment.The ingress of
water into an electric power tool increases the
risk of an electric shock.
• You must disconnect the hose and any
spraying tools from the compressor before
cleaning. Do not clean the compressor with
water, solvents or the like.
8.2 Condensed water (Fig. 1a)
Important! To ensure a long service life of the
pressure tank (2), drain offthe condensed water
by opening the drainage cock (11) each time after
using.
Check the pressure vessel for signs of rust and
damage each time before using. Do not use the
compressor with a damaged or rusty pressure
vessel. If you discover any damage, please
contact the customer service workshop.
8.3 Safety valve (10)
The safety valve has been set for the highest
permitted pressure of the pressure vessel. It is
prohibited to adjust the safety valve or remove its
seal. Actuate the safety valve from time to time
to ensure that it works when required. Pull the
ring with sufficient force until you can hear the
compressed air being released.Then release the
ring again.
8.4 Cleaning the intake air filter (3)
The intake filter prevents dust and dirt being
drawn in. It is essential to clean this filter after at
least every 300 hours in operation. A clogged
intake filter will decrease the compressor's
performance dramatically. Open the halves of
the air filter housing. Use compressed air at low
pressure (approx. 43.5 PSI (3 bar)) to blow out all
the parts of the filter and then assemble the filter
in reverse order.When cleaning, take adequate
precautions against dust (e.g. use a suitable face
mask).
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 14Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 14 21.04.2022 12:54:4021.04.2022 12:54:40

EN
- 15 -
8.5 Storage
Warning!
Pull out the rechargeable batteries and ventilate
the equipment and all connected pneumatic tools.
Switch offthe compressor and make sure that it is
secured in such a way that it cannot be started up
again by any unauthorized person.
Warning!
Store the compressor only in a dry location which
is not accessible to unauthorized persons. Always
store upright, never tilted!
8.6 Transport
• Transport the equipment only by carrying it by
the transport handle.
• Protect the equipment against unexpected
knocks and vibrations.
9. Disposal and recycling
The equipment is supplied in packaging to
prevent it from being damaged in transit.The
raw materials in this packaging can be reused or
recycled.The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse.The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offices.
The reprinting or reproduction by any other
means, in whole or in part, of documentation
and papers ac-companying the products is
strictly subject to the express consent of Einhell
Germany AG.
Subject to technical changes.
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 15Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 15 21.04.2022 12:54:4021.04.2022 12:54:40

EN
- 16 -
10. Possible causes of failure
Problem Cause Solution
The compressor
does not start.
1. No power supply.
2.The outside temperature is too low.
3.The motor is overheated.
1. Check the rechargeable batteries.
2. Do not use at an outside
temperature below 41°F (5°C).
3. Allow the motor to cool down. If
necessary, remedy the cause of the
overheating.
The compressor
starts but there is no
pressure.
1. The non-return valve has a leak.
2. Defective seals.
3.The drainage cock for condensation
water has a leak.
1. Have a service center replace the
non-return valve.
2. Check the seals and have any
defective seals replaced by a
service center.
3. Check the drainage cock and
replace if necessary.
The compressor
starts, pressure
is shown on the
pressure gauge,
but the tools do not
start.
1. Loose hose connections.
2. Leak in a quick-lock coupling.
3. Insufficient pressure set on the
pressure regulator.
1. Check the compressed air hose
and tools and replace if necessary.
2. Check the quick-lock coupling and
replace if necessary.
3. Increase the set pressure with the
pressure regulator.
If the equipment will not work in spite of the troubleshooting measures and the voltage supply being OK,
please contact customer service.
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 16Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 16 21.04.2022 12:54:4021.04.2022 12:54:40

FR
- 17 -
Danger! - Lire le mode d’emploi pour diminuer le risque de blessures.
Attention ! Portez une protection auditive. Le bruit peut provoquer une perte d’acuité auditive.
Conservez les batteries uniquement dans des locaux secs et à une température ambiante de 50-104 °F
(+10-+40 °C). Conservez les batteries uniquement en état chargé (au moins 40 % de charge).
104°F
(+40°C)
50°F
(+10°C)
Avertissement contre les parties chaudes !
Avertissement contre le risque d’électrocution !
Avertissement: L’unité peut démarrer sans avertissement.
PS : Pression de service max.
Tmax : Température de service max.
Tmin : Température de service min.
V : Capacité du réservoir
PS: 135 PSI/lb/po2(9.3 bar)
Tmin:14°F (-10°C)
Tmax:212°F (+100°C)
V: 1.6 Gallon (6 L)
Information pour réservoir sous pression:
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 17Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 17 21.04.2022 12:54:4021.04.2022 12:54:40

FR
- 18 -
Danger !
Certaines mesures de sécurité doivent être res-
pectées pendant l’utilisation des appareils pour
empêcher les blessures et les dommages. Par
conséquent, lisez attentivement le présent mode
d’emploi / les con-signes de sécurité. Conser-
vez-les bien pour avoir les informations toujours
à la portée de la main. Si vous devez passer
l’appareil à d’autres personnes, veuillez leur
remettre également le présent mode d’emploi /
les consignes de sécurité. Nous ne sommes pas
tenus des accidents ou dommages survenus à
cause de non-respect du présent mode d’emploi
et des consignes de sécurité.
1. Consignes de sécurité
Danger !
Lisez toutes les consignes de sécurité et
instructions. Le non-respect des consignes de
sécurité et des instructions peut causer une élec-
trocution, un incendie et / ou de graves blessures.
Conservez toutes les consignes de sécurité
et instructions pour l’avenir.
Consignes générales de sécurité pour les
outils électriques
Le terme « outil électrique » utilisé dans les
consignes de sécurité se réfère à des outils élec-
triques alimentés par le secteur (avec câble d’ali-
mentation) et à des outils électriques alimentés
par la batterie (sans câble d’alimentation).
1. Sécurité du lieu de travail
a) Maintenez votre espace de travail propre
et bien éclairé. Le désordre ou les espaces
de travail non éclairés peuvent provoquer des
accidents.
b) Ne travaillez pas avec l’outil électrique
dans une atmosphère explosible conte-
nant des liquides, des gaz ou des
poussières combustibles. Les appareils
électriques génèrent des étincelles pouvant
enflammer la poussière ou les vapeurs.
c) Tenez à distance les enfants et autres
personnes lors de l’utilisation de l’appa-
reil électrique. En cas de distraction, vous
pouvez perdre le contrôle de l’appareil.
2. Sécurité électrique
a) La fiche de raccordement de l’appareil
électrique doit être adaptée à la prise.
La fiche ne doit être modifiée en aucune
façon. N’utilisez pas de fiche d’adaptateur
avec les outils électriques mis à la terre.
Les fiches non modifiées et les prises adap-
tées diminuent le risque d’une électrocution.
b) Évitez le contact physique avec les sur-
faces mises à la terre, comme celles de
conduits, des chauffages, des cuisinières
et des réfrigérateurs. Il existe un risque éle-
vé d’électrocution lorsque votre corps est mis
à la terre.
c) Gardez les appareils électriques à l’abri
de la pluie ou de l’humidité. La pénétration
de l’eau dans un appareil électrique aug-
mente le risque d’une électrocution.
d) Ne détournez pas le câble de sa fonction
pour porter ou pour accrocher l’appareil
électrique ou pour retirer la fiche de la
prise. Gardez le câble à l’abri de la cha-
leur, de l’huile, des bords coupants ou
des éléments mobiles de l’appareil. Les
câbles endommagés ou enchevêtrés aug-
mentent le risque d’une électrocution.
e) Si vous travaillez avec un appareil élec-
trique dehors, utilisez uniquement une
rallonge adaptée à l’usage à l’extérieur.
L’utilisation d’une rallonge adaptée à l’usage
à l’extérieur diminue le risque d’une électro-
cution.
f) Si l’appareil électrique doit être utilisé
dans un environnement humide, utilisez
un Disjoncteur de fuite à la terre. L’utilisa-
tion d’un disjoncteur de fuite à la terre dimi-
nue le risque d’une électrocution.
3. Sécurité des personnes
a) Soyez attentif, prenez garde à ce que
vous faites et soyez raisonnable en tra-
vaillant avec un outil électrique. N’utilisez
pas un appareil électrique si vous êtes fa-
tigué ou si vous vous trouvez sous l’effet
de drogues, d’alcool ou de médicaments.
Un instant d’inattention lors de l’utilisation de
l’appareil électrique peut entraîner de graves
blessures.
b) Utilisez l’équipement de protection indivi-
duelle. Porter toujours une protection des
yeux. L’équipement de protection, tel que le
masque anti-poussière, les chaussures de
sécurité antidérapantes, le casque protecteur
ou la protection auditive utilisés dans des
conditions appropriées, permet de réduire les
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 18Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 18 21.04.2022 12:54:4021.04.2022 12:54:40

FR
- 19 -
dommages corporels.
c) Évitez tout démarrage non intentionnel.
S’assurer que le bouton marche-arrêt est
en position Arrêt (Off) avant de connecter
la source de courant et/ou la BATTERIE,
de prendre et de transporter l’outil. Trans-
porter des outils électriques avec votre doigt
sur le bouton marche-arrêt ou mettre sous
tension des outils électriques dont le bouton
marche-arrêt est position Marche (On) peut
causer des accidents.
d) Avant d’allumer l’outil électrique, retirez
les outils de réglage ou les clés. Un outil
ou une clé se trouvant dans un élément tour-
nant de la machine peut entraîner des bles-
sures.
e) Évitez une posture anormale. Ayez un
appui stable et gardez l’équilibre en per-
manence. Vous pouvez ainsi mieux contrôler
l’outil électrique dans des situations impré-
vues.
f) Portez des vêtements appropriés. Ne por-
tez pas de vêtements amples ni de bijoux.
Gardez les cheveux, les vêtements et les
gants à distance des éléments mobiles.
Des vêtements amples, bijoux ou longs che-
veux peuvent être happés par les éléments
mobiles.
g) Si des dispositifs d’aspiration ou de ré-
cupération des poussières peuvent être
montés, assurez-vous qu’ils sont connec-
tés et peuvent être utilisés correctement.
L’utilisation d’une aspiration des poussières
peut diminuer les risques causés par la pous-
sière.
h) La familiarité acquise par l’utilisation
fréquente des outils ne doit pas laisser
place à la complaisance et à l’ignorance
des principes de sécurité de l’outil. Une
action imprudente peut causer de graves
blessures en une fraction de seconde.
4. Utilisation et traitement de l’outil
électrique
a) Ne surchargez pas l’appareil. Utilisez l’outil
électrique adapté à votre application.Vous
travaillez mieux et de manière plus sûre avec
un outil électrique approprié dans la gamme
de puissance indiquée.
b) N’utilisez pas un outil électrique avec un
interrupteur défectueux. Un outil électrique
qui ne peut plus être allumé ou éteint est dan-
gereux et doit être réparé.
c) Débranchez la fiche de la source élec-
trique et / ou retirer la batterie de l’outil
électrique, si elle est amovible, avant de
procéder à des ajustements, remplacer
des accessoires ou ranger les outils
électriques. De telles mesures préventives
réduisent le risque de démarrage accidentel
de l’outil électrique.
d) Conservez les outils électriques non
utilisés hors la portée des enfants. Ne
permettez pas aux personnes qui ne sont
pas familiarisées avec cet appareil ou qui
n’ont pas lu ces instructions de l’utiliser.
Les outils électriques sont dangereux lors-
qu’ils sont utilisés par des personnes inexpé-
rimentées.
e) Entretenir les outils électriques et les
accessoires. Vérifiez la dérive d’aligne-
ment ou l’attache des pièces mobiles, la
rupture des pièces et s’assurer qu’au-
cun autre problème peut affecter le bon
fonctionnement de l’outil électrique. Faire
réparer l’outil endommagé avant l’utili-
sation. De nombreux accidents sont dus au
mauvais entretien des outils électriques.
f) Maintenez vos outils de coupe aiguisés
et propres. Les outils de coupe aux bords
tranchants bien soignés se coincent moins et
sont plus aisés à guider.
g) Utilisez l’outil électrique, les accessoires,
les outils utilisés, etc. conformément au
présent mode d’emploi. Tenez compte
des conditions de travail et de l’activité
à réaliser. L’utilisation des outils électriques
pour des usages autres que prévus peut en-
traîner des situations dangereuses.
h) Gardez les poignées et les surfaces de
prise sèches, propres et exemptes d’huile
et de graisse. Les poignées et surfaces de
prise glissantes ne permettent pas d’effectuer
une manipulation et un contrôle de l’outil en
toute sécurité dans des situations imprévues.
5. Utilisation et traitement de l’outil sans fil
a) Chargez les batteries uniquement dans
les chargeurs recommandés par le fa-
bricant. L’utilisation d’un chargeur pour des
batteries non appropriées présente un risque
d’incendie.
b) Utilisez dans les outils électriques uni-
quement les batteries prévues à cet effet.
L’utilisation d’autres batteries peut entraîner
des blessures et le risque d’incendie.
c) Conservez la batterie non utilisée à dis-
tance des trombones, pièces de monnaie,
clés, clous, vis ou autres menus objets
en métal susceptibles de provoquer un
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 19Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 19 21.04.2022 12:54:4121.04.2022 12:54:41

FR
- 20 -
pontage des contacts. Un court-circuit entre
les contacts de la batterie peut entraîner des
brûlures ou le feu.
d) En cas d’utilisation incorrecte, un li-
quide peut s’échapper de la batterie. Ne
le touchez pas. Rincez à l’eau en cas
de contact fortuit. Si le liquide entre en
contact avec les yeux, consultez égale-
ment le médecin. Le liquide s’échappant de
la batterie peut causer des irritations cuta-
nées ou des brûlures.
e) Ne pas utiliser une BATTERIE ou un outil
endommagé(e) ou modifié(e). Les batte-
ries endommagées ou modifiées peuvent agir
de manière imprévisible et donner lieu à un
incendie, une EXPLOSION ou un risque de
blessure.
f) Ne pas exposer une BATTERIE ou un outil
au feu ou à une température excessive.
Une exposition au feu ou à une température
supérieure à 266°F (130°C) peut causer une
explosion.
g) Suivre toutes les instructions de charge
et ne pas charger la BATTERIE ou l’outil
en dehors de la gamme de température
spécifiée dans les instructions. Un
mauvais chargement ou un chargement à
des températures en dehors de la gamme
spécifiée peut endommager la BATTERIE et
augmenter les risques d’incendie.
6. Service
a) Faites réparer votre outil électrique uni-
quement par des spécialistes qualifiés et
uniquement avec des pièces de rechange
d’origine. Cela garantit le maintien de la sé-
curité de l’outil électrique.
b) Ne jamais entretenir des BATTERIES
endommagées. L’entretien des BATTERIES
doit être effectué uniquement par le fabricant
ou par des prestataires de service autorisés.
Consignes spécifiques de sécurité
Nous construisons chaque batterie avec le plus
grand soin possible pour pouvoir vous trans-
mettre les batteries avec la densité énergétique,
la durabilité et la sécurité maximales. Les cellules
de batterie sont munies de dispositifs de sécurité
de plusieurs niveaux. Chaque cellule individuelle
est d’abord formatée, et leurs courbes caracté-
ristiques sont enregistrées. Ensuite, ces données
sont utilisées pour pouvoir regrouper les meil-
leures batteries possible.
Malgré toutes les mesures de sécurité, il
faut toujours être prudent en maniant les
batteries. Les points suivants doivent être
impérativement respectés pour assurer le
fonctionnement sûr.
Le fonctionnement sûr n’est possible qu’avec
des cellules intactes ! Une manipulation in-
correcte endommage les cellules.
Attention ! Des analyses confirment que l’uti-
lisation gravement inappropriée et des soins
incorrects constituent la cause principale des
dommages dus aux batteries haute performance.
Consignes concernant les batteries
1. La batterie de l’appareil sans fil n’est pas
chargée à la livraison. Par conséquent, la bat-
terie doit être chargée avant la première mise
en service.
2. Évitez des cycles de décharge à plat pour ga-
rantir la performance maximale de la batterie
! Chargez souvent votre batterie.
3. Conservez votre batterie au frais, au mieux à
59 °F (+15 °C), et chargée d’au moins à
40%.
4. Les batteries Lithium-Ion sont sujettes au
vieillissement naturel. La batterie doit être
remplacée au plus tard lorsque la capacité
de la batterie ne correspond plus qu’à 80 %
de l’état neuf. Les cellules affaiblies dans une
batterie vieilli ne tiennent plus la tête aux exi-
gences élevées en terme de performance et
présentent ainsi un risque de sécurité.
5. Ne jetez pas les batteries usées dans le feu
ouvert. Risque d’explosion !
6. Ne pas allumer la batterie et ne pas l’exposer
à la combustion.
7. Ne pas décharger complètement la bat-
terie ! La décharge complète endommage
les cellules de la batterie. La cause la plus
fréquente de la décharge complète de la bat-
terie constitue un stockage ou non-utilisation
prolongés des batteries à moitié chargées.
Terminez l’opération dès que la puissance
diminue visiblement ou la protection électro-
nique réagit. Ne conservez la batterie que
complètement chargée.
8. Protéger les batteries et l’appareil contre
la surcharge ! Une surcharge provoque ra-
pidement la surchauffe et l’endommagement
des cellules à l’intérieur du boîtier de batterie,
sans que cela puisse se voire de l’extérieur.
9. Évitez les détériorations et les chocs !
Remplacez sur-le-champ les batteries ayant
chuté d’une hauteur de plus d’un mètre ou
ayant été exposées à des coups violents,
même si le boîtier de la batterie semble intact.
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 20Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 20 21.04.2022 12:54:4121.04.2022 12:54:41