EisSound KBSound iSelect User manual

USER’S MANUAL
SPACE
CC-1194ENG-01

1
Important Safety Instructions
Before installing the unit, please read and follow the instructions provided in the Installation Manual included
in this kit.
Before operating the unit, please read and follow the instructions provided in this User´s Manual thoroughly
and save it for future reference.
WARNING - To reduce the risk of fire or electric shock:
install in accordance with the manufacturer’s instructions
do not expose this apparatus to water dripping or splashing
do not use this product near water
do not attempt to disassemble this unit
do not block any ventilation openings
do not install near any heat sources such as radiators, stoves or other equipment that produce
heat.
You are cautioned that any changes or modifications not expressly mentioned in this manual could affect the
normal operation of this equipment.
This product has been designed and tested to provide reasonable protection against harmful interference in
residential installation. However there is no guarantee that interference will not affect in a particular
installation. In these cases, reorient the receiving antenna, try to increase the separation between the
equipment and the source of interference and/or connect the equipment into an outlet on a circuit different
from that to which the source of interference is connected.
The entire risk of the installation, use, results and performance are borne by you.
When a socket plug, or a device connector is used as a mechanism to disconnect from the electrical mains,
the mechanism must be easily accessible at all times. Protect the power cord from being walked on or
pinched particularly at plugs and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use a certified technician for installation, repair and/or maintenance of this equipment and comply with all
the regulations in force in each country. Servicing maybe required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to water dripping or splashing, does not operate normally, or
has been dropped.
To change the batteries remove the cover by pressing on the tab while lifting the cover.
Use batteries type AA 1,5V. Do not discard used batteries with household waste.
1. Introduction
2. General Operating Notes
3. Operating Audio Functions
6. Selecting Turn-On Mode
4. Operating the FM Tuner
Quick Reference Guide
Table of Contents
CAUTION
DO NOT OPEN
RISK OF ELECTRIC SHOCK
!
3
5
6
7
10
14
2
15
5. Operating the wireless accessory
KB BluetoothSOUND® ®
7. Technical specifications
16
8. FAQ´S
CC-1194ENG-01

2
Delete individual FM tuning pre-sets
Delete all FM tuning pre-sets
Store all FM stations detected
Store individual FM station pre-sets
Store “IDEAL” setting
Store turn-on mode (on/off)
Quick Reference Guide
Automatic FM station scan
Directly keying
FM station frequency (e.g. 95.8 MHz)
Numeric keypad
Play/pause for the playing list
Clear
Audio level adjustment
volume/bass/treble/balance/loudness
Select +/- keys function
volume/bass/treble/balance/loudness
FM Forced Mono
On/off
Step forward and back for the playing list.
FM/DAB memory pre-sets
1”
”IDEAL” mode
Select sound source
BLUETOOTH link
Program MONO for all sound sources
Automatic FM station search sensitivity
To illustrate that an operation requires holding down a
key on the remote control for a specific amount of time,
the symbol will appear in the manual next to the
key. The screen will display the symbol.
F
F
2”
6”
2”
2”
2”
6”
6”
FM SENS 1-2-3
2”
6”
KBSOUND XX
6”
Save the kit numeric identification for
Bluetooth pairing
DAB iPOD
AUDIO IN
KBSOUND XXFM SENS 1-2-3
UPDATE DAB
CC-1194ENG-01

KB
KB
KB
SOUND
SOUND
SOUND
The
®
®
®
®
®
iSelect
iSelect
iSelect
is a sound device specially designed for quick and easy installation. It fits discreetly into the decor of your kitchen, bathroom or
anywhere in your home. Now enjoy the world of music.
Kit comprises:
Electronic module with built-in FM tuner, power supply and a Bluetooth Accessory.
Two 2 1/2” or two 5" loudspeakers.
Remote control with the following functions:
Choose the audio source, FM or Bluetooth
Volume, bass, treble and balance control.
'Forced Mono' function.
FM and RDS information.
Ability to directly key-in desired station frequency.
Ability to automatically store into memory stations received with the best reception.
30 memory pre-sets.
“Intelligent”loudness: automatic adjustment to the volume level.
When connected with the (included in this kit), it
=
=
=
4
4
4
4
4
4
4
4
wireless Accessory allows the user to listen to the music stored in any device
that has the ability to transmit via Bluetooth.
KB BluetoothSOUND® ®
The components supplied in this kit are for installation and use in the manner and for the purpose described in the Installation Manual and
the User Manual. The installation must also comply with each country's current regulations. This manual assumes that the
unit has been installed following the instructions provided in the Installation Sheet included in this kit.
3
1. Introduction
CC-1194ENG-01

CC-1194ENG-01
KB
KB
KB
SOUND
SOUND
SOUND
The
®
®
®
®
SPACE
SPACE
SPACE
is a sound device specially designed for quick and easy installation. It is our new custom made audio solution. It´s open ended
allowing you to choose your loudspeakers and amplifiers to fulfill the specific design requirements of your dream project with superb sound.
Kit comprises:
An Electronic module with built-in FM tuner, improved wiring design and connecting terminals to facilitate connecting an external
amplifier and a
Infrared receiver / transmiter
Remote control with the following functions:
Choose the audio source, FM or Bluetooth
Volume, bass, treble and balance control.
'Forced Mono' function.
FM and RDS information.
Ability to directly key-in desired station frequency.
Ability to automatically store into memory stations received with the best reception.
30 memory pre-sets.
“Intelligent”loudness: automatic adjustment to the volume level.
When connected with the (included in this kit),
=
=
=
4
4
4
4
4
4
4
4
Bluetooth
SOUND
®Accessory.
wireless Accessory allows the user to listen to the music stored in any device that
has the ability to transmit via Bluetooth.
KB Bluetooth
® ®
The components supplied in this kit are for installation and use in the manner and for the purpose described in the Installation Manual and
the User Manual. The installation must also comply with each country's current regulations. This manual assumes that the
unit has been installed following the instructions provided in the Installation Sheet included in this kit.
4

5
1.- All of the functions only work (except ON/OFF) when the Remote Control is in “on”mode.
Once the is connected to the mains, it will remain powered even it is in OFF state. The OFF
state
KBSOUND2.- ®iSelect / Space
beep
5m
The
will turn on with the
audio and station frequency
settings saved as the “ideal”
mode settings (see chapters
3 and 6) when the unit is
connected to a power
supply.
When switched off and on
while connected to the
power supply, the audio and
station frequency settings
will be the same as when
the unit was last switched off
with the Remote Control
ON/OFF key
KBSOUND®iSelect /
Space
2. General Operating Notes
DAB iPOD
AUDIO IN
3.-
4.- The Remote Control unit exchanges information (transmits and receives data) by
means of the IR capsule in the loudspeaker grille. If at any time there is a failure in the
communication, the screen will display the symbol. In the event of this
occurring, point the Remote Control to the IR capsule at a straight-line distance of no
greater than 5 meters.
5.- The Remote Control display will automatically turn off when
there has been no keying activity for more than a few seconds,
ensuring more efficient battery usage. To view the display
information at any time, point the Remote Control to the
transmission-reception capsule and press the key of the
selected sound source at this time
A short BEEP sound signal indicates that the data has been received
AUDIO IN
iPOD
CC-1194ENG-01

6
Key Sequence Display
Increase/decrease in the volume level: The LED will flash
to indicate the desired change in volume.
Increase/decrease in bass/treble levels: The LED will flash
to indicate the desired change in the bass/treble levels.
Loudness: It reinforces the bass level in terms of the volume level, assuming a
greater backing at a lower volume and a lesser backing at a higher volume.
Mono/stereo reception: When activated, this feature allows the FM stations to be received in stereo.
When deleted this feature only allows for mono reception.
Note: If the electronic module´s configuration is mono, the signal will always be received in mono
even if the signal received by the antenna is in stereo.
If the electronic module is off, a brief press on the will turn on the unit .ON/OFF key
The LED will display the word “ON”
3. Operating Audio Functions
on
vol 58
BAS+06
LD on
STEREO
IDEAL
IDEAL
2’’
"IDEAL" mode of operation: To program your "IDEAL" mode of operation, select the sound source
(FM or BT) and desired levels of volume, bass, treble and loudness. Also, if your choice is FM, select
your favorite station. Then hold down the IDEAL key for 2 seconds.
This "IDEAL" mode can be instantly accessed by simply pressing the IDEAL key on the Remote Control.
CC-1194ENG-01

7
Key Sequence Display
To directly key-in an FM station frequency, sequentially dial the numeric keys of the station
frequency then press the FM key. For example, to select 94.7, press 9 4 7 FM.
Note: A station frequency can be keyed-in as either 94.7 (9 4 7 FM)
or as 94.70 (9 4 7 0 FM)
To clear a digit and start a different
frequency, press the C key
and then begin keying-in of the desired
frequency
4.2 Direct Key-in of Station Frequency
While the search is taking place, the word “SCAN”will appear on the display screen.
The screen will duly display the station frequency of the next station found.
4.1 Station Scan
4. Operating the FM Tuner
94.70
94.70
FM
FM
SCAN
102.50
FM
1”
CC-1194ENG-01

Key Sequence Display
4.4 Storing and Clearing Station Frequencies Manually
To , tune to the station (see Chapter 4.1. Station scan and 4.2. Direct key-in of
Station Frequency).
Hold down the 9 key for 2 seconds.
The station tuned at that time will be stored in the memory.
store a station
To , select the station and hold down the 7 key for 2 seconds.
The station will be deleted from the memory.
delete a station from the memory
The UP/DOWN keys allow you to scroll through the stations stored in the memory (see
Chapter 4.4 and 4.5, Storing and Clearing Stations in Memory).
When stations are stored in the memory they are sorted in ascending order; that is, beginning
with 87.5 and ending with 108.0.
The screen will display the frequency of the station stored in that memory pre-set.
4.3 Tuning to FM Memory Pre-Sets
MEM 07
DEL MEM
MEM 19
102.50
FM
94.70
FM
94.70
FM
2’’
2’’
8
CC-1194ENG-01

Key Sequence Display
To activate the process for all the
memory slots, hold down 4 key for 6 seconds.
clearing station frequencies automatically
To activate the process, hold down key 6 for 6
seconds.
When the automatic programming begins the screen will display the word “AUTO”.
The electronic module will store into the memory the stations that are received with the best
reception, sequentially from lowest frequency (87.5 MHz) to highest frequency (108.0 MHz).
The system will use all the memory slots available, reaching a maximum of 30.
The process can take a few moments. Once the scan has been completed or once the
maximum number of memory slots has been fully used, the process ends and a BEEP signal
sounds.
storing station frequencies automatically
4.5 Storing and Clearing Station Frequencies Automatically
To adjust the automatic station scan sensitivity (see chapter 4.1. Station
scan), select a value between 1 (minimum) and 3 (maximum) and press key
FM SEN for 2 seconds
4.6 Adjusting Station Scan Sensitivity
DEL ALL
AUTO
beep
6’’
6’’
SENS 1
FM SENS 1-2-3FM SENS 1-2-3
2’’
2’’
2’’
FM SENS 1-2-3
FM SENS 1-2-3
SENS 2
SENS 3
9
CC-1194ENG-01

CC-1194ENG-01
10
Key
sequence Display
The wireless accessory allows you to listen to the
music stored in any device that has the ability to transmit via Bluetooth
through the 2 1/2", 5" or
SPACE kts.
KB Bluetooth
KB KB
KB
SOUND
SOUND iSelect SOUND iSelect
SOUND
® ®
® ®
®
5. Operating the
wireless accessory
KBSOUND®
05
6”
KBsound XX
IMPORTANT: Before pairing the Bluetooth a numeric
address must be assigned to each kit installed (See
Chapter 5.2).
Several kits in the same house can be distinguished by assigning
them a different identification number such as KBsound 00 or 01, 02
etc.
KB
KB
SOUND
SOUND
®
®
KB-05
5.1.- Assign a numeric address to your KB BluetoothSOUND® ®
iPOD BT
Select Bluetooth key.
Dial the two digits that identify the KBsound kit
such as “05" on the Remote Control.
Then press the 2 key for aproximately
5 seconds.
A confirmation beep will be heard through the
speaker to indicate that the identifier has
been stored.
KBsound00 KBsound01 KBsound02
KBsound03 KBsound04 KBsound05
beep
From this moment the identification code of that kit becomes KBsound 05.
Repeat this procedure for all kits you have installed in your home, taking care of
choosing different numbers for each one.
IMPORTANT: before you begin make
sure that the Bluetooth device from
which you want to stream the music has
the A2DP and AVRCP profiles.

CC-1194ENG-01
5.2.- Pairing a new Bluetooth device
Before being able to stream music from
a Bluetooth device to our
kits it is necessary to pair the
accessory. This operation
only needs to be carried out once with
each device.
Make sure that during the entire
operation there is only one Bluetooth
device within the range of coverage of
the .
The Remote Control must be
pointing directly at the IR receiver of the
.
Select the Bluetooth key option.
Press the 5 key on the Remote Control
for aproximately 6 seconds. “Link”will
appear in the display.
The IR led will flash in blue, and will
remain in this state until the pairing
operation is completed, or a maximum
of 3 minutes.
KB
Bluetooth
KB Bluetooth
KB Bluetooth
SOUND
SOUND
SOUND
®
®
® ®
® ®
Key
Sequence Display
Access the Bluetooth menu of your
device
In the device select the KBsoundXX
(00,01,02...) option.
Check that the code indicated on the
device matches the code displayed
on the Remote Control.
Note: To get this code the Remote
Control must be pointing directly at
the IR receiver.
The pairing process will be carried
out successfully when the IR blue led
stops flashing and “connected”
appears in the display of the
Bluetooth device.
Some Bluetooth devices may
optionally request a password to
confirm the link.
In such cases, dial 0000.
iPOD
BT
6”
DISCONNECT LINK
048233
DAB iPOD
AUDIOIN
DAB iPOD
AUDIOIN
11

CC-1194ENG-01
5.3.- Transmit audio to a KB BluetoothSOUND® ® from multiple Bluetooth devices
If you want to transmit audio from a different
Bluetooth device, press the 5 key on the
Remote Control for 6 seconds, after which the
will be freed from
any previous pairing.
Activate the Bluetooth of the new device you
wish to connect with and then select the
with which you
wish to pair (e.g. KBsound 01).
The pairing will have been carried out
successfully when the IR blue led stops
flashing.
KB Bluetooth
KB Bluetooth
SOUND
SOUND
® ®
® ®
Make sure that during the entire
operation the Remote Control is
pointing directly at the IR
receiver of the
and the Bluetooth
device is within the range of
coverage.
Select the Bluetooth key on the
Remote Control.
The kit searches for the last
Bluetooth device with which it
was paired and, if found within
its range of coverage, it will
continue to be paired
automatically.
KB
Bluetooth
SOUND®
®
Key
Sequence Display
iPOD
6”
BT
Key
Sequence Display
Several Bluetooth devices can share the same
, although only one can transmit audio at any time.
To make this possible, it is necessary to have paired all Bluetooth
devices with the .
(see chapter 5.2)
KB
Bluetooth
KB Bluetooth
SOUND
SOUND
®
®
® ®
DAB iPOD
AUDIOIN
From the Remote Control
you can select the options
PLAY /PAUSE by pressing
the button
Go forward and backward
through the music list
pressing the keys
12

CC-1194ENG-01
5.4.- Transmit audio from one device to several KB BluetoothSOUND® ®
If there are several in your installation, you will be able to transmit your music to any of them interchangeably from the same
Bluetooth mobile device. Please note that only one can receive the audio signal at any time.
To make this possible, it is necessary to have made the numeric identification of each . (see Chapter 5.1).
It is also necessary that the Bluetooth mobile device has been paired with each of the in the installation
(see chapter 5.2).
Select the Bluetooth option with the Remote Control of the
that you wish to use at that moment.
Select in the Bluetooth device the you wish to connect with:
KBsound00, KBsound01, KBsound02, etc.
NOTE: Be careful, the menus on your Bluetooth device can vary between manufacturers.
As a result, strictly follow their instructions.
KB Bluetooth
KB Bluetooth
KB Bluetooth
KB Bluetooth
KB Bluetooth
KB Bluetooth
SOUND
SOUND
SOUND
SOUND
SOUND
SOUND
® ®
® ®
® ®
® ®
® ®
® ®
Key
Sequences Display
iPOD
BT
KBsound 01
KBsound 02
KBsound 03
KBsound00 KBsound01 KBsound02
13

14
If the Turn-On mode is set to
“on”in this state, when
power is fed to the unit, it will
turn on in “ideal”mode (see
Chapter 3).
If the Turn-On mode is set to “off”,
when power is fed to the unit, it will
turn on in “off”mode.
This function is designed for use in the event that the
power supply is fed by a specifically designated switch. In this
case, the automatic activation mode must be programmed in order to
automatically turn on unit when the switch is activated.
These steps must be followed:
KB
KB
SOUND
SOUND
®
®
iSelect
or SPACE
iSelect
1. Supply power to the unit by
turning on the switch. The unit
will flicker a couple of times and turn off.
2. Turn on the unit using the
remote control (ON/OFF key).
3. With the unit turned on, keep
the ON/OFF key pressed down for 2 seconds.
KB
KB
KB
KB
SOUND / Space
SOUND
SOUND
SOUND
®
®
®
®
iSelect
iSelect / Space
iSelect / Space
iSelect / Space
Key Sequence Display
6. Selecting Turn-On Mode
AUTO x
2’’
2’’
CC-1194ENG-01

CC-1194ENG-01
15
7. Technical specifications
52593 MIN NORMAL MAX NOTES
Measurements 54,8x37x20 mm width x height x depth
Voltage 3,3V Vdc internal connector
Consumption 0,1 W
Bluetooth spec.
Wireless transceiver RF 2,4 GHz
Power RF 10 mWeirp
Antenna RF 2,5 dB SMA connector
Range 5 m
Class2 BT2.1 + EDR
A2DP 1.2
AVRCP 1.4
52391/92 , 52398/93 MIN NORMAL MAX COMMENTS
Measurements 200x53x56 mm
Voltage 185 230 265 Vac 50Hz, terminal F,N (ref.52391,52398)
90 120 140 Vac 50/60Hz, terminal F,N (ref.52392,52393)
Consumption demand 3,3 10 W terminals F,N (ref.52391/92)
4,8 10 W terminals F,N (ref.52398/93)
Output signal 1,5 W regletas L,R (ref.52391/92) over 16ohm
1,7 W regletas L,R (ref.52391/92) over 8ohm
2,5 W regletas L,R (ref.52391/92) over 4ohm
Passband 45 20.000 Hz
Aux.amplifier switch on signal 12 14 Vdc terminals 62, 4 (ref.52398/93)
220 mA
Distortion 0,1 %
Left/right channel separation 58 dB
FM Frequency range 87,6 108.0 MHz
FM antenna impedance 75 ohms RF connector
FM antenna sensitivity 1,7 3,5 uV
FM tuner distortion 0,1 0,5 %
Number of FM station pre-sets 30

CC-1194ENG-01
16
8. FAQ´S - Frequently asked questions
1. Weak FM signal or none at all
2. Can down lights or strong direct sunlight interfere with the correct functioning of the Remote Control?
3. Are the speakers and Remote Control Waterproof?
4. Can I add more or larger speakers?
5. Can I use multiple sets throughout the installation?
6. Do you have color options for the Speakers?
7. Can I upgrade the Select kit to a iSelect 2 ½” Bluetooth®?
If you are in an area where there is a weak FM signal or none at all, we recommend that you connect an external FM antenna to our KBSOUND kit.
This problem exists for ALL manufacturers of Audio/Video/TV equipment using IR Remote Controls. As a result, try to avoid direct sunlight and, if possible,
distance the KBSOUND kits from fluorescent lighting.
The speakers and Remote Control are not waterproof but they have been designed to operate in a bathroom environment. We recommend that you do
not install the speakers directly above the shower when they would be in constant contact with steam.
In theory it is possible to add more or larger speakers. However you should consider that the product is designed to perform with just two speakers and
the output is designed accordingly. Larger speakers may not receive enough power to do them justice and more speakers may drain the power designed
to run the two speakers it comes with.
The KBSOUND can be used in multiple rooms, they work independently.
Yes KBSOUND iSelect 2 ½ ”Bluetooth® is available in white and matt chrome. The iSelect 5”Bluetooth® comes in white only.
No, unfortunately you cannot. You will need to buy the iSelect Bluetooth® model.

CC-1194ENG-01
17
8. How do I link with BT device?
9. Can I connect my Bluetooth device to several iSelect kits at the same time?
.
10. Can I assign an address to each kit to identify them with the different zones in my installation?
11. What does the symbol mean?
12. Why does my iSelect Bluetooth® automatically switch on at random?
13. How do I store the radio stations in the memory?
Press the BT key and BT will appear in the screen of the Remote Control. Then press the 5 key for 6”until linking commences. (See User manual
page 11 Section 5.2).
Yes, you can. Before linking the KBSOUND iSelect Bluetooth® kit to your Bluetooth device a numeric address such as KBSound 01, KBSound 02, etc. can
be assigned to each KBSOUND kit installed (See User manual page 10 Section 5.1).
The Remote Control unit exchanges information (transmits and receives data) by means of the IR receiver capsule in the loudspeaker grille. If at any time
there is a failure in the communication, the screen will display the symbol. In the event of this occurring, point the Remote Control at the IR receiver
capsule at a distance of no greater than 5 meter and reconnect.
Sometimes this can occur if you inadvertently press the on /off key for more than 2”and thereby activate the Turn-on mode (Auto ). To turn off
press the on/off key for 2”and check that “Auto X”appears on the screen of the Remote Control (See User manual page 14).
Press the 6 key for 6”. When the automatic storing begins the screen in the Remote Control will display “Auto”. The kit is programed to memorize 30
presets.
No, you can only connect with one kit any one point in time
√
iPOD

64460107
Electrónica Integral de Sonido S.A. is not responsible for any error or omissions that may appear in this manual,
and reserves the right to make changes without prior notice.
AENOR
Registrada
Empresa
ER-0634/1998
[email protected]
Tel: [phone]
Fax: [phone]
www.eissound.com
CENTRAL
Polígono Malpica Calle F Oeste
Grupo Gregorio Quejido, 87-88
50016 Zaragoza (SPAIN)
US OFFICE
[email protected]
KBSOUND Inc.
245 Riverside Avenue, Suite 150
Jacksonville, Florida 32202
Tel.: [phone]
www.kbsound.com
FCC ID:
2AB6X52593
CC-1194ENG-01