Eizo FLEXSCAN T561 - User manual

User’s Manual
T561
FlexScan
Color Display Monitor

2
SAFETY SYMBOLS
This manual uses the safety symbols below. They denote critical information. Please
read them carefully.
WARNING
Failure to abide by the information in a WARNING may result in serious
injury and can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate
injury and/or property or product damage.
Indicates a prohibited action.
Indicates to ground for safety.
Copyright© 2000 by EIZO NANAO CORPORATION. All rights reserved. No part of
this manual may be reproduced, stored in a retrieval system, or transmitted, in any form
or by any means, electronic, mechanical, or otherwise, without the prior written
permission of Eizo Nanao Corporation.
Eizo Nanao Corporation is under no obligation to hold any submitted material or
information confidential unless prior arrangements are made pursuant to Eizo Nanao
Corporation's receipt of said information. Although every effort has been made to ensure
that this manual provides up-to-date information, please note that EIZO monitor
specifications are subject to change without notice.
ENERGY STAR is a U.S. registered mark.
Apple and Macintosh are registered trademarks of Apple Computer, Inc.
VGA is a registered trademark of International Business Machines Corporation.
DPMS is a trademark and VESA is a registered trademark of Video Electronics
Standards Association.
Windows is a registered trademark of Microsoft Corporation.
ScreenManager, PowerManager, QuickSet and i·Sound are trademarks of
Eizo Nanao Corporation.
FlexScan, SuperErgoCoat and EIZO are registered trademarks of Eizo Nanao
Corporation.
As an ENERGY STAR® Partner, Eizo Nanao Corporation has determined that
this product meets the ENERGY STAR guidelines for energy efficiency.

CONTENTS 3
ENGLISH
CONTENTS
PRECAUTIONS ............................................................................. 4
1. INTRODUCTION ............................................................................ 9
1-1. Features ....................................................................................................... 9
1-2. Package Contents ........................................................................................ 9
1-3. Controls & Connectors ................................................................................ 10
2. INSTALLATION ........................................................................... 11
2-1. Connecting the monitor to the PC ............................................................... 11
2-2. Getting Ready for Operation ....................................................................... 13
3. SCREEN ADJUSTMENT ............................................................ 14
3-1. How to use the ScreenManager .................................................................. 14
3-2. Adjustments and Settings ........................................................................... 15
3-3. Special Function ......................................................................................... 20
4. CONNECTING TWO PCs TO THE MONITOR .............................. 21
5. TROUBLESHOOTING ................................................................. 22
6. CLEANING ................................................................................... 26
7. SPECIFICATIONS ....................................................................... 27
8. GLOSSARY.................................................................................. 29
9. INDEX .......................................................................................... 31

4PRECAUTIONS
IMPORTANT!
•This product has been adjusted specifically for use in the region to which it was
originally shipped. The performance of the product, (i.e. picture geometry, picture
positioning and color convergence and purity in the case of color monitors) is
optimally adjusted to the earth’s magnetic field of the specific destination. If operated
outside the region to which it was originally shipped, the product may not perform as
stated in the specifications.
•To ensure personal safety and proper maintenance. Please read this section and the
caution statements on the monitor (refer to the figure below).
[Location of the Caution Statements]
The equipment must be connected to a grounded main outlet.
Jordet stikkontakt skal benyttes når apparatet tilkobles datanett.
Apparaten skall anslutas till jordat nätuttag.
PRECAUTIONS
WARNING
•If the monitor begins to emit smoke, smells like something is
burning, or makes strange noises, disconnect all power connections
immediately and contact your dealer for advice.
Attempting to use a malfunctioning monitor can be dangerous.
•Do not dismantle the cabinet or modify the monitor.
Dismantling the cabinet or modifying the monitor may result in electric
shock or burn.
•Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing
covers may expose you to dangerous voltage or other hazards.

ENGLISH
PRECAUTIONS 5
WARNING
•Keep small objects away from the monitor.
Small objects may accidentally fall through the ventilation slots into the
cabinet, leading to fire, shock, or equipment damage.
•Keep liquids away from the monitor.
Spillage into the cabinet may result in fire, electric shock, or equipment
damage. If an object or liquid falls/spills into the cabinet, unplug the
monitor immediately. Have the unit checked by a qualified service
engineer before using it again.
•Place the monitor on a strong, stable surface.
A unit placed on an inadequate surface may fall, resulting in injury or
equipment damage. If the monitor falls, disconnect the power immediately
and have the unit checked by a qualified service engineer before using it
again. Using a monitor after it has been dropped may result in fire or
electric shock.
•Set the monitor in an appropriate location.
* Do not install in a dusty or humid environment.
* Do not place in a location where the steam comes directly on the screen.
* Do not place near heat generating devices or a humidifier.
•Keep the plastic packing bags away from children and infants.
Plastic bags can be dangerous. To avoid danger of suffocation, keep the
bag away from babies and children.
•Keep power terminal covers for the optional i·Sound™sound unit
away from children and infants.
Children and infants may accidentally swallow the covers and choke. If
swallowed, consult a doctor immediately.
OK

6PRECAUTIONS
WARNING
•Use the enclosed power cord. If using the power cord other than the
enclosed one, use the following cord.
[USA and Canada]
Use a UL LISTED/CSA LABELED or CERTIFIED power cord set meeting
the following specifications.
* Rating: min. 125 V, 10 A
* Length: max. 2.0 m
* Plug type: NEMA 5-15P, Parallel blade, Grounding type, 125 V, 10 A
* Type: SVT
[Europe]
Use a proper European standard approved power cord meeting the
following specifications.
* Rating: min. 250 V, 10 A
* Length: max. 2.0 m
* Type: H05VV-F 3G 1 mm2
Use a plug type approved by the country where you reside. Failure to do so
may cause fire or electric shock.
•To disconnect the power cord, grasp the plug firmly and pull.
Never tug on the cord, doing so may cause damage and could result in fire
or electric shock
•The equipment must be connected to a grounded main outlet.
•Use the correct voltage.
* The monitor is designed for use with a specific voltage only. Connection
to a different voltage may cause fire, electric shock, or other damage.
* Do not overload your power circuit, as this may result in fire or electric
shock.
* For proper connections of the power cord, be certain to plug the power
cord to the provided monitor connector and directly to a wall outlet. By
not doing so may result in fire or electric shock.
•Handle the power cord with care.
* Do not place the cord underneath the monitor or other heavy objects.
* Do not pull on the cord.
* Do not attempt to repair a damaged cord.
If the power cord becomes damaged, stop using it. Use of a damaged cord
may result in fire or electric shock.
•Never touch the plug and power cord if it begins to thunder.
If it begins to thunder, do not touch the plug, power cord and cable.
Touching them may result in electric shock.
OK

ENGLISH
PRECAUTIONS 7
CAUTION
•Handle with care when carrying the monitor.
* Disconnect the power cord, signal cables and remove the optional
i·Sound™sound unit (if applicable). Moving the monitor with the cord
attached or lifting it by the i·Sound™sound unit is dangerous. It may
result in injury or equipment damage.
* Note that the monitor is heavier at the front than at the rear. Do not
move it alone. Always work with another person.
* The screen is optically coated to reduce glare. Keep hard objects (such
as buttons, tiepins, and other clothing accessories) away from the screen
surface to prevent scratches.
•Do not block the ventilation slots on the cabinet.
* Do not place books or any other papers on the ventilation slots.
* Do not install the monitor in a closed space.
* Do not use the monitor laying down or upside down.
* Do not remove the tilt-swivel stand.
Using the monitor in this way block the ventilation slots and prevents
proper airflow, leading to fire or other damage.
•Do not sit on the cabinet or place any heavy objects on the cabinet.
A unit with heavy objects on it may fall or be damaged and result in injury.
•When adjusting the viewing angle of the monitor, do not do so by
handling i·Sound™sound unit (if applicable).
Adjusting the monitor in this way may break the unit or cause bodily
injury.
•At the end of the day or if you plan to leave the monitor unused for an
extended period, after turning off the power switch disconnect the
power cord from the wall socket so that no power connections are
made.
OK

8PRECAUTIONS
CAUTION
•Do not touch the plug with wet hands.
Touching the plug with wet hands is dangerous and can cause electrical
shock.
•Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a
problem.
•Unplug the monitor before cleaning it.
Cleaning the monitor while it is plugged into a power outlet may result in
electric shock.
•Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl
alcohol), abrasive cleaners, or other strong solvents, as these may
cause damage to the cabinet or CRT.
•Periodically clean the area around the plug.
Buildup of dust, water, or oil on the plug may result in fire.

1. INTRODUCTION 9
ENGLISH
1. INTRODUCTION
Thank you very much for choosing EIZO FlexScan T561.
1-1. Features
•High contrast natural flat type CRT.
•Dual inputs with individual color configuration.
1-2. Package Contents
Please contact your local dealer for assistance if any of the listed items are missing or
damaged.
•Monitor •Signal Cable
(MD-C87/MD-C100)
•Power Cord •User’s Manual
•EIZO CRT Utility Disk •Warranty Registration Card
•Please retain the packing materials for future transference.

10 1. INTRODUCTION
1-3. Controls & Connectors
Front
(1) ScreenManager™
(2) BNC/D-SUB Selection Button
(3) AUTO-SIZING Button
(4) Power Terminal Covers for the Optional
i·Sound Sound Unit. (Bottom side)
(5) QuickSet™Control Pad
(Hereinafter “Control Pad”)
(6) Power Indicator
Indicated color Power-on status
Green Power is on (Normal mode)
Flashing Green Power save mode 1
Advance notice of monitor’s
off timer (See page 18)
Yellow Power save mode 2
FlashingYellow Power save mode with
monitor’s off timer
(See page 18)
Rear
(7) Power Switch
(8) Power Connector
(9) D-Sub Mini 15 Pin Input Connector
(10)BNC Input Connector
(11)Maintenance Port
(11)(8)(9) (10)
(6)
(2)
(3) (5)
(7)
(1)
(4)

2. INSTALLATION 11
ENGLISH
2. INSTALLATION
2-1. Connecting the monitor to the PC
•Be sure that the power switches of both of the PC and the monitor are OFF.
1. Plug the signal cable into the connector at the rear of the monitor and
the other end of the cable into the video connector on the PC.
After connecting, secure the connection with the screw-in fasteners.
•Standard graphics board
•Macintosh
Signal Cable (Enclosed)
Signal Cable (Enclosed)
Macintosh Adapter (Optional)
Please consult EIZO dealer.
Standard graphics board
Video Output Connector
D-Sub mini 15 pin
Macintosh (Blue & White)
Video Output Connector
D-Sub mini 15 pin
Macintosh
Video Output Connector
D-Sub 15 pin

12 2. INSTALLATION
2. Plug the power cord into the power connector at the rear of the
monitor. Then plug the other end of the cord into a power outlet.
WARNING
•The equipment must be connected to a grounded main
outlet.
•Use the enclosed power cord. If using the power cord
other than the enclosed one, use the following cord.
[USA and Canada]
Use a UL LISTED/CSA LABELED or CERTIFIED power cord
set meeting the following specifications:
* Rating: min. 125 V, 10 A
* Length: max.2.0 m
* Type: SVT
* Plug type: NEMA 5-15P, Parallel blade,
Grounding type, 125 V, 10 A
[Europe]
Use a proper European standard approved power cord
meeting the following specifications:
* Rating: min. 250 V, 10 A
* Length: max. 2.0 m
* Type: H05VV-F 3G 1 mm2
Use a plug type approved by the country where you reside.
Failure to do so may cause fire or electric shock.
3. Turn on the monitor first, then the PC.
The monitor’s power indicator will light up (green). The monitor will warm up
briefly, then display an image. Whenever finishing your operation, turn off the PC
and the monitor.
(If an image does not appear, make sure that all connections have been made
properly. Refer to the “TROUBLE SHOOTING”(See page 22) for additional
advice.)
•Generally, for maximum viewing comfort, position the
monitor slightly below eye level. Staring at the monitor for
prolonged periods can cause eye strain. Be sure to take
adequate rests.
(A 10-minute rest period each hour is suggested.)

2. INSTALLATION 13
ENGLISH
2-2. Getting Ready for Operation
Try each setting procedure if necessary in the following cases.
The display image size and / or position is incorrect
Press the AUTO-SIZING button on the front panel. The AUTO-SIZING function centers
the displayed image, aligning the image’s borders with respect to the monitor frame. In
general, press the AUTO-SIZING button whenever changing the graphics board or the
resolution p.30), or when image size and/or position is incorrect. If further adjustment is
required, adjust the picture size/position as desired using the ScreenManager (See page
14).
•A solid-color screen (i.e. red, green, blue) may appear briefly after pressing the
AUTO-SIZING button. This is not a malfunction.
The displaying area is too large or too small
The following look-up table shows the maximum (non-interlaced) vertical refresh rates
for this model with regard to standard resolutions set forth by VESA. The best way to see
if the monitor will work with a given resolution and rate, is to compare the vertical
refresh rate of the graphics board to the monitor’s range. Refer to the graphics board
manual for specifications. If the refresh rate is within the specified range of the monitor,
it should operate properly.
Using the monitor with Windows®95/98/2000
A monitor information file is contained in the EIZO CRT Utility Disk included with the
monitor. It includes all the required information for best operation with Windows 95/98/
2000. Please install the enclosed utility and select your model name from the monitor
list in Windows 95/98/2000. For installation procedure, please read the readme.txt file
in the utility disk.
Horizontal Scan
Frequency (kHz)
MaximumVertical Refresh rate (Hz)
30-96 160 144 118 89 76
640 x 480 800 x 600 1024 x 768 1280 x 1024 1600 x 1200

14 3. SCREEN ADJUSTMENT
3. SCREEN ADJUSTMENT
•Allow the monitor to stabilize for at least 30 minutes before making image
adjustments.
3-1. How to use the ScreenManager
Use the control pad on the front panel. The control pad can be
pressed in 5 directions, “Enter”, “Up”, “Down”, “Left”and “Right”.
1. Entering the ScreenManager.
Display the ScreenManager Main menu by pressing the “Enter”of the control pad.
Up
Down
Left Right
Enter
Main menu displays the current connector type and frequency of the input signal.
2. Making Adjustments and Settings.
(1) Select the desired icon using the arrow keys.
(2) Press the Enter key to display each adjustment/setting menu.
(3) Use the control pad to make the required adjustments and settings.
(4) To save the settings and return to the Main menu, press the Enter key.
3. Exiting the ScreenManager.
To exit the ScreenManager, select the “Exit”and press the Enter key. Pushing
the down arrow key twice goes to the “Exit”position instantly.
•Leaving the ScreenManager idle for 45 seconds or more will turn the adjustment off
automatically without saving.
Main menu
Æ

3. SCREEN ADJUSTMENT 15
ENGLISH
3-2. Adjustments and Settings
Main menu Sub menu Adjustments and Settings See page
Contrast —Screen contrast and brightness*—
Size —Screen size —
Position —Screen position —
Screen Side Pin. Side pin balance —
Trapezoidal Distortion —
Tilt Inclination —
Convergence Convergence p.29) —
MoiréReduction Moirép.29) —
Fine Contrast To brighten the photo or picture image. p.16
Signal Filter To decrease the slightly shadowed
images or characters. p.16
Video Level To set the video level. p.16
Color “Standard”To set the color temperature p.29).p.17
“Custom”To adjust each color,
(Red, Green and Blue). p.17
Others PowerManager To set the power save.
(With PC’s power saving system) p.18
Off Timer To set the power save.
(With Monitor’s Off timer) p.18
Degauss To degauss P.29).p.19
Button Setting To customize the button function. p.19
Menu Position To adjust the menu position of the
ScreenManager. p.19
Input Signal To select the input signal of
Automatic or Manual. p.21
Reset To return to the factory setting. p.19
*When a black background (e.g. DOS text) is used, setting the brightness at its
maximum is recommended because a dark setting will result in eye strain due to high
character contrast.

16 3. SCREEN ADJUSTMENT
< Screen >
•To brighten the photo or picture image
< Fine Contrast >
Select “Picture Mode”.
* Select “Text Mode”to display the text on word
processor or calculating software.
* The AUTO-SIZING button can be customized to active
this function easily (See page 19).
•To decrease a slightly shadowed image or character
When the characteristics of the graphics board does not
match those of the monitor, the characters and images
displayed may have a slight shadow on their right side.
< Signal Filter >
Select from mode 1 or 2, whichever displays the image
better in the Signal Filter menu.
•To set the video level
If the setting level is improper, the screen may appear too bright or too dark.
< Video Level>
Set the video level to adapt to the output level of the PC or
the graphics board.

3. SCREEN ADJUSTMENT 17
ENGLISH
< Color >
•To set the color temperature
Temperature can be set from 4,000 K to 10,000 K, in 500 K increments.
(Including the 9,300 K default setting.)
< Temperature>
Select “Color temperature”.
“Standard”mode
•To adjust each color , (Red, Green and Blue)
Adjust the “Cutoff”p.29) and “Gain”p.29), and make appropriate color tone.
(1) First, set the monitor to maximum contrast and
brightness.
(2) < Temperature>
Set the color temperature that is close to the desired
color.
(3) < Cut off >
Adjust each color to become a uniform black level by
using the “Cutoff”function.
(4) < Gain >
Adjust each color to the desired white level by using
the “Gain”function.
(5) < Save >
Select “Save”and then press the Enter key.
The adjustment data will be lost, if the monitor is
turned off without saving.
* The values shown in percentages (%) for both the
Cutoff and Gain are available only as a reference tool.
“Custom”mode

18 3. SCREEN ADJUSTMENT
< Others >
•To set the power save
There are two power save settings choose the setting which matches your environment.
•Do your part to conserve energy, turn off the monitor when you are finished using it.
Complete energy use can only be accomplished by disconnecting the monitor’s
power supply cord from the plug receptacle.
1. With PC’s power saving system (VESA DPMS p.30))
The monitor detects the signal from the PC and executes the power saving accordingly,
as shown in the table below.
< PowerManager >
Select “On”.
Operate the mouse or keyboard to return to a normal
screen.
[Power saving system]
PC Signal Screen LED Power consumption
ON Operation Green 110 W (normal)
STAND-BY Blank screen Green 80% of normal
SUSPEND Power save (Mode 1) Flashing green Less than 10 W
OFF Power save (Mode 2) Yellow Less than 3 W
2. With Monitor’s off timer system
Without the PC’s power saving system, the off timer allows the monitor to Enter a
power save mode after a predetermined amount of time has lapsed.
< Off Timer >
Select “Enable”and press the left/right keys on the control
pad to set the “On period”. (1 to 23 hours)
Press any direction of the control pad or to turn the power
off then on again to retun to a normal screen.
[Power saving system]
Time Screen LED Power consumption
On period (1-23) Operation Green 110 W (normal)
Last 15 min. in
“On period”Advance notice* Flashing green 110 W (normal)
“On period”expired Power save mode Flashing yellow Less than 3 W
*To delay entering the power save mode, press any direction of the control pad
during the advance notice mode.

3. SCREEN ADJUSTMENT 19
ENGLISH
•To degauss the monitor
< Degauss >
Press the center of the control pad.
* The degauss circuitry takes about 30 minutes to regain
maximum power following degaussing.
•To customize the button function (Auto sizing or Fine Contrast)
< Button Setting >
Select “Auto Sizing”(Auto sizing function <See page 13>)
or “Fine Contrast”(Brighten the photo or picture image
<See page 16>).
•To adjust the menu position of the ScreenManager
< Menu Position >
Adjust the menu position as desired by using the control
pad.
•To return to the factory default setting
< Reset >
Select “Reset”.
Default settings are as follows.
Contrast and Brightness. < Contrast > 100% / 50%
Moiré.<MoiréReduction> 0%
Brighten the photo or picture image. < Fine Contrast > Text Mode
Decrease a slightly shadowed image
or character. < Signal Filter> Mode 1
Set the video level. < Video Level > 0.7V
Color temperarure. < Color > Standard /9,300K
Power save with PC’s power saving
system. < PowerManager> On
Power save with Monitor’s off timer. < Off Timer > Disable
Customize the button function. < Button Setting> Auto Sizing
Select the input signal. < Input Signal > Auto

20 3. SCREEN ADJUSTMENT
3-3. Special Function
Shortcut Keys
The brightness and contrast can be adjusted by pressing the Up, Down, Left and Right
keys of the control pad directly. Press the center of the control pad to save and exit the
settings after the adjustment.
Adjustment Lock
Use the “Adjustment Lock”function, to prevent any accidental changes.
Locked function •Adjustments and settings in the ScreenManager.
•AUTO-SIZING button.
Unlocked function •Adjustment of contrast and brightness by the shortcut keys.
•BNC/D-Sub Selection button.
•To lock
Press on the AUTO-SIZING button while switching on the monitor’s power.
•To unlock
Switch off the monitor’s power, then hold down the AUTO-SIZING button once again
and turn the power back on.