Ekookna Raff-i series User manual

ASSEMBLY INSTRUCTION

OF THE RAFF-I FAÇADE BLINDS

1.Of the raff-i façade blinds

La présente notice est composée d’une partie descriptive et d’une partie comprenant des dessins illustrant les principales

étapes de la pose. La partie avec les dessins est incluse dans la partie des instructions d’installation. Cette notice doit être

considérée comme la notice originale au regard des dispositions de la directive européenne 2006/42/CE. Ces instructions

contiennent des informations importantes sur le produit. Veuillez les lire attentivement et vous y conformer.

2.Information before the assembly

Before installing the façade blind package, its condition and correctness should be checked. Pay particular attention to the

condition of the straps and ladders (if any). The packed box and rails should be stored in a dry place until assembly. It is

forbidden to stack boxes, rest objects on boxes or place items on boxes. Prior to installation, the condition of the building’s

facade should be assessed. If necessary, additionally attach the box or guides directly to the building or façade. Additional

reinforcements of the RAFF-i box must be attached to the lintel of the building. The façade blind package may only be

installed in the RAFF-i box when it is in a technically perfect condition. No additional structural elements or non-system ﬁxings

may be mounted on the box. They can adversely affect the function of the façade blinds and lead to damage to it. The end

positions of the façade blind package are preset. In case of de-programming, they must be set again in accordance with the

manual of the motor used in the façade blind package.

During installation, the health and safety regulations must be observed. The RAFF-i box should be installed by at least 2 pe-ople.

Electrical installations must be performed by authorized electricians in accordance with the requirements of the country where

the installation takes place. When working at greater heights, installers and construction elements must be secured against

falling. Some components of the RAFF-i system can be cut from sharp edges!

ASSEMBLY INSTRUCTION

OF THE RAFF-I FAÇADE BLINDS

3.Installation of the façade blind

In order for the façade blinds to meet its technical properties, the correct production process and correct assembly are im-

portant.

EXAMPLES OF CONSTRUCTION VARIANTS

On the reveal in the version of a

visible box.

On the reveal in the ﬂush-mounted

version of the box.

On the wall in a ﬂush-mounted

version.

On the wall in the visible version.

On the window in the visible

version with the use of offsets.

On the window in the visible

version with the use of offsets at the

back and front (e.g., for a recess).

ASSEMBLY INSTRUCTION

OF THE RAFF-I FAÇADE BLINDS

ASSEMBLY OF THE GUIDE ON THE SIDE

Drill mounting holes on the side of the guide in the numbers

shown below, depending on the length of the guide.

With the guide bar length:

≤ 150 cm: 2 ﬁxings on the FS

≤ 250 cm: 3 ﬁxings on the FS

> 250 cm: 5 ﬁxings on the FS

> 300 cm: 7 ﬁxings on the FS

Attach the MONOBLOK EKOOKNA

Aluminum guide to the side of the façade or other surface

using assembly screws (not included in the set). Plug from

the front with the enclosed aluminum proﬁle.

Ø10

Ø5

FRONT GUIDE MOUNTING

Drill mounting holes in the guide from the front in the

numbers shown below, depending on the length of the

guide.

With the guide bar length:

≤ 150 cm: 2 ﬁxings on the FS

≤ 250 cm: 3 ﬁxings on the FS

> 250 cm: 5 ﬁxings on the FS

> 300 cm: 7 ﬁxings on the FS

Mount the MONOBLOK EKOOKNA

Aluminum guide on the façade or window frame using

assembly screws (not included). Plug from the front with

the enclosed aluminum proﬁle.

Ø10

Ø5

ASSEMBLY INSTRUCTION

OF THE RAFF-I FAÇADE BLINDS

Place the box from the top. There are special pins

protruding from the box, which just need to be inserted

into previously mounted guides.

Attach the MONOBLOK EKOOKNA aluminum

guide to the side of the façade or other surface using

assembly screws (not included in the set). Plug from the

front with the enclosed aluminum proﬁle.

In the case of additional system reinforcements of the

RAFF-i boxes, attach the box to the lintel.

Mounting screws are not included.

ASSEMBLY INSTRUCTION

OF THE RAFF-I FAÇADE BLINDS

HOW TO ASSEMBLE THE REVISION HATCH:

Attach the box cover plates to the side covers with rivets in accordance with the drawings below.

10-15mm25mm

25mm

10-15mm

50mm

10-15mm

50mm

* Alternative method of mounting the revision hatch

The front wall of the box (revision hatch) can be ﬁxed

with a fastening element in the side wall of the box.

ASSEMBLY INSTRUCTION

OF THE RAFF-I FAÇADE BLINDS

Place the façade blind package in the box. The pac-

ka-ge should be attached to the box with automatic

grips installed inside the box on the side walls and on

ad-ditional box reinforcements.

Insert the PVC guide in such a way that the guides of the

façade shutter set are inside it.

TIPS:

◾Press the PVC guide so that it is seated

in the aluminum MONOBLOK EKOOKNA guide.

◾The PVC guide should be disassembled before

removing the package from the RAFF-i box again.

Correctly mounted set of blinds in the PVC guide, inside

the RAFF-i system box.

38 mm

Attach the guide to the box, as shown in the

graphic below.

ASSEMBLY INSTRUCTION

OF THE RAFF-I FAÇADE BLINDS

ASSEMBLY INSTRUCTION

OF THE RAFF-I FAÇADE BLINDS

Guide

MONOBLOCK von EKOOKNA Guide

RAFF-e (A 45)

27

92

DIVIDER guide

TYP 4

22,5

21,1

40

70-90

20

92

27

Guide

PVC (A 40)

ASSEMBLY INSTRUCTION

OF THE RAFF-I FAÇADE BLINDS

______________________________________________________________________________________

All ﬁgures are indicative only

and may not fully represent the actual product.

NOTES

www.ekookna.com

Eko-Okna S.A. ul. Spacerowa 4 47-480 Kornice

01/2022

EkoOkna RAFF-I Series User manual

Popular Window Blind manuals by other brands