ELAC Debut Reference DBR62 User manual

,OPERATING INSTRUCTIONS
I lA( The ljfe of sound.

Safety Instructions
1. General information
Please read and follow these safety instructions.
Keep them safe for future reference.
Observe all warnings on the speaker and in the manual. Please check the speaker for damage before
use. The speaker must be in perfect working condition. Damaged parts may lead to personal injury.
2. Use only as directed
Connect the speaker(s) according to the instructions in the manual.
• Many ELAC speakers are equipped with spikes and/or anti-slip feet. They are explicitly provided for
levelling the speaker. For levelling on an uneven floor, unscrew the spikes or anti-slip feet by 2-3 turns of
thread. The speaker should always be in perfect vertical alignment: the stability of the speaker must not
be compromised by using spikes or anti-slip feet as the speaker may tip-over.
3. Location
Install the speakers on a level surface only
When choosing the location of these speakers do not place them in locations that are:
In direct sunlight
Very humid
Prone to vibrations
Exceptionally hot or cold
Near CRT Televisions (the speakers are not magnetically shielded and may cause color issues
with a CRT based TV)
Close to magnetic cards (Since the speakers are not magnetically shielded placing magnetic
cards such as credit cards or commuter cards may cause them to fail).
WARNING! Please ensure the product is perfectly stable to avoid injury from tip-over. Please note, that stability
can be increased by using spikes on carpeted surfaces. However, the mounting of spikes must be carried out
carefully due to their very sharp ends which may cause injuries. The stability on slippery floors can be increased
by using Velcro fastening tape or double-sided adhesive tape. Do not install the speaker near any heat sources
such as radiators, heating valves, stoves, or other apparatus (including amplifiers) that produce heat, or in areas
where there is a risk of explosion.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Do not install the speaker in a closed rack or in a closed cupboard.
Do not put burning candles on or near the speaker.
Do not install the speaker near transformers because electromagnetic stray fields can cause hum noise
on woofers.
In combination with certain materials / lacquers / material surfaces, anti-slip feet or spike washers may
cause colored imprints on the surfaces.
4. Overload
Extreme overload of the device due to very high volume may cause damage to individual components.
Because of the possible danger, you should never leave loudspeakers under extreme overload
conditions unattended.
ELAC Debut Reference Speakers Iwww.elac.com I Page 1

5. Service
DANGER! Do not open the cabinet because the components and conductors may carry current!
Servicing to be carried out by qualified service personnel only.
Servicing is required when the loudspeaker has been damaged in any way, such as damage to
the power supply cord or the plug, or when liquid has been spilled or objects have fallen onto the
loudspeaker, the speaker has been exposed to rain or moisture, does not operate normally, or has been
dropped. To reduce the risk of electric shock, do not open the loudspeaker. Servicing should be carried
out by qualified service personnel only.
6. Cleaning
NOTE: Clean only with soft, smooth cloth or with dust brush. Do not use scouring agents, alcohol,
benzene, furniture polish or other agents for cleaning! Modern furniture is often coated with multiple
varnishes and plastics which can be treated with chemical agents. Some of these agents contain
substances which degrade or soften the rubber feet. Therefore we advise that you place an anti-slip mat
underneath the loudspeaker(s).
7. Volume
CAUTION! Continuous high volume may cause severe damage to your hearing. Please listen responsibly.
8. Disposal
The packaging is made from recyclable materials. Dispose of this in an environmentally friendly manner.
At end of life do not dispose of the speaker(s) with standard household waste. The speaker must be
recycled in accordance with local legislation. Ask your local government for further information on
recycling as the device contains valuable raw materials. Disable the speaker(s) before disposal.
ELAC Debut Reference Speakers Iwww.elac.com I Page 2

Philosophy
Thank you for purchasing this ELAC product.
Since the time we started (1926), ELAC has always striven to achieve the very best.
Your new ELAC speakers are built to the highest standards using high-quality components that are carefully
constructed to deliver the best-in-class sound quality. They are developed by a passionate group of individuals
whose soul purpose is to bring a new dimension of sound quality into your home. Enjoy!
Before Use
Avoid damage to the speakers and other components:
Carefully unbox the speakers carefully to avoid physically damaging your speakers.
Use appropriate gauge wires (minimum of 16 gauge wire for runs up to 25 feet).
Make sure wire polarity is connected correctly. Most speaker cables are coded for ease of use. Make
sure positive (red) connection on the amplifier terminal is connected to the positive (red) on your
speakers. Follow the same instructions for the negative side. Strip off approximately 1/2"ofthe insulation
from the ends of the speaker cable, twist the bare strands and insert into the binding post.
Ensure your equipment is turned off before connecting speakers.
Check to ensure positive and negative wires are not touching each other once they're connected to the
speaker terminals.
Amplifier Terminals
ELAC Debut Reference Speakers Iwww.elac.com I Page 3

Feet & Spike Installation (DFR52 Only)
Using the included feet provide a wider support base for speaker cabinet. The included spikes improve stability
on uneven surfaces and thickly carpeted floors. Please, use cution when dealing with spikes as they are sharp.
IMPORTANT! In order to prevent scratching or damage the cabinet, turn the speaker upside down onto a soft
surface while you attach the outrigger feet and spikes. We highly recomend a second person help with this
process.
A. Attach the feet with provided machine screws (see fig.A).
8. Screw in the spikes as shown in FIG.B. The speaker can now be
turn back over . Please, be careful when handling the speaker with
the spikes installed. If you have hard wood tile floors, please usethe
provided floor discs (fig. B).
C. Using the supplied alien wrench adjust the height of the spikes until
the speaker sits level and all four spikes are toching the floor (fig.C).
D. Once the speaker is level, use the supplied covers to lock the
spikes into place (fig.D).
ELAC Debut Reference Speakers Iwww.elac.com I Page 4
FIG.A
FIG .B
FIG .C
FIG .D

Installing and Removing the Grills
The mesh grills of your Debut Reference speakers are designed to be removable if desired. To remove it, hold
the top or bottom edges of the grill and pull gently. To replace the grill, align the edges of the grills with the
edges of the cabinet. The grill will be positioned and hold in place by the magnets incorporated in the grill.
IMPORTANT!
ELAC DFR52 Floorstanding Speakers Safety Clip
The ELAC DFR52 Floorstanding speakers include a safety clip in the accessories bag. Install this safety clip
on back of the cabinet for securing the cabinet to a wall to prevent tip-over. Use support hooks (not included)
screwed into a wall and pass appropriate size cord (not included) around the hook and through the safety clip.
Test to ensure mounted hooks and cord will prevent tipping of the speaker.
CAUTION:
DFR52 Floorstanding Speaker
Safety Clip (provided as
accessories)
Support Hooks & Cords
(not included)
Wall
The safety clip is not a mounting fixture and the speaker should not be hung on the wall using the clip. ELAC
does not claim responsibility for damage resulting from improper assembly, installation, insufficient strength of
the installation materials, misuse, or natural disasters.
ELAC Debut Reference Speakers Iwww.elac.com I Page 5

Speaker Placement
Achieve maximum performance and optimal sound quality from your ELAC Reference speakers with proper
speaker placement and set-up. While not all rooms are the same, use the following guidelines to configure the
speakers for your particular room. There are no "exact" rules or boundaries in setting up your speakers but the
following suggestions will help optimize your desired results. Remember the best sound set-up is what sounds
best for you so don't be afraid to experiment and make adjustments to the placement and directivity of the
speakers.
FIG . 1
•
•
I
Place the speakers approximately one to two feet away (fig. 1) from boundaries such as wall(s) and especially
corners. Close proximity to a side or rear wall will enhance bass performance (output), but being too close
(particularly to a corner) may result in bass that is unnatural. If a corner location is unavoidable, try to position the
loudspeaker so that the distance to the rear wall is not equal to the distance to the side wall.
ELAC Debut Reference Speakers Iwww.elac.com I Page 6

Stereo Setup
For the best results and the most realistic stereo image and lifelike sound, place the speakers so that an
equilateral triangle (fig. 2) is created between the speakers and your favorite listening position. This set
up creates the optimum imaging performance.
If you find that your DBR62 or DFR52 left and right speakers are too far apart, angle (toe in) them
towards the listening position to gain a more focused central image.
Left Speaker Right Speaker
TV & Center Speaker
• : : I [w .::, .
.: . · "" · .;; . . :
. . ............................................................................ , .. , .............. : .
Listening Position
FIG. 2
ELAC Debut Reference Speakers I www.elac.com I Page 7

Surround Sound Setup
Whether you use the DBR62 bookshelf or the DFR52 floorstanding speakers for a 5.1-channel surround set-up,
avoid placing the surround speakers forward of your listening position. The surround speakers should be spread
apart wider than the front speakers. In addition, elevate the speakers to the same height or slightly higher as the
front speakers for the most enveloping sound field. Like the front speakers, you may need to experiment with
the positioning by pointing the rear surround speakers towards the listening area.
I cc.J) I
: _____ .c:=::;::;J.. _____ :
Left Rear
Surround
.,.
_f
5.1 -Channel Surround Set-Up
ELAC Debut Reference Speakers Iwww.elac.com I Page 8
Right Rear
Surround

Center Speaker Setup
The ELAC DCR52 center channel speaker is designed to produce dialog sounds and should be positioned
above or below (fig. 3) your television. Align it with the center of the television. As much as possible, try to keep
the DCR52 close to the same level (height) as your front speakers for a more even sound stage. Keeping the
same height for the center channel can be very challenging so it might be necessary to tilt the center speaker
up (if too low) or down (if too high), to aim it towards the listening area.
[]
Place Above
or Below
1 □---
~ --
-
I ----
I
I
L
I
I
I
L - - --
----------
- - -
Television
----------------
..,..
(
I
--
--- - - -- - -
Optimal results for the center are obtained by setting the receiver/processor center channel size to small. If you
have a choice, set the crossover frequency to 80Hz.
ELAC Debut Reference Speakers Iwww.elac.com I Page 9

SPECIFICATIONS
Model DBR62 DCR52 DFR52
Bookshelf Speaker Center Channel Speaker Floorstanding Speaker
Enclosure Type 2-Way Bass Reflex 2 - Way Bass Reflex 3-Way Bass Reflex
Frequency Response
44Hz-35000Hz
55Hz - 35000hz
42Hz-35000Hz
Nominal Impedance 6 Ohms 8 Ohms 6 Ohms
Sensitivity
86db @2.83v/1m 87db@ 2.83v/1m 87db @2.83v/1m
Crossover Frequency 2200Hz 2200Hz 90hz/2200Hz
Max Power Input 120 Watts 120 Watts
140 Watts
Tweeter
1" Cloth Dome 1" Cloth Dome
1" Cloth Dome
Midrange n/a n/a 5.25 Inch Aramid Fiber
Woofer 6.5 Inch Aramid Fiber 2 x 5.25 Inch Aramid Fiber 2 x 5.25 Inch Aramid Fiber
Cabinet CARB2 Rated MDF CARB2 Rated MDF CARB2 Rated MDF
Cabinet Finish White Baffle, Oak Cabinet or White Baffle, Oak Cabinet or White Baffle, Oak Cabinet or .
Black Baffle, Wallnut Cabinet Black Baffle, Wallnut Cabinet Black Baffle, Wall nut Cabinet
Port Dual Flared 3 x Dual Flared 3 x Dual Flared
Binding Posts 5-Way Metal 5-Way Metal 5-Way Metal
Dimensions (WxHxD) 8.18" X 10.82" X 14.13"
20.74" X 9.52" X 7.28" 7.28" X 9.52" X 39.99"
Weight (lb / Kg) 18.07 / 8.2 22.26 I 10.1 36.81 / 16.7
ELAC Debut Reference Speakers I www.elac.com I Page 10

ELAC Americas Inc.
North America Limited Liability Warranty
Passive Speakers (No Built-in Amplifier)
ELAC Americas Inc. warrants to the original purchaser that this product be free from defects and or workmanship
for a period of 3 (Three) years from the original date of purchase. During this time period, repair or replacement
of parts will be free of charge to the original owner (See below limitations). Shipping to and return from the repair
center will be the responsibility of the original purchaser.
Limitations
Warranty begins on the date of original purchase from an authorized ELAC Americas Inc. dealer.
• Product is warranted only if used in home applications within the max power rating specified in this
manual. Commercial use of this product is not warranted.
Product that has been modified or altered in anyway will not be warranted.
Product that has been abused or subjected to faulty equipment will not be warranted.
Products with defaced or removed serial numbers will not be warranted.
Ifservice is required
In the event that service is required, please contact ELAC America at 888-541-0996 or at
[email protected] to arrange for service or replacement. You will be responsible to provide proof of
purchase (Copy or original sales receipt). Shipping to and from our repair center will be the responsibility of the
original purchaser.
Warranty Outside of North America
This warranty applies to products purchased in the United States and Canada. For warranty claims outside of
North America please contact the local dealer/distributor in the country of purchase.
ELAC Debut Reference Speakers Iwww.elac.com I Page 11