Elatec TWN4 MultiTech 2 HF Use and care manual

TWN4 MULTITECH 2 LEGIC M
LF HF
INTEGRATION MANUAL

TABLE OF CONTENTS
1INTRODUCTION.................................................................................................................................................................. 3
1.1 ABOUT THIS MANUAL ..................................................................................................................................................3
1.2 ABOUT TWN4 MULTITECH 2 LEGIC M LF HF .............................................................................................................3
1.3 ELATEC SUPPORT........................................................................................................................................................3
1.4 REVISION HISTORY......................................................................................................................................................3
2SAFETY INFORMATION ..................................................................................................................................................... 4
3INTEGRATION INSTRUCTIONS......................................................................................................................................... 5
3.1 GENERAL.......................................................................................................................................................................5
3.2 LIST OF APPLICABLE RULES ......................................................................................................................................5
3.3 SPECIFIC OPERATIONAL USE CONDITIONS.............................................................................................................5
3.4 LIMITED MODULE PROCEDURES ...............................................................................................................................5
3.5 TRACE ANTENNA DESIGN...........................................................................................................................................5
3.6 RF EXPOSURE CONSIDERATIONS.............................................................................................................................5
3.7 ANTENNAS ....................................................................................................................................................................4
3.8 LABEL AND COMPLIANCE INFORMATION .................................................................................................................4
3.9 TEST MODES AND ADDITIONAL TESTING REQUIREMENTS...................................................................................4
3.10 ADDITIONAL TESTING, PART 15 SUBPART B DISCLAIMER.....................................................................................4
3.11 MECHANICAL INSTALLATION......................................................................................................................................4
3.12 ELECTRICAL CONNECTION.........................................................................................................................................5
3.13 PROGRAMMATION/SOFTWARE INTEGRATION ........................................................................................................5
4COMPLIANCE STATEMENTS ............................................................................................................................................ 6
4.1 EU ...................................................................................................................................................................................6
4.2 FCC.................................................................................................................................................................................6
4.3 IC ....................................................................................................................................................................................6
4.4 UNITED KINGDOM ........................................................................................................................................................7
4.5 RF EXPOSURE COMPLIANCE .....................................................................................................................................7
5INTEGRATOR AND HOST REQUIREMENTS .................................................................................................................... 8
APPENDIX ....................................................................................................................................................................................... 9
A – TERMS AND ABBREVIATIONS...........................................................................................................................................9
B – RELEVANT DOCUMENTATION ..........................................................................................................................................9

© 2022 ELATEC GmbH – TWN4 MultiTech 2 LEGIC M LF HF integration manual DocRev2 – 07/2022 Page 3of 12
1INTRODUCTION
1.1 ABOUT THIS MANUAL
This integration manual explains how to integrate ELATEC RFID reader/writer module TWN4 MultiTech 2 LEGIC M LF HF into a host
device and is mainly intended for integrators and host manufacturers. Before installing the product, the integrators should read and
understand the content of this integration manual and other relevant installation documents.
The content of this integration manual is subject to changes without prior notice and printed versions might be obsolete. Integrators
and host manufacturers are required to use the latest version of this integration manual.
For the sake of better understanding and readability, this manual might contain exemplary pictures, drawings and other illustrations.
Depending on your product configuration, these pictures might differ from the actual design of your product.
The original version of this integration manual has been written in English. Wherever the integration manual is available in another
language, it is considered as a translation of the original document for information purposes only. In case of discrepancy, the original
version in English will prevail.
1.2 ABOUT TWN4 MULTITECH 2 LEGIC M LF HF
ELATEC TWN4 family of RFID readers and writers allows users to read and write to almost any 125 kHz and 13.56 MHz tags and/or
labels – it supports all major transponders from various suppliers like ATMEL, EM, ST, NXP, TI, HID, LEGIC, etc. and ISO standards
like ISO 14443A/B (T=CL), ISO 15693, ISO 18092 / ECMA-340 (NFC).
The TWN4 MultiTech 2 LEGIC M LF HF reader module has integrated RFID (LF & HF) and NFC, which is supported by mobile phones
with Android version 4.3 or greater. The app on the reader communicates with the NFC module with easy commands.
1.3 ELATEC SUPPORT
In case of any technical questions, refer to the ELATEC website (www.elatec.com) or contact ELATEC technical support at
[e-mail]
1.4 REVISION HISTORY
VERSION
CHANGE DESCRIPTION
EDITION
02
Product picture and chapter “Antennas” updated
07/2022
01
First edition
06/2022

© 2022 ELATEC GmbH – TWN4 MultiTech 2 LEGIC M LF HF integration manual DocRev2 – 07/2022 Page 4of 12
2SAFETY INFORMATION
•ELATEC TWN4 MultiTech 2 LEGIC M LF HF is an electronic component and should be installed exclusively by a trained and
qualified personnel.
•ELATEC recommends the integrators to follow general ESD protective measures during the installation of TWN4 MultiTech 2
LEGIC M LF HF into a host device, e.g. the use of an antistatic wristband or special gloves.
•The integrator should not touch the antennas (if not shielded), printed circuit boards, connectors or other sensitive components on
TWN4 MultiTech 2 LEGIC M LF HF.
•Metallic materials on or in direct vicinity to the product might reduce the reading performance of the product. Refer to the installation
instructions for more information.
•Before installing TWN4 MultiTech 2 LEGIC M LF HF into a host device, the integrator should also make sure that he/she has read
and understood the ELATEC technical documentation related to TWN4 MultiTech 2 LEGIC M LF HF, as well as the technical
documentation related to the host device. In particular, the instructions and safety information given in the user manual of
TWN4 MultiTech 2 LEGIC M LF HF should be read carefully and listed in the technical documentation of the host manufacturer as
well, as soon as these instructions and safety information are required for a safe and proper use of the host device containing
TWN4 MultiTech 2 LEGIC M LF HF.
•Any failure to comply with the safety information given in this document and in the user manual, is considered improper use.
ELATEC excludes any liability in case of improper use or faulty product installation.

© 2022 ELATEC GmbH – TWN4 MultiTech 2 LEGIC M LF HF integration manual DocRev2 – 07/2022 Page 5of 12
3INTEGRATION INSTRUCTIONS
3.1 GENERAL
TWN4 MultiTech 2 LEGIC M LF HF may be installed in any host devices, as long as it is operated under the operational conditions
stated in the user manual and other technical documents (e.g. data sheet). TWN4 MultiTech 2 LEGIC M LF HF is equipped with two
integrated antennas. Thus, no antenna installation is required.
3.2 LIST OF APPLICABLE RULES
Refer to the approval certificates, grants and declarations of conformity issued for TWN4 MultiTech 2 LEGIC M LF HF, and to the
following rules applicable to TWN4 MultiTech 2 LEGIC M LF HF:
•47 CFR 15.207
•47 CFR 15.209
•47 CFR 15.225
•RSS-Gen
•RSS-102
•RSS-210
3.3 SPECIFIC OPERATIONAL USE CONDITIONS
There are no specific operational use conditions for TWN4 MultiTech 2 LEGIC M LF HF other than the conditions mentioned in the
user manual and data sheet of TWN4 MultiTech 2 LEGIC M LF HF. The host manufacturer or integrator must ensure that these use
conditions comply with the use conditions of the host device. In addition, these use conditions must be stated in the user manual of
the host device.
3.4 LIMITED MODULE PROCEDURES
n/a
3.5 TRACE ANTENNA DESIGN
n/a
3.6 RF EXPOSURE CONSIDERATIONS
The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 0 cm and any additional testing
and authorization process as required.
Refer to Chapter “Compliance Statements” for detailed information about the radio frequency exposure conditions applicable to
TWN4 MultiTech 2 LEGIC M LF HF.
These RF exposure conditions must be stated in the end-product manual(s) of the host product manufacturer.

© 2022 ELATEC GmbH – TWN4 MultiTech 2 LEGIC M LF HF integration manual DocRev2 – 07/2022 Page 4of 12
3.7 ANTENNAS
The reader module is equipped with the following antennas:
TWN4 MultiTech 2 LEGIC M LF HF
(exemplary picture)
HF antenna (13.56 MHz)
Dimensions: 42 x 47 mm / 1.65 x 1.85 inch
Number of turns: 3
LF antenna (125 kHz)
Diameter: 16 mm / 0.63 inch
Number of turns: 120
For more information, refer to the related product data sheet or
other relevant technical documents.
3.8 LABEL AND COMPLIANCE INFORMATION
Refer to Chapters “Compliance Statements” and “Integrator and Host Requirements” for detailed label and compliance information.
3.9 TEST MODES AND ADDITIONAL TESTING REQUIREMENTS
No specific testing method has been defined by ELATEC for TWN4 MultiTech 2 LEGIC M LF HF.
TWN4 MultiTech 2 LEGIC M LF HF has been tested and found in compliance with the specifications noted on the approval certificates
and other relevant approval documents. However, the integrator is still responsible for any additional testing and authorization process
required for the end product.
It is recommended that the host product manufacturer installing the modular transmitter perform some investigative measurements to
confirm that the resulting composite system does not exceed the spurious emissions limits or band edge limits (e.g., where a different
antenna may be causing additional emissions). Detailed information regarding test procedure are described in the relevant rule parts
(refer to Chapter “List of applicable rules”).
3.10 ADDITIONAL TESTING, PART 15 SUBPART B DISCLAIMER
TWN4 MultiTech 2 LEGIC M LF HF is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant,
and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the
modular transmitter grant of certification. In addition, the final host product still requires Part 15 Subpart B compliance testing with
TWN4 MultiTech 2 LEGIC M LF HF installed.
3.11 MECHANICAL INSTALLATION
The module can be fixed with four screws M2.5.

© 2022 ELATEC GmbH – TWN4 MultiTech 2 LEGIC M LF HF integration manual DocRev2 – 07/2022 Page 5of 12
3.12 ELECTRICAL CONNECTION
The module can be connected to the host with a DF11 connector*.
PIN
PIN NAME
FUNCTION
1
UGND
USB Ground. Fed to main Ground through noise-reduction circuit.
2
USB_D+
USB Data +
3
UVCC
USB VCC (5V). When using RS-232, connect this to external 5V supply.
4
USB_D-
USB Data -
5
V24_RXD
RS-232 RXD (Input)
6
GND
Ground
7
V24_TXD
RS-232 TXD (Output)
8
Hostsense
Active-low, enables RS-232 transceiver. Short to Pin 6 (GND) when using RS-232.
*Hirose DF11 series, 2mm pitch or type equivalent. In case the reader module is not connected with a cable delivered by ELATEC,
the reader module can only be connected with a cable equipped with the following connector:
Manufacturer: Shenzhen Le Qing Lin Hai Electronics Co., Ltd
Part no.: A2002-H04X2
3.13 PROGRAMMATION/SOFTWARE INTEGRATION
n/a

© 2022 ELATEC GmbH – TWN4 MultiTech 2 LEGIC M LF HF integration manual DocRev2 – 07/2022 Page 6of 12
4COMPLIANCE STATEMENTS
4.1 EU
TWN4 MultiTech 2 LEGIC M LF HF is in compliance with the EU directives and regulations as listed in the respective declaration of
conformity.
4.2 FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Caution
The Federal Communications Commission (FCC) warns the users that changes or modifications to the unit not expressly approved by
the party responsible for compliance could void the user's authority to operate the equipment.
FCC §15.105 (b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the Receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
FCC ID: WP5TWN4F22
4.3 IC
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.
IC: 7948A-TWN4F22

© 2022 ELATEC GmbH – TWN4 MultiTech 2 LEGIC M LF HF integration manual DocRev2 – 07/2022 Page 7of 12
4.4 UNITED KINGDOM
TWN4 MultiTech 2 LEGIC M LF HF complies with the requirements of the UK legislations and other regulations as listed in the
respective UK declaration of conformity. The importer is responsible for applying the following information to the packaging of the
product:
•the importer company’s details, including the company’s name and a contact address in the United
Kingdom.
•UKCA marking
4.5 RF EXPOSURE COMPLIANCE
RF exposure statement (mobile and fixed devices)
This device complies with the RF exposure requirements for mobile and fixed devices. However, the device shall be used in such a
manner that the potential for human contact during normal operation is minimized.

© 2022 ELATEC GmbH – TWN4 MultiTech 2 LEGIC M LF HF integration manual DocRev2 – 07/2022 Page 8of 12
5INTEGRATOR AND HOST REQUIREMENTS
Authorization requirements
TWN4 MultiTech 2 LEGIC M LF HF has been certified as a module and does not need further approval, provided that the module is
used in accordance with the FCC grant conditions and no limitations or usage conditions have been defined by ELATEC. However,
the host manufacturer must ensure that the host device still complies with all applicable regulations after TWN4 MultiTech 2 LEGIC M
LF HF has been integrated.
In particular, the host integrator installing TWN4 MultiTech 2 LEGIC M LF HF into their product must ensure that the final composite
product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter
operation and should refer to guidance in KDB 996369.
Labeling requirements
Using a permanently affixed label, TWN4 MultiTech 2 LEGIC M LF HF must be labeled with its own FCC and IC identification numbers.
In case this label is not visible anymore after integration of TWN4 MultiTech 2 LEGIC M LF HF in the host device, it is necessary to
bring a label on the host device (on a visible and accessible place) stating the FCC and IC identification numbers of the integrated
TWN4 MultiTech 2 LEGIC M LF HF:
Contains FCC ID: WP5TWN4F22
Contains IC: 7948A-TWN4F22
In case several modules have been integrated into the host device, the label should state all FCC and IC identification numbers of the
integrated modules.
Example:
“Contains FCC IDs: XXX-XXXXXXX, YYY-YYYYYYY, ZZZ-ZZZZZZZ”
“Contains transmitter modules IC: XXXXX-XXXXXX, YYYYY-YYYYYY, ZZZZZ-ZZZZZZ”
Compliance statements
All statements listed in Chapter “Compliance statements” of this integration manual must be also listed in the user manual of the host
device.
Special accessories
Where special accessories such as shielded cables and/or special connectors are required to comply with the emission limits, the
instruction manual shall include appropriate instructions on the first page of the text describing the installation of the device.
Simultaneous transmission
When the host product supports simultaneous-transmission operations the host manufacturer needs to check if there are additional
RF exposure filing requirements due to the simultaneous transmissions. When additional application filing for RF exposure compliance
demonstration is not required (e. g. the RF module in combination with all simultaneously operating transmitters complies with the RF
exposure simultaneous transmission SAR test exclusion requirements), the host manufacturer may do his own evaluation without any
filing, using reasonable engineering judgment and testing for confirming compliance with out-of-band, restricted band, and spurious
emission requirements in the simultaneous-transmission operating modes. If additional filing is required please contact the person at
ELATEC GmbH responsible for certification of the RF module.

© 2022 ELATEC GmbH – TWN4 MultiTech 2 LEGIC M LF HF integration manual DocRev2 – 07/2022 Page 9of 12
APPENDIX
A – TERMS AND ABBREVIATIONS
TERM EXPLANATION
host device
Also “host” or “host product”. Device in which an RFID module is intended to be installed for operation.
Integrator
Responsible party for the integration of an RFID module into a host device. The integrator might be the
module manufacturer, the host manufacturer, the end user or any other third party.
KDB
Knowledge Database
modular type
Physical configuration in which a modular transmitter operates when installed within a host device. It can
be a single-modular, a limited single-modular, a split-modular or a limited split-modular type.
n/a
Not applicable
RFID (reader/writer)
module
Device intended to be used within another device or product. Depending on the equipment configuration
and intended use, an RFID module has to meet different requirements to get a modular grant.
B – RELEVANT DOCUMENTATION
ELATEC documentation
•TWN4 MultiTech 2 LEGIC M LF HF data sheet
•TWN4 MultiTech 2 LEGIC M LF HF functional description
•TWN4 MultiTech 2 LEGIC M LF HF user manual
External documentation
Document name
Document title/description
Source
n/a
Technical documentation related to the
host product
Host product manufacturer
784748 D01 General labeling and
Notification
General Guidelines for Labeling and
Other Information Required to be
Provided to Users
Federal Communications Commission
Office of Engineering and Technology
Laboratory Division
996369 D01 Module Equip Auth Guide Transmitter Module Equipment
Authorization Guide
Federal Communications Commission
Office of Engineering and Technology
Laboratory Division
996369 D02 Module Q and A Frequently Asked Questions and
Answers about Modules
Federal Communications Commission
Office of Engineering and Technology
Laboratory Division
996369 D03 OEM Manual
Guidance for Modular Transmitter
Instruction Manuals and TCB
Certification Application Reviews
Federal Communications Commission
Office of Engineering and Technology
Laboratory Division
996369 D04 Module Integration Guide
Modular Transmitter Integration Guide—
Guidance for Host Product
Manufacturers
Federal Communications Commission
Office of Engineering and Technology
Laboratory Division
RSS-Gen
General Requirements for Compliance of
Radio Apparatus
Innovation, Science and Economic
Development Canada
RSS-102
Radio Frequency (RF) Exposure
Compliance of Radiocommunication
Apparatus (All Frequency Bands)
Innovation, Science and Economic
Development Canada
RSS-210
Licence-Exempt Radio Apparatus:
Category I Equipment
Innovation, Science and Economic
Development Canada
Title 47 of the Code of Federal
Regulations (CFR)
FCC’s rules and regulations Federal Communications Commission
For more information about this integration manual or TWN4 MultiTech 2 LEGIC M LF HF, go to www.elatec.com or contact
ELATEC.

Elatec reserves the right to change any information or data in this document without prior notice. Elatec declines all responsibility for the use of this product with any other specification but the one mentioned above. Any
additional requirement for a specific customer application has to be validated by the customer himself at his own responsibility. Where application information is given, it is only advisory and does not form part of the
specification. Disclaimer: All names used in this document are registered trademarks of their respective owners.
© 2022 ELATEC GmbH – TWN4 MultiTech 2 LEGIC M LF HF integration manual DocRev2 – 07/2022
ELATEC GMBH
Zeppelinstr. 1
•82178 Puchheim •Germany
P [phone]
•F [phone] •E-mail: [e-mail]
elatec.com