Elecro Engineering Spectrum Hybrid SH-55 Installation instructions

Spectrum Hybrid
UV + Hydroxyl Radical Pool Sanitiser
Installation & Operating Manual

ENGLISH
www.elecro.co.uk

ENGLISH
1
www.elecro.co.uk
Important Notes
Congratulations on purchasing the Spectrum Hybrid UV + HO pool
sanitising system, the latest in UV technology, manufactured in England to
the highest standards.
To ensure your new product will give years of trouble free service please
carefully read the following instructions.
Incorrect installation will aect your warranty. Do not discard this
manual, please retain for future reference.
Important safety information
• Consult a qualied electrician
• Never look directly at an illuminated UV lamp
• Do not run this unit dry, do not cover this unit
• Always isolate the unit from mains electricity and turn o the water
supply before carrying out maintenance
• Always disconnect all pool appliances from the mains electricity supply
before servicing
• Power must be supplied through a Residual Current Device (RCD) with
a rated residual operating current not exceeding 30mA
• This unit must be earthed. Never use a higher rated fuse than specied
• The unit must not be submerged in water
• If the quartz sleeve is cracked, replace it immediately
• Young children should always be supervised near water
Specication
Model: SH-55 & SH-110 (Analogue); SHP-55 & SHP-110 (Digital)
Rating: 220~240V 50/60Hz; 110~120V 50/60Hz
MAX Pressure = 3 Bar
This unit is manufactured in conformance with:
Safety: BS EN 60335-1:2002. BS EN 60335-2-55:2003
EMC: EN 55015: 2000. EN 61000-3-2: 2000 EN 61000-3-3: 1995.
EN61547:1995
This unit is CE approved.

ENGLISH
www.elecro.co.uk
2
Product Overview
The Spectrum Hybrid is available in 55W single tube and 110W double
tube formats, supplied complete with ow switch and either an analogue
lamp life indicator and reset switch, or digital lamp life countdown with
intelligent dosing pump.
Fig 1.
FLOWTUBE COVER
CONTROL BALLAST
ASSEMBLY
BULB RETAINING
CLIP
BULB CAP
LOCKING NUT ‘O’ RING
UV BULB
QUARTZ GLASS
SLEEVE
REAR WALL
BRACKET
FRONT WALL
BRACKET
BRACKET FIXING
SCREWS
ELECTRONIC
CONTROLLER ASSEMBLY
MANIFOLD
ASSEMBLY
55W Single Tube Unit
Note: Digital Model Shown

2
www.elecro.co.uk
ENGLISH
FLOWTUBE COVER
UV LAMP RETAINING
CLIP
LOCKING NUT
‘O’ RING
UV LAMP
QUARTZ GLASS
SLEEVE
BRACKET
ELECTRONIC
CONTROLLER ASSEMBLY
UV LAMP CAP
CONTROL BALLAST
ASSEMBLY
MANIFOLD
ASSEMBLY
Fig 2.
110W Double Tube Unit
3
Note: Digital Model Shown

www.elecro.co.uk
1
ENGLISH
Positioning the Unit
CAUTION: To prevent this unit falling into water, do not install above
or alongside your pool.
The Spectrum Hybrid unit is weatherproof but not waterproof; it must be
installed in a dry weatherproof enclosure. The unit must be mounted on a
at vertical surface horizontally or vertically. It must not be submerged in
water or placed in a position where water may collect around the unit.
To prevent the unit inadvertently being dropped into the pool, the unit
must be installed at least 3.5 metres from the edge of the pool.
The unit must always be plumbed into the water system after the lter as
shown in g 3. to prevent dirt and debris being pumped into the unit.
www.elecro.co.uk
FILTER
PUMP ELECRO HEATER
POOL
NON RETURN
VALVE
UV SYSTEM
Fig 3.
POOL
ELECRO
SPECTRUM HYBRID
4
ENGLISH
55W

5
www.elecro.co.uk
ENGLISH
www.elecro.co.uk
FILTER
PUMP ELECRO HEATER
POOL
NON RETURN
VALVE
UV SYSTEM
SPECTRUM
HYBRID
110W
Fig 4.
Mounting the UV Unit
The unit may be mounted on a wall or other suitable vertical surface that
is structurally strong enough (for example: when full of water the unit is
too heavy to mount onto a conventional wooden fence panel). The unit is
supplied with a xing kit. The unit can be mounted vertically as shown in
the next pages in g 5. and 6. or horizontally as shown in g 7.
NOTE!
When mounting the UV it is essential to leave a clearance space of at least 1m
from one side of the unit to allow access to replace the lamp(s) and/or quartz
sleeve(s) when required. Both the lamps and the quartz sleeve can be replaced
from either end of the unit; if installing vertically the 1m clearance space must
be above or below the unit, if installing horizontally the 1m clearance space
must be to the left or right of the unit.

www.elecro.co.uk
1
ENGLISH
WASHER x 4
RAW PLUG x 4
SCREW x 4
Washer x5
Screw x5
Raw plug x5
Fig 5.
6
55W Single Tube Unit

2
www.elecro.co.uk
ENGLISH
RAW PLUG x 5
WASHER x 5
SCREW x 5
Fig 6.
7
110W Double Tube Unit

www.elecro.co.uk
1
ENGLISH
www.elecro.co.uk
Fig 7.
ENGLISHENGLISH
Vertical
mounting
110W Double Tube Unit
Horizontal mounting
55W Single Tube Unit
Vertical
mounting
Horizontal mounting
8
Water must enter low
and exit high
Water must enter low
and exit high
Factory Default
Optional reverse ow
explained on page 10
Factory Default
Optional reverse ow
explained on page 10
Mounting Continued