ElectrIQ eiQ52CANGW User manual

USER MANUAL
BUILT IN COOKER HOOD
eiQ52CANGW/BL eiQ72GWCAN eiQ72GBLCAN
Thank you for choosing electriQ
Please read this user manual before using this
product and keep it safe for future reference.
Visit our page www.electriQ.co.uk for our entire product range

2
CONTENTS
SAFETY
3
UNPACKING
5
PRODUCT OVERVIEW
6
INSTALLATION
7
OPERATION
9
CLEANING AND MAINTENANCE
10
LIGHT BULB REPLACEMENT
10
TROUBLESHOOTING
11
TECHNICAL SPECIFICATIONS
12
SUPPORT
13

3
SAFETY PRECAUTIONS
Whilst this product is compliant with all safety requirements, incorrect or
inappropriate use can lead to both personal injury and potential damage to
property. Please read the contents of this instruction booklet thoroughly before
fitting or using this appliance.
•The cooker hood must be installed in accordance with the installation
instructions and all measurements followed.
•All installation work must be carried out by a competent person or qualified
electrician.
•The unit must be connected to an earthed power supply.
•If venting externally, make sure the ducting has no bends sharper than 90
degrees as this will reduce the efficiency of the cooker hood.
•The cooker hood is for domestic use only and is not designed for commercial
use. It should only be used for the purpose it was intended –to extract vapours
and cooking odours.
•Do not flambé or use an open flame under the cooker hood.
•Do not try to use the cooker hood without the grease filters or if the filters are
excessively greasy. They should be cleaned regularly (see “Maintenance”) or
replaced as necessary.
•The extraction fan must be level to avoid grease collection at one end, as this
could cause a potential fire risk.
•Do not leave frying pans unattended during use because overheated fat or oils
might catch fire.
•If the cooker hood is damaged, do not attempt to use it.
•If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or a similarly qualified person in order to avoid a hazard.
•This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved.
•Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
•Children should be supervised to ensure that they do not play with the
appliance. It is not a toy.
•The plug must be accessible after installation for isolation in case of an
emergency –or an appropriate fused switch if the unit is hard-wired to the
mains via a spur.

4
•The minimum distance between the surface of the hob and the lowest part of
the hood should be at least 65cm. A distance of between 65cm and 75cm gives
peak efficiency.
•The air must not be discharged into a flue that is used for exhausting fumes
from appliances burning gas or other fuels.
•When the hood is vented externally and used with appliances which burn fuel
(e.g. gas, oil, wood) the area must be sufficiently ventilated to ensure safe
operation. Fresh air must be allowed to freely enter the room to prevent a partial
vacuum.
•A partial vacuum can starve the heating appliance of oxygen, impairing
combustion. It can also prevent toxic fumes from leaving the room, or can
cause fumes to be sucked into the room from outside.
•Safe operation is only possible when the partial vacuum within the working area
does not exceed 4 Pa (0.04 mbar). This can be achieved by ensuring air is able
to enter the room from outside through a suitable sized opening which cannot
be sealed during operation. A number of alternative solutions are available to
ensure this. If in any doubt, professional advice should be sought.
•Regulations concerning the discharge of air have to be fulfilled.
•There is a potential fire risk if cleaning is not carried out in accordance with the
instructions.
•Clean your appliance periodically by following the method given in the chapter
MAINTENANCE
•If used in recirculation mode, the charcoal filters trap odours and must be
replaced at least once a year depending on how frequently the cooker hood has
been used.
•For safety reasons, please use only the same size of fixing or mounting screw,
which are recommended in this instruction manual.
•Warning: Failure to install the screws or fixing device in accordance with these
instructions may result in electrical hazards
CAUTION: Accessible parts of the hood can become very hot during
use with cooking appliances, whether in use or not, due to heat rising
from the hob. Sufficient time should be allowed for the unit to cool before
touching either the housing or the grease filters

5
BEFORE USAGE
Before usage, read all the instructions and make sure that the voltage (V) and the frequency
(Hz) indicated on the identification plate (found inside the cooker hood) and all the data inside
the appliance are exactly the same as the voltage and frequency in your home.
Plug the power lead into the power socket (or if connecting directly to the mains via a
switched spur, ensure the work is carried out by a competent, qualified person) and the
cooker hood is then ready for use.
UNPACKING YOUR APPLIANCE
•Please take great care when unpacking; a sharp blade should not be used to open the box,
as it may go deep enough inside to damage components. Components damaged or marked
by careless unpacking are not covered under the guarantee.
•Carefully unpack the contents and check against the section below (Parts) and the next
section (Product overview).
•Packaging materials should be recycled in accordance with local regulations

6
PRODUCT OVERVIEW - PARTS SUPPLIED
DESCRIPTION
ILLUSTRATION
Qty.
Cooker hood
1
Adaptor
1
Cable Tie
1
Air Flap
2

7
INSTALLATION
1. The cooker hood should be placed at a
distance of 65-75cm (26-30inch) from the cooking
surface.
2. Drill a hole of 500*275(mm) for 52CM and 700*275(mm) for model 72CM in
the cabinet.
3. Unscrew the 4 screws on the outer glass frame
panel, pull out the light wire, take down the outer
glass frame panel.

8
4. There are metal sliders at both sides,
connecting with 2 screws per each slider.
Screw out the outer 2 screws on both
sliders, keep these screws safe. Loosen the
inner 2 screws, so that the slider can move
to inside or outside the body.
5. Move the slider inside the hood body, put the hood into
the cabinet. Then move the slider outside the body so that
the hood can be mounted onto the cupboard. Tighten up the
screws on the sliders so that they can be firmly fixed.
6. Connect the light wire and assemble the outer glass frame panel by 4
screws.
7. Install the outlet and expansion pipe: install the outlet on the cooker hood,
then cover the expansion pipe on the outlet and lead it to outdoor.
CARBON FILTER (Available separately)
Activated carbon filters can be used to trap odors, and must be used if the hood is not vented
to the outside. They are available from the same stockist you purchased the hood from under
the following reference: EIQTMCARBONCURV

9
OPERATION
TOUCH CONTROL (T10)
ON/OFF BUTTON
Press to turn the unit ON/ OFF
POWER DOWN BUTTON
When in use, press this button to decrease the power by one level.
DIGITAL DISPLAY
The units current speed will be displayed.
POWER UP BUTTON
When in use, press this button to increase the power one level.
LIGHT BUTTON
Press once to turn the lights on, press again to turn the lights off.
DELAY FUNCTION
When the motor is on, press the light button for 3 seconds to set 5 minutes delay,
the number on the display screen will flash when the delay function is activated.
Press the light button again to cancel the delay, the display screen will not flash
when the delay has been cancelled.

10
MAINTENANCE
Before cleaning, switch the unit off and pull out the plug, or switch off at the relevant mains
switch if the unit has been hard-wired. Make sure the unit has no power being fed to it.
REGULAR CLEANING
Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning
detergent. Never use metal pads, chemicals, abrasive material or a stiff brush to clean the
unit.
NOTE: Do not use a steam-cleaner to clean the hood; electrical components could be
damaged or short-circuit as a result.
LIGHT BULB REPLACEMENT
1. Unscrew the 4screws on the outer glass frame.
2. Pull out the light wire and take down the outer glass frame.
3. Unscrew the screws on the light bracket and replace the light.
4. Connect the light wire and assemble the outer glass from panel in the reverse order of the
previous steps.
LIGHT SPECIFICATIONS
MAX WATTAGE
2W
LED MODULES
Rectangle LED Lamp
VOLTAGE RANGE
DC 12 V

11
TROUBLESHOOTING
Fault
Cause
Solution
Light on, but fan
does not work
The fan blade is jammed.
Switch off the unit. Repair to be carried out by
qualified service personnel only.
The motor is damaged.
Both light
and fan do not
work
Halogen light bulb blown
Replace the bulb with correct rating.
Power cord loose
Plug in to the power supply again.
Excessive
Vibration
The fan blade is
damaged.
Switch off the unit. Repair to be carried out by
qualified service personnel only.
The fan motor is not fixed
tightly.
Switch off the unit. Repair to be carried out by
qualified service personnel only.
The unit is not hung
properly on the bracket.
Take down the unit and check whether the
bracket is in proper location.
Suction
performance
not good
1 Grease filters
clogged?
2 Distance between
the unit and the cooking
plane too great.
1 Clean or replace grease filters. 2 Adjust
the distance to between 70cm and 80cm.

12
SPECIFICATION
Symbol
Value
Unit
Annual Energy
Consumption
AEChood
47.29
kWh/a
Time increase factor
f
1.28
Fluid Dynamic Efficiency
FDEhood
20.01
Energy Efficiency Index
EEIhood
67.79
Measured airflow rate at
the best efficiency
QBEP
240.89
m3/h
Measured air pressure at
best efficiency point
PBEP
284.16
Pa
Maximum airflow
Qmax
455.58
m3/h
Measured electric power
input at best efficiency
point
WBEP
95
W
Nominal power of the
lighting system
WL
4
W
Average illumination of the
lighting system on the
cooking surface
Emiddle
114.4
lux
Measured power
consumption on standby
mode
PS
/
W
Measured power
consumption on off mode
PO
0.417
W
Sound power level
LWA
70
dB

13
INFORMATION FOR DISMANTLING
Do not dismantle the appliance in a way which is not shown in the user manual. The
appliance could not be dismantled by user. At the end of life, the appliance should not be
disposed of with household waste. Check with your Local Authority or retailer for recycling
advice.
INFORMATION FOR DISMANTLING
Do not dismantle the appliance in any way which is not shown in the user manual. The
appliance must not be dismantled by an unqualified person. At the end of its life, the
appliance should not be disposed of with general household waste. Check with your Local
Authority or retainer for recycling advice.
electriQ UK SUPPORT
www.electriQ.co.uk/support
Call: 0871 984 4416
Office hours: 9AM - 5PM Monday to Friday
www.electriQ.co.uk
Unit J6, Lowfields Business Park
Lowfields Way, Elland
West Yorkshire, HX5 9DA
Recycling facilities are now available for all customers at which you
can deposit your old electrical products. Customers will be able to
take any old electrical equipment to participating sites run by their
local councils. Please remember that this equipment will be further
handled during the recycling process, so please be considerate
when depositing your equipment. Please contact the local council
for details of your local household waste recycling centers.