Electro-Voice N868 User manual

The N/D868 is truly a top performer in any application.
Whether in a live sound or studio environment, the
N/D868 is able to handle incredibly high sound pressure
levels without distortion or overriding the input mixer.
With a response specifically designed to kick the
N/D868 can be used as is - no additional EQ required.
Electrovoice was the first to utilize the neodymium
magnet structure, and it remains at the heart of our new
N/DYM series of microphones. Experience the leader
again for the first time and hear the difference.
 Designed specifically for kick drum applications in
live or studio environments
 Optimized sensitivity for the high sound pressure
levels found in bass drum micing
 Extended low-frequency response

No additional EQ required

Rugged steel construction for exceptional durability
Operation
The low frequency response of the N/D868 microphone
varies with the distance from the sound source. Known as
proximity effect, maximum bass response is produced
in close-up use with the microphone ¼ inch from the
sound source. Normal bass response is experienced with
working distances greater than 24 inches. Working close
to the microphone will produce a more robust sound.
Close up positioning of the microphone will also reduce
the potential for feedback from the sound reinforcement
system. When , the bass-boost provides an increase in
overall microphone output level. The mixer gain may be
proportionately reduced, resulting in a reduction of the
systems sensitivity to feedback caused by sound entering
the microphone from the loudspeakers.
Microphone Use and Placement
Please note that micing techniques are a matter of personal
preference. These are merely guidelines to assist in the
placement of the microphone to gain optimal performance.
Usage Optimal Placement
Kick Drum Remove drum head and damp
with a pillow or blanket.
Position the mic on the pillow
or blanket a few inches in
front of the drum beater. As
an alternative, position the
mic on a small boom stand
with the mic extended into the
drum and at a 90° angel to the
drum beater.
Standard Placement & Use Guidelines
1. Always point the microphone at the desired source of
sound, and away from any unwanted sources.
2.
The microphone should be located close to the
sound source to minimize interference from other
potential sound sources.
3.
Use the 3-to-1 rule when using multiple
microphones. Place each microphone three times
farther from other microphones as from the desired
sound source.
4. Minimize over-handling of the microphone to reduce
unwanted mechanical noise
5. Working close to the microphone will increase the
bass tone and also provide increased
gain-before-feedback.
N/D868 User Manual
WIRED
MICROPHONE

Warranty
This product is guaranteed against malfunction from
any cause for two (2) years from the date of original
purchase. In addition, the Limited Warranty for the
acoustic system contained in the microphone shall
apply for the life of this product, defines as a period of
ten (10) years from the date that the manufacture of this
microphone model has been discontinued. Any and all
active electronics incorporated in this microphone are
guaranteed against malfunction due to material
workmanship for a period of three (3) years from the
date of original purchase. This Limited Warranty does
not extend to cables, connectors, or switches.
For warranty service please call us at:
616-695-6831 or
1-800-234-6831
N/D 868 Specifications
Frequency Response: ..............20-10,000 Hz
Polar Pattern: ..................Cardioid variant
Impedance: ...........150ohms balanced (low-Z)
Sensitivity:
Open Circuit Voltage:......1mV/Pascal @ 1 kHz
Power Level:(0 dB=1mW/pascal) -51.7 dB @1 kHz
Microphone Connector ..........3-pin, XLR-type
Equivalent Output Noise ........17dBAweighted
(0 dB= 0.00002 pascal)
Polarity: .....Positive pressure on diaphragm causes
positive voltage on pin 2 ref. pin 3
Materials:
Grille screen ....................Memraflex ä
Finish: ..................Non-reflecting black
Case: ................................Steel
Dimensions:
Length.................@5.22 in. (132.6 mm)
Diameter ..................@2.36 in. (60 mm)
Shank....................@1.0in.(25.4 mm)
Weight:
Net....................@10.4 oz (295 grams)
Shipping ...............@26.5 oz (750 grams)
Accessories included:
320 stand clamp
Soft zippered gig bag
AVERAGE RESPONSE
N/D868 response
90
60
30
120
150
180
210
240
270
300
330
0
N/D868 polar
5 dB per division
Part Number 535836
USA 9600AldrichAve.S., Minneapolis, MN 55420,Phone:[phone],FAX:[phone]
Canada 705ProgressAvenue,Unit10, Scarborough,Ontario,Canada,M1H2X1,Phone:[phone],FAX:[phone]
Switzerland Keltenstrasse11,CH-2563IPSACH,Switzerland,Phone:[phone],FAX:[phone]
Germany HirschbergerRing 45, D94302,Straubing,Germany, Phone:[phone],FAX:[phone]
France Parcde Courcerin,AlleeLech Walesa, Lognes,f-77185Marne La Vallee, France,Phone:[phone],FAX:[phone]
Australia Unit23, SloughBusinessEstate,SilverwaterN.S.W. 2128,Australia,Phone:[phone],FAX:[phone]
HongKong UnitE &F, 21/F, Luk Hop IndustrialBldg., 8 Luk Hop St.,SanPoKong, Kowloon,HongKong, Phone:[phone],FAX:[phone]
Japan 2-5-60Izumi, Suginami-ku,Tokyo,Japan 168,Phone:[phone],FAX:[phone]
Singapore Telex Comm Pre Ltd,3015AUbi Rd 1, #0510,Kampong Ubi IndustrialEstate, Singapore 408705,Phone:[phone],FAX:[phone]
Mexico TecnologiaEspecializadaEDD S.A. deC.V., Av. ParqueChapultepec#66-201,ElP arque,Naucalpan,Mexico,DF 53390,Phone:[phone],FAX:[phone]