Electrolux BETA EA 340 S1 BA User manual

Q&CI - Technical Support 0 XXX XX XX –XX Rev. XX
© ELECTROLUX HOME PRODUCTS
Consumer Service - EMEA
Quality & Continuous Improvement - Technical Support
SERVICE MANUAL
COOKING
FOR INTERNAL AND PARTNERS USE ONLY
For internal and partners use only.
RANGE HOOD
BETA
EN
Publication number
599 818 562
Edition: 05/2018 - Rev. 00

Q&CI - Technical Support 1 599 818 562 Rev. 00
CONTENTS
CONTENTS 1
1PURPOSE OF THIS MANUAL 2
2SAFETY ERROR! BOOKMARK NOT DEFINED.
3BETA RANGE HOOD 4
4ACCESSIBILITY 5
5CIRCUIT 15
6TROUBLE SHOOTING 18

Q&CI - Technical Support 2 599 818 562 Rev. 00
1 PURPOSE OF THIS MANUAL
The purpose of this Service Manual (SM) is to provide Service Engineers who are already familiar with the repair procedures of Hoods
This SM will provide information on:
oHood Range
oAccessesbility
oTechnical and functional characteristics
oTrouble shooter
Document Revisions
Rev.
Date
Description
Author
00
05/2018
Document creation
Said Hatem
Acronyms and Abbreviations
Terms
Initialism
Grease Filter Assembly
GFA
Blower Assembly
BA
Candle Lamp
CL
Spot Lamp
SL
Light Diffuser
LD
Feeder Cable
FC
Control Assembly
CA
Led Driver
LD*
Carbon Filter Holder
CFH

Q&CI - Technical Support 3 599 818 562 Rev. 00
2 SAFETY
All the work to be performed inside the appliance requires specific skills and knowledge and may only be carried out by
qualified and authorised Service Engineers
Before you access internal components, take the plug out of the socket to disconnect the power supply.
Some of the components in the mechanical part could cause injuries, so wear suitable protection and proceed with
caution.
Prior to touching the light bulbs ensure they are cooled down.

Q&CI - Technical Support 4 599 818 562 Rev. 00
3 BETA RANGE HOOD
3.1 Hood Features
Variant 1
1b
Control Assembly Rocker Button
2b
Light Diffuser & Candle Lamp
Variant 2
1a
Control Assembly Push Button
2a
Spot Lamp
3
Grease Filter
4
Blower Assembly
5
Ducts

Q&CI - Technical Support 5 599 818 562 Rev. 00
4 ACCESSIBILITY
4.1 Grease Filter Assembly (GFA)
1. Slide the latch in the handle structure backwards to unsnap Grease
Filter.
2. Release the Grease Filter from the slots in the left side of its frame.
Perform the same steps to remove the other filters.
Placing back the Grease Filter: Start with the step 2 placing the guide
projections in the
guide and snap the handle latch
4.2 Light Diffuser (LD)
Perform chapter 4.1
!Have work gloves to avoid the cuts when you unsnap
1. Unsnap two from the four snaps of the light diffuser inside the
hood.
2. Push the light diffuser down to remove it.

Q&CI - Technical Support 6 599 818 562 Rev. 00
4.3 Lamp
4.3
Lamp
Picture
Procedure to access
4..3.1
Candle Lamp
See subchapter 4.3.1
4.3.2
Spot Lamp
See subchapter 4.3.2

Q&CI - Technical Support 7 599 818 562 Rev. 00
4.3.1 Candle Lamp (CL)
Perform chapter 4.2
!Unplug the power cable from the power socket
!Prior to touching the light bulbs ensure they are cooled down
1. Turn the bulb in anti- clockwise direction to take it out and
in clockwise direction to place it back.
4.3.2 Spot Lamp (SL)
Perform chapter 4.1
!Have work gloves to avoid the cuts when you unsnap
1. Remove the cables from the hooks.
2. Unsnap the lamps.
3. Unsnap the connectors.

Q&CI - Technical Support 8 599 818 562 Rev. 00
4.4 Ducts
!Have work gloves to avoid the cuts.
1. Unfasten the 2* screws which secure the ducts to the wall bracket.
2. Slide down the upper duct into the below one.
3. Lift both and take the duct out
4.5 Carbon Filter Holder (CFH)
Perform chapter 4.1
1. Unfasten the 1* screw which secure the CFH to the hood
shell.
2. Pull down towards left to extract from the lateral slots.

Q&CI - Technical Support 9 599 818 562 Rev. 00
4.6 Blower Assembly (BA)
Perform chapter 4.1 and chapter 4.5
!Unplug the power cable from the power socket
! Be sure to hold up the BA during the perform of the 3rd step of this chapter
1. Depress the two snaps on the power connector inward and pull to
separate out.
2. Turn the nut anti clockwise direction to remove the ground cable and
clockwise direction to place it.
3. Unfasten the two screws which secure the BA to the hood shell.
4. Pull down the BA.
BETA EA 340 S1 BA MOTOR
POWER(W)
BETA EA 340 S1 PU MOTOR
POWER(W)
BETA EB 25 MOTOR
POWER(W)
POWER
MAX Speed
115
100
205
2nd Speed
_
70
170
MIN Speed
65
60
125
Label