Eling MLS052 User manual

MLS052 Instructions
1.
Speedometer
LCD display, speed up 5%, 18Hz = 63KM/H; maximum display
199KM/H.
2.
Tachometer
166Hz to 10 *1000r/min. When the speed exceeds 4 *1000r/min, the
alarm light flashes. When the speed exceeds 5 *1000r/min, the alarm
lamp will be on for a long time. The maximum display is 12 x
1000r/min.
3.
Fuel gauge
E point 98, F point 8. The fuel meter with resistance greater than 85
flashes and the alarm lamp flashes.
4.
Water temperature meter
When the resistance of the water temperature sensor is lower than
165, the water temperature alarm lamp will be on for a long time.
5.
Key function
A. Short press the button, total, subtotal A, subtotal B switch.
B. Press the button for 4 seconds to switch between metric and British system. The
default is metric system. After the change, it can be saved even if the power is
completely cut off.
C. In subtotal A interface, press the key for 3 seconds, subtotal A clears.
D. In subtotal B interface, press the key for 3 seconds, subtotal B clears.
6.
Clock adjustment
If the upper and lower keys are pressed at the same time, it enters the
clock adjustment. Short key presses change the time.
7.
Backlight
LCD backlight: white.
8.
From the cable side
①
②
③
④
⑤
⑥
⑦
⑧
⑨
Terminal
DJ611-2.8*0.5
①Red: Connect to a constant 12V positive feed or
directly to battery positive (for settings memory)
②Red and black: Rev counter signal
③Light blue: Connect to right turn signal positive
(shows a green light)
④Green: Connect to Battery negative or earth
⑤Green and white: water temperature signal
⑥Blue: Connect to high beam signal positive (shows a
light blue light)
⑦Black: Connect to ignition switch 12V positive output
(to switch unit off and on)
⑧Blue/White: Fuel level signal
⑨Orange: Connect to left turn signal positive (shows a
green light)

9.
From the cable
side
N
⑤
④
①
②
③
Green/Red: N gear
Pink: 1 gear
Blue/Red: 2 gear
Green/Black: 3 gear
Yellow/Red: 4 gear
Yellow/White: 5 gear
10.
4 round head
Gray: 6 gear, negative control, LCD display
Brown red: engine fault light, negative control, yellow
light
11.
③
②
①
①Black/white: sensor signal
②Green: sensor negative
③Red/white: sensor positive
Background parameter settings
Press and hold the top “sel” key, then turn on the ignition switch. After 5 seconds, it will enter the settings, divided into six pages.
Page 1: Setting of tyre circumference
C-1850 means the default tyre circumference is 1850 mm. Short presses of the top “sel”button changes each digit. Press the bottom “set”
button to move to the next digit. The circumference can be set from 500 to 2600 mm. Press the top “sel”key for 3 seconds to save the
circumference and enter the next page.
Page 2: Magnets Number Setting
C – 02 means there are two magnets, 1 - 12 can be set. Short presses of the top “sel”button changes each digit.
Press the top “sel”key for 3 seconds to save the number of magnets and enter the next page.
Page 3: Speed setting interface
C-2, 2 indicates that the engine is 2 cylinders. (166HZ) Switch 2/4 cylinders by pressing the top “sel”key. Press the button for 3 seconds to save
it into the two-wire and three-wire fuel setting interface. ,
Page 4: Fuel setting of two lines and three lines (two lines and three lines should be set in the general term of upper computer)
The 188 first 8-word speed display shows 4, the total cumulative display E-3, 3 for the three-line oil meter, 3 for the three-line display E-3, 2 for
the two-line display E-2, and 3/2 for the switch by pressing the button. Press the button for 3 seconds to save and enter the accumulated clearing
interface.
Page 5: Changing the speed between mph and kmh
Short presses of the top “sel”button changes between mph and kph.
Press the top “sel”key for 3 seconds to save the speed setting and enter the next page.
Page 6: Resetting the total mileage.
The total mileage can be reset to zero in this page.