Elived YD1007 User manual

100LBS
45.5KG
Max:
Max:600x400mm/24x16"
Min:75x75mm /3x3"
42"~70"
(A0)
If you have any questions, please contact us via [email protected]
YD1007 INSTALLATION INSTRUCTION
Velcro cable ties X5 Bubble level X1
- 1 -

Hammer
3/8"(10mm)
Masonry Drill Bit
7/32"(5.5mm)
Wood Drill Bit
AwlStud Finder
Socket Wrench
1/2"(13mm)
ElectrodrillScrewdriverPencil
3 What is your wall
made of?
Solid concrete
wall?
●This product is designed for use in wood stud or solid concrete wall.
- DO NOT install into drywall alone.
●The wall must be capable of supporting five times the weight of the TV and mount
combined.
●Do not apply this product to any purpose not indicated by ELIVED.
●Incorrect installation may result in product damage or body injury. ELIVED shall
bear no responsibility for any damage or injury resulted from incorrect installation,
incorrect assembly or misuse.
Please read this instruction carefully before installation.
If you do not understand these instructions or have doubts about the safety of the
installation, assembly or use of this product, contact CUSTOMER SERVICE via
[email protected]
5 Safety Caution
2M2M
Band Tape
Drywall with
wood studs?
CAUTION:
Yes --- Perfect!
No --- This mount is NOT compatible.
MAX:
400mm/16"
MAX:600mm/24"
Yes --- Perfect!
No --- This mount is NOT compatible.
4 Installation Tools
(Not Included)
2Does your TV
(including accessories)
weigh less than
100 LBS (45.5 KG)?
1Is your TV VESA
equal to/greater than
75x75mm/3x3" and
equal to/less than
600x400mm/24x16"?
Before getting started, let’s make sure this mount is perfect for you!
100LBS
45.5KG
Max:
DO NOT install
into drywall alone
Perfect! Perfect!
Wood Stud Install
Concrete Install
- 2 -

Wall Plate Bracket
Allen Key
Hardware Included
01 x2
02 x2
03 x1
Hardware （Wall /Product) Wall Plate Kit
5/16 x 2½ in
Lag Bolts
x4 x1
C
x4
D
x4
EA
Washers
Ø8mm
Bolts
M5 x 12
Nuts
M5
x4
B
Open end Wrench
Philips Screws
M6 x 15mm
M6 x 30mm
Philips Screws
M4 x 12mm
M4 x 30mm
Washers
Ø6mm
M4-5-6
Spacers
L10mm
x4
x4 x4x4
Philips Screws
M8 x 25mm
M8 x 45mm
x4
x4 x8 x4
Spacers
L5mm
x8
TV Screws / Washers
M-A M-B M-C M-D M-E M-F
- 3 -

M6M4 M8
Correct Correct
Too Long
Too Short
- 4 -
Select TV Screw Diameter
Thread screws by hand into the threaded holes on the back of your TV to select which screw
diameter fits your TV.
Attach Brackets to TVSTEP 1
1-1
Select TV Screw Length1-2

- 5 -
Attach the Brackets
Position your brackets over your TV hole pattern - making sure the brackets are centered
and level over the TV hole pattern.
Secure thebrackets using your screw/washer/spacer selection:
(a) For Flat Back
(b) For Round Back / Extra Space
CAUTION: Ensure bracket is securely fastened before moving on to the next step.
02
02
M-A
M-B
M-C
Use the longer
screws
M-E
M-A
M-B
M-C
Use the shorter
screws
M-E
M-D
M-F
(a) Flat Back
(b) Round Back /
Extra Space
1-3
No need to use
for M8 screws
No need to use
for M8 screws
TOP OF TV
TOP OF TV

STEP 3A Wall Plate Installation (Wood Stud)
3A-1
Locate your studs. Verify and mark
the center of the studs by finding
the stud edges using an awl, a thin
nail, or an edge-to-edge stud finder,
then measure the space of the
studs and record.
16in to 24in
3A-2
- 6 -
Position the wall plate assembly
at your desired height and line
up the holes with your stud
center line. Level the wall plate
assembly and mark the pilot
hole locations.
01
Assemble the wall plates [01] together with the Bolts [D] x4
and Nuts [E] x4.
C
E
D
E
D
Assemble Wall PlateSTEP 2
!
01
01
01
Secure 2 bolts and nuts at the
back of the wall plate assembly.
Back
CAUTION!

3A-3
Drill pilot holes using a 7/32 in. (5.5 mm)
diameter drill bit.
Drill Pilot Holes
X
X
X
X
7/32 in.
Ø5.5 mm
in. (70 mm)
Mount wall plate using 4 sets of
5/16” lag bolts (a) and washers
B with a 1/2” socket wrench (not
included).
B
A
- 7 -
01
3A-4
2
B
A

STEP 3B Wall Plate Installation (Concrete or Brick)
3B-1 Position the wall plate assembly
at your desired height , level the
wall plate assembly and mark
the pilot hole locations.
Drill pilot holes
3B-2
3B-3
2.75in 70 mm
Ø 10 mm
Ø 10 mm
01 AB
01
Install wall plate using lag bolts , washer and anchor (not included).
Tighten the lag bolts until they are pulled firmly against the wall plate .
A
- 8 -
01
01 Concrete Wall
Contact us by email [email protected] to have
these additional pieces shipped directly to you.
Concrete Wall Anchor 4pcs
Concrete wall anchor (NOT INCLUDED)
Concrete Wall
A B

STEP 5 Attach TV to Wall Plate Assembly
Install wall plate using lag bolts , washer and anchor (not included).
Tighten the lag bolts until they are pulled firmly against the wall plate .
- 9 -
Adjust the tilting angle with the Allen Wrench
STEP 4 Adjust the Tilting Angle
C
C
Tighten
Adjust
the nuts
Loosen
C

- 10 -
STEP 6 Secure Brackets to Wall Plate Assembly
02
Pull the strap down and push the TV to secure the TV brackets to the wall
plate assembly.
Squeeze and
hold control to
adjust cord
length
Attach
pendant to
wall plate
with magnet.
02
02

- 11 -
03
Watch the
level during
adjusting.
OPTION: Adjust the Bolts on the Brackets to Level the TV
Horizontal line
If the TV is not level after installing, please find the bracket on the lower side and turn
the bolt clockwise on the bracket to level the TV by using the Allen key 03 .
03
Turn the bolt clockwise on the lower bracket
to level the TV by using the Allen key .
03

Product Dimensions:
- 12 -
425mm / 16.73”
49mm / 1.93”
150mm / 5.91in
MAX 600mm / 23.62”
401.6mm / 16”
662.4mm / 26.08”
610mm / 24”
457mm / 18”
MAX 400mm / 15.75”
+5° ~ -12°
13.2mm / 0.52”
Post installation
level adjustment