Elived YD1007 User manual

Thread screws by hand into the threaded holes on the back of your TV to select which screw
diameter fits your TV.
When attaching brackets to the flat screen, be careful not to over tighten screws and
be sure that screws do not bottom out in the mounting holes.
M6M4 M8
Wall Plate Bracket
Allen Key
Hardware Included
01 x2
02 x2
03 x1
Hardware （Wall /Product) Wall Plate Kit
5/16 x 2½ in
Lag Bolts
x4 x1
C
x4
D
x4
EA
Washers
Ø8mm
Bolts
M5 x 12
Nuts
M5
x4
B
Correct Correct
Too Long
Too Short
Open-end Wrench
Step 3A Wall Plate installation (wood stud)
3A-1
Locate your studs. Verify and mark
the center of the studs by finding
the stud edges using an awl, a thin
nail, or an edge-to-edge stud finder,
then measure the space of the
studs and record.
Philips Screws
M6 x 15mm
M6 x 30mm
Philips Screws
M4 x 12mm
M4 x 30mm
Washers
Ø6mm
M4-5-6
Spacers
L10mm
x4
x4 x4x4
Philips Screws
M8 x 25mm
M8 x 45mm
x4
x4 x8 x4
Spacers
L5mm
x8
TV Screws / Washers
M-A M-B M-C M-D M-E M-F
16in to 24in
02
02
M-A
M-B
M-C
Use the longer
screws
M-E
M-A
M-B
M-C
Use the shorter
screws
No need to use
for M8 screws
M-E
M-D
M-F
Assemble the wall plates [01] together with the Bolts [D] x4
and Nuts [E] x4.
C
E
D
E
D
Assemble wall plateStep 2
!
01
01
01
Secure 2 bolts and nuts at the
back of the wall plate assembly.
Back
CAUTION!
No need to use
for M8 screws
TOP OF TV
TOP OF TV
(V2.1)
If you have any questions, please contact us.
YD1007
INSTALLATION INSTRUCTION
Max:600x400mm/24x16"
Min:75x75mm /3x3"
42"~70"
(a) For Flat Back
(b) For Round Back / Extra Space
Bubble level X1
Max:
(45.5KG)
100LBS
Safety Caution
Must Check Before Getting Started
Installation Tools (Not Included)
Band
Tape
2M
Socket
Wrench
ScrewdriverPencil Electrodrill
Stud
Finder
HammerAwl Wood
Drill Bit
Masonry
Drill Bit
Wood Stud Installation Concrete Installation
1/2"
(13mm)
3/8"
(10mm)
7/32"
(5.5mm)
Step 1-2 Select TV screw length
Step 1-1 Select TV screw diameter Step 1-3
Attach the bracket
No!
No!
Please read this instruction carefully before installation.
If you do not understand these instructions or have doubts about the safety of the installation, assembly
or use of this product, please contact us.
●This product is designed for use in wood stud and solid concrete wall.
- DO NOT install into drywall alone.
●The wall must be capable of supporting five times the weight of the TV and mount combined.
● Do not apply this product to any purpose not indicated by ELIVED.
● Incorrect installation may result in product damage or body injury. ELIVED shall bear no responsibility
for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage,
please contact us.
MAX:600mm/24"
MAX:
400mm/16"
Max:
(45.5KG)
100LBS
Min. 8"
Min. Wood Stud Size:
nominal 2”(51mm) actual 1 1/2”(38mm)
Min. Wood Stud Size:
nominal 4”(102mm) actual 3 1/2”(89mm)
(203mm)
Solid concrete wall
CAUTION: DO NOT install into drywall alone.
<16mm(5/8")
Drywall with wood studs
24"(610mm)
2
1
5
4
3

Attach
pendant to
wall plate
with magnet.
01
Step 3B Wall plate installation (concrete or brick)
3A-3
Drill pilot holes using a 7/32 in. (5.5 mm)
diameter drill bit.
3B-1 Position the wall plate assembly
at your desired height , level the
wall plate assembly and mark
the pilot hole locations.
Drill pilot holes
3B-2
3B-3
Contact us to have these
additional pieces shipped directly
to you.
Concrete wall anchor 4pcs (NOT INCLUDED)
3A-2
X
X
X
X
7/32 in
Ø5.5 mm
2.75in (70 mm)
Mount wall plate using 4 sets
of 5/16” lag bolts (a) and
washers B with a 1/2”
socket wrench (not included).
B
A
Position the wall plate assembly
at your desired height and line
up the holes with your stud
center line. Level the wall plate
assembly and mark the pilot
hole locations.
01
01
3A-4
2
B
A
Bubble Level
01
AB
Option: Adjust the bolts on the brackets to level the TV
02
Pull the strap down and push the TV to secure the TV brackets to the wall plate assembly.
02
02
Squeeze and hold
control to adjust
cord length
Horizontal line
Maximum leveling
adjustment 0.5”
Turn the bolt clockwise on the
lower bracket to level the TV
by using the Allen key .
03
If the TV is not level after installing, please find the bracket on the lower side and turn
the bolt clockwise on the bracket to level the TV by using the Allen key 03.
03
Step 5 Attach TV to wall plate sssembly
Product dimensions:
Bubble Level
Step 5 Secure brackets to wall plate assembly
Adjust the tilting angle with the open-end wrench .
Step 4 Adjust the tilting angle
C
C
Tighten
Adjust
the nuts
Loosen
C
Watch the
level during
adjusting.
03
49mm / 1.9”
150mm / 5.9”
Max 600mm / 23.6”
406mm / 16”
663mm / 26”
610mm / 24”
457mm / 18”
Max 400mm / 15.8”
+5° ~ -12°
13.2mm / 0.52”
Post installation
level adjustment
2.75in (70 mm）
Ø 10 mm
Ø 10 mm
3/8in
No!
No!
01 A
B
01
Install wall plate using lag bolts ,
washers and anchors (not included)
with Socket Wrench, NO Electrodrill..
Tighten the lag bolts until they are
pulled firmly against the wall plate .
A
Ø10*61mm
7
6
8
11
10
9