Elkay SWIRLFLO FLEXI-GUARD ezH2O EZWS-EDFPBM117K Instructions for use

2000000495 (Rev. A - 01/22)
EDFPBM117WS EDFPBM117WS-F
Page 1
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
When installation is complete, ensure these instructions are left in the plastic bag
provided inside the installed unit for future reference.
Service to be performed by authorized service personnel only.
INSTALLER
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices
to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which
results in an “electrolysis” effect occurring in the fountain. This may result in water which has a
metallic taste to it or has a noticeable increase in the metallic content of the water.
When inspecting plumbing circuit, remember the line may be grounded some distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.
Any drain ttings provided by the installer should be made of plastic which will electronically isolate
the fountain from the remainder of the building’s plumbing circuits.
LZWS-EDFPBM117KEZWS-EDFPBM117K
SWIRLFLO®Fountains with FLEXI-GUARD®
and ezH2O® Bottle Filler
INSTALLATION & USE MANUAL

2000000495 (Rev. A - 01/22)
EDFPBM117WS EDFPBM117WS-F
Page 2
**NEW INSTALLATIONS MUST USE GROUND FAULT CIRCUIT INTERRUPTER *GFCI)
Figure 1 - Rough-in Dimensions
38-1/2"
(978mm) 18-3/8"
(467mm)
5/8"
(16mm)
1-5/8"
(41mm)
1-5/8"
(41mm)
OPTIONAL ACCESS PANEL
(ACCESS PANEL REQUIRED FOR INSTALLATION WITH
NO REAR
ACTIVATION SENSOR
ACCESS)
BOTTLER FILLER DRAIN (TRAP REQUIRED SUPPLIED BY INSTALLER)
8" (203mm) MINIMUM CLEARANCE REQUIRED FOR DRAIN CONNECTION AND ACCESS TO BOTTLE FILLER ELECTRICALS
9-7/8"
(251mm)
34-11/16"
(881mm)
44"
(1119mm)
37-3/8"
(949mm)
38-1/2"
(978mm)
36-1/2"
28-3/4"
(730mm)
(927mm)
21-1/2"
(546mm)
16-1/2"
(419mm)
41-11/16"
(1058mm)
33-15/16"
(862mm)
1-1/2" IPS
WASTE LINE
3/8" IPS
SUPPLY
27"
(686mm)
ADA
REQUIREMENT
OPTIONAL ACCESS PANEL
(ACCESS PANEL REQUIRED
FOR INSTALLATIONS WITH
NO REAR ACCESS)
FINISHED FLOOR
18-11/16"
(475mm)
JUNCTION BOX LOCATION

2000000495 (Rev. A - 01/22)
EDFPBM117WS EDFPBM117WS-F
Page 3
12
TO BUBBLER
12
12
12
14
24
TO BUBBLER
13
TO BOTTLE
FILLER
25
31
Figure 3 - LZWS-EDFPBM117K Tube Routing
REQUIRED TOOLS AND MATERIALS
These tables show special tools and/or additional materials
(not provided) which are necessary to complete installation
of these units:
Figure 2 - EZWS-EDFPBM117K Tube Routing
TO BUBBLER
21
FILTER
ASSEMBLY
13
12
12
WATER
INLET
Special Tools
Item Description Quantity
NONE
Additional Materials Not Included
Item Description Quantity
Unplated copper inlet pipe
Service Stop/Shut-off Valve
90° 1-1/4” Drain Line
1-1/4” Tee Drain Line
1
2
3
4
1
1
1
1
TO BUBBLER
31 24
TO BOTTLE
FILLER
1. Make water supply connections (Fig. 11). Install a shut-off
valve and union connection to building water supply (valve
and union not provided). Turn on water supply and ush
the line thoroughly.
Caution: DO NOT SOLDER tubes inserted into the
strainer or lter head as damage to the o-rings may result.
2. Install mounting frame (instructions supplied with mounting
frame.
3. (For LZWS-EDFPBM117K) Install the lter head to the bracket,
then install lter bracket on mounting frame (Fig. 10), plumb from
the lter outlet to the chiller inlet with ¼” elbow, poly tubing and
¼ x ¼ union, install lter.
3a. (For EZWS-EDFPBM117K) Install strainer on the input tube to
the chiller (Fig. 2).
4. Install ¼ x ¼ x 3/8 Tee on building water supply tube. Install
supplied 4” poly tubing and armaex to the outlet of the prev-
ously installed tee. Connect supplied ¼ x ¼ x ¼ tee to the 4” poly
tubing. With the back panel standing close to the frame, connect
3/8” poly tube to the bottle ller.
5. Hang main panel on mounting frame hanger. Make sure the
power cord, reset switch wire & poly tube do not get pinched
between the panel & mounting frame. Ensure the panel engages
at the top. Align fountain holes with mounting frame holes.
6. Remove protective coating from main panel.
7. Install reset switch for bottle ller (Fig. 5). Snap the switch into
position after locating wires through slot. Wrap up the excess
cord.
12

2000000495 (Rev. A - 01/22)
EDFPBM117WS EDFPBM117WS-F
Page 4
NOTE:
When installing replacement bubbler and pedestal, tighten
locknut only to hold parts snug in position. Do Not overtighten.
Figure 6 - Bubbler Details
Figure 4 - Upper Panel Installation
Figure 5 - Fountain Installation
15 Reset Switch
22
27, 28, 29, 30, 31
19
23
23
View From Rear
5
Basin
1
Locknut
22
17
8. Install fountains with (8) 5/16-18 HHMS & (8) 5/16-18 nuts
(provided) (Fig. 5). Connect the ¼” water lines from each
fountain to the remaining openings on the tee at the remote
chiller (cut lines to t as needed).
9. Attach waste tubes (1-1/4” O.D.) to 1-1/4” O.D. slip trap.
Trap on the bottle ller side must be 1-1/2” O.D. (provided by
others).
10. Make nal water supply connections.
11. These products are designed to operate on 20-105 PSI
supply line pressure. If inlet pressure is above 105 PSI, a
pressure regulator must be installed in the supply line.
Caution: Any damage caused by connecting these products
to a supply line with pressure lower than 20 PSI or higher
than 105 PSI IS NOT covered under warranty.
12. Make electrical connections to the bottle ller and remote
chiller. The LCD Bottle counter should illuminate.
13. Verify proper dispensing from the bottle ller by placing a cup,
hand or any opaque object in front of sensor area and verify
water dispenses. Note: the rst initial dispenses might have air
in the line which may cause a sputter. This will be eliminated
once all air is purged from the line. A steady stream of water
assures all air is removed. The sensor has a 20 second maxi
mum ON time. It may be necessary to step away from the
beam a few times to purge all air. Check for leaks.
14. Check stream height from bubbler. Stream height is factory set
for 35 PSI supply. If supply pressure varies greatly from this,
remove push button (Item 7 - Fig. 9) and adjust the screw
on the regulator (Item 8 - Fig. 9). To remove push button,
remove setscrew from bottom of sleeve (Item 6). Insert a small
punch in screw hole and push up while grasping the push but
ton and pull forward removing the push button. Clockwise
adjustment will raise stream height and counterclockwise
movement will lower stream height. For best adjustment
stream should hit basin approximately 6-1/2” from the bubbler.
Reassemble the push button by pushing in on button until the
push button catches in the sleeve. Reinstall the setscrew (Item
20) in the sleeve (Item 6).
15. Install the cover plates.
16. Install the bottom panel, tighten screws (Fig. 4).
17. Optional: Mount optional panels. Slide tongue of panel under
edge of already installed panel. Tighten screws.
Back
Panel
16
16

2000000495 (Rev. A - 01/22)
EDFPBM117WS EDFPBM117WS-F
Page 5
Figure 8 - Fountain Body Assembly
Figure 9 - Push Button Assembly
6
7
8
20
21
11
See Fig. 6
2
9
See Fig. 6
3
12
18
4
10
8
5
21
Figure 7
2
1
3/8”
Wa
ter
Inlet
Filter Head
Assembly
used after 01/01/2021
WATERSENTRY®PLUS FILTER PARTS LIST
(See Fig. 7)
ITEM
NO. PART NO. DESCRIPTION
1
2
51300C
51469C
Filter Assy-3000 Gal.
Assy-Filter & Brkt includes Fltr Head/
Mtg Brkt/John Guest Fittings/Screws