Elkay ESRWC8 1H Series Installation manual

98074C (Rev. A - 2/05)
ESRWC8*1H ESRWC13*1H
PAGE1
With FLEXI-GUARD®
Installation/Care/Use Manual
USES HFC-134A REFRIGERANT
FIG. 1
SEE FIG.3
SEE DETAIL
ABOVE
26
28
25
44
37
22
23
30
29
6
2
8 - SEE FIG. 4
7
42
3, 4 & 5
13
43
18
14
41
15, 16 & 17
12719, 20, 21
38
39
24
45
40
46

98074C (Rev. A - 2/05)
ESRWC8*1H ESRWC13*1H
PAGE2
FIG. 2
* RECOMMENDED HEIGHT FOR ADULTS.
DECREASE HEIGHT FOR CHILDREN.
* ALTURA RECOMENDADA PARA ADULTOS.
REDUZCA PARA LOS NIÑOS.
* HAUTEUR RECOMMANDÉE POUR LES
ADULTES. INSTALLEZ PLUS BAS POUR
LES ENFANTS.
FINISHED FLOOR
PISO ACABADO
PLANCHER FINI
LEGEND/LEYENDA/LÉGENDE
A= RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38 mm) OUT FROM WALL SHUT OFF BY
OTHERS
SE RECOMIENDAUBICAR ELTUBO CORTO DE CONEXIÓNALTUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT.A1-1/2" (38 mm) FUERADE LA LLAVEDE
PASOEN LAPARED COLOCADAPORTERCEROS.
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E. CONNECTANT UNE TUYAUTERIE DE
1-1/2PO. (38mm) DEPUIS LEROBINETD'ARRÊT FOURNI PAR D'AUTRES.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN
UBICACIÓN RECOMENDADAPARAEL DRENAJE DE SALIDADEAGUA, DE 1¼” DE DIÁMETRO.
EMPLACEMENTRECOMMANDÉ POURLE DRAIN DED.E. 1-1/4" DESORTIE D’EAU.
C = 1-1/4 TRAP NOT FURNISHED**
PURGADORDE 1¼NO PROPORCIONADO**
SIPHON1-1/4 NONFOURNI**
D = ELECTRICAL OUTLET LOCATION
UBICACIÓNDE LATOMADE ELECTRICIDAD
EMPLACEMENTDE LAPRISEDE COURANT
E = INSURE PROPER VENTILATION BY MAINTAINING 4" (102mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
ASEGUREUNAVENTILACIÓNADECUADAMANTENIENDOUN ESPACIOE 4"(102mm) (MÍN.) DEHOLGURAENTRELAREJILLADE VENTILACIÓNDELMUEBLEY
LAPARED
ASSUREZ-VOUSUNE BONNEVENTILATION ENGARDANT4" (102mm) (MIN.)ENTRE LESÉVENTS DE L’ENCEINTE ET LEMUR.
F = POWER CORD 1-1/2FEET (457mm) LONG
CABLEELÉCTRICO DE 1½PIE,457 mmDELARGO
CORDOND’ALIMENTATION1-1/2'(457mm)
G = 5/16" (8mm) SCREW HOLES IN MOUNTING PLATE
AGUJEROSDETORNILLO5/16" (8mm) ENLAPLACADE MONTAJE
TROUSDE VIS5/16"(8mm) DANSLAPLAQUEDEMONTAGE

98074C (Rev. A - 2/05)
ESRWC8*1H ESRWC13*1H
PAGE3
FIG. 3
Stream height is factory set at 35 PSI. If supply pressure varies greatly from this,
remove items 31 and 32 and adjust screw on item 34. Clockwise adjustment will raise
streamandcounter-clockwise adjustmentwilllower stream.Forbest adjustment,stream
should hit basin approximately 6-1/2" (165mm) from bubbler.
NOTE:
WHEN INSTALLING REPLACEMENT BUBBLER AND
PEDESTAL, TIGHTEN NUT (ITEM 12) ONLY TO HOLD
PARTS SNUG IN POSITION.
DO NOT OVER TIGHTEN.
BASIN
IMPORTANT
ALLSERVICETOBEPERFORMED BYANAUTHORIZEDSERVICEPERSON
HANGER BRACKETS & TRAP INSTALLATION
1) Remove hanger brackets fastened to back of cooler by removing screws.
2) Mount the hanger brackets and trap as shown in Figure 2.
NOTE: Hanger Brackets and trap MUST be supported securely. Add fixture support carrier if wall will not provide adequate support.
IMPORTANT:
y5-1/2 in. (140mm) dimension from wall to centerline of trap must be maintained for proper fit.
yAnchor hanger securely to wall using all mounting holes.
3) Install straight valve for 3/8" O.D. unplated copper tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger brackets. Be certain the hanger brackets are engaged properly in the frame and wrapper.
5) Remove the access panel on the underside of the cooler and set it aside.
6) Connect water inlet line--See Note 4 of General Instructions.
7) Remove the slip nut and gasket from the trap and install them on the cooler waste line making sure that the end of the waste line fits into the trap. Assemble the slip
nut and gasket to the trap and tighten securely.
START UP
Also See General Instructions
8) Replace the front panel and secure by retightening all screws.
FIG. 4
10
11
12
89
WRAPPER
34
32
33
31 35 36

98074C (Rev. A - 2/05)
ESRWC8*1H ESRWC13*1H
PAGE4
PARTS LIST
ITEMNO. PARTNO. DESCRIPTION
36208C
27095C
30664C
70018C
31490C
70009C
56237C
56073C
40322C
56011C
55997C
75580C
66743C
66703C
50144C
70184C
70418C
36094C
36158C
35768C
35959C
66576C
40041C
40429C
50074C
20593C
20594C
75536C
31513C
66534C
55996C
27239C
40089C
40048C
15005C
61313C
40169C
50986C
See Color Table
40038C
40619C
50105C
27093C
27292C
27097C
27094C
40043C
70817C
15009C
100322740560
31525028
40493C
56092C
Power Cord
Fan Bracket
Fan Blade
Hex Nut - Fan Blade
Fan Motor
Screw (Fan Motor)
Shroud - Fan
Bubbler Assy
Orifice Assy
Housing Assy
Pedestal
Locknut
Condenser
Drier
Grommet - Compressor Mtg.
Hair Pin - Cotter
Washer
CompressorServ.Pak EMI70 HNR
Overload
Cover - Relay
Relay
Heat Exchanger
Tailpipe Assy (8 Gal)
Precooler Assy (13 Gal)
Tailpipe Gasket
Basin - Stainless Steel
Basin - Glass Filler
Screw - Basin Mtg.
ColdControl
Evaporator Assembly
Strainer
Bracket - Precooler
Cover
Button
RetainingNut
Regulator
Hex Nut
Regulator Holder
Wrapper
Strainer - Beehive
Ferrule - Tailpipe
Tailpipe Gasket
Angle-Front Corner
Bracket-Basin Mounting
Frame-Back/Bottom
Bracket-Front
Locknut
Fitting-Elbow 1/4 Stem
Nipple - Bubbler (GF)
Gasket
O-Ring
Glass Filler
Poly Tubing (Cut to Length)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18*
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
NS
PRINTED IN U.S.A.
*INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY,
REPLACE WITH SAME COMPRESSOR USED IN ORIGINAL
ASSEMBLY.
NOTE: All correspondence pertaining to any of the above wa-
ter coolers or orders for repair parts MUST include Model No.
and Serial No. of cooler, name and part number of replacement
part.
COLOR TABLE
PANELCOLOR Item No.37
PartNo.
Gray Beige
Almond
Stainless Steel
Sandalwood
Granite
Light Gray
21017C
21481C
21013C
21480C
27208C
27209C
FIG. 5
47
48
49 50
www.DrinkingFountainDoctor.com 800-518-5388