Elkay EFOA8 1D Installation manual

PAGE 1 97344C (7/98)
EFOA8*1D
With FLEXI-GUARD®
Installation/Care/Use Manual
USES HFC-134A REFRIGERANT
FIG. 1
7
27
15 & 16
14
SEE FIG. 4
26
30
28
22, 23, & 25
17, 18, 19, & 20
21
34
13
29
32
33 31 24

PAGE 2
97344C (7/98)
EFOA8*1D
FIG. 2
FINISHED FLOOR PISO ACABADO PLANCHER FINI
E = INSURE PROPER VENTILATION BY MAINTAINING 4" (102mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
ASEGURE UNA VENTILACIÓNADECUADA MANTENIENDO UN ESPACIO E 4" (102mm) (MÍN.) DE HOLGURA ENTRE LA REJILLA DE VENTILACIÓN DEL MUEBLE Y LA PARED ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 4" (102mm) (MIN.) ENTRE LES ÉVENTS DE LENCEINTE ET LE MUR.
F = POWER CORD 4 FEET (1219mm) LONG
CABLE ELÉCTRICO DE 4 PIE (1219mm), DE LARGO CORDON DALIMENTATION 4' (1219mm)
G = ALT. ELECTRICAL OUTLET LOCATION
UBICACIÓN ALT. DE LATOMA DE ELECTRICIDAD EMPLACEMENTALTERNATIF DE LA PRISE DE COURANT
H = PLUMBING ROUGH-IN CAN BE LOCATED ANYWHERE WITHIN THIS AREA.
SE PUEDE COLOCAR EL DESBASTE DE LATUBERÍA EN CUALQUIER LUGAR DENTRO DE ESTA ÁREA. ON PEUT PLACER LATUYAUTERIE DANS CETTE RÉGION.
LEGEND/LEYENDA/LÉGENDE A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38mm) OUT
FROM WALL SHUT OFF BY OTHERS
SE RECOMIENDA UBICAR EL TUBO CORTO DE CONEXIÓN AL TUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT. A 1-1/2"
(38mm) FUERA DE LALLAVE DE PASO EN LA PARED COLOCADA POR TERCEROS.
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E.
CONNECTANT UNE TUYAUTERIE DE 1-1/2 PO. (38mm) DEPUIS LE ROBINET D'ARRÊT FOURNI PAR D'AUTRES.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4 O.D. DRAIN
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDADE AGUA, DE 1¼ DE DIÁMETRO. EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE DEAU.
C = 1-1/4 TRAP NOT FURNISHED**
PURGADOR DE 1¼ NO PROPORCIONADO** SIPHON 1-1/4 NON FOURNI**
D = ELECTRICAL OUTLET LOCATION
UBICACIÓN DE LA TOMA DE ELECTRICIDAD EMPLACEMENT DE LA PRISE DE COURANT

PAGE 3 97344C (7/98)
EFOA8*1D
NOTE:
WHEN INSTALLING REPLACEMENT
BUBBLER AND PEDESTAL, TIGHTEN
NUT (ITEM 12) ONLY TO HOLD
PARTS SNUG IN POSITION.
DO NOT OVER TIGHTEN.
FIG. 4
BASIN
9
10
11
12
8
WIRING DIAGRAM
This Drawing is merely for illustrating the
components of the electrical sytem.
SENSOR RANGE ADJUSTMENT: The electronic sensor used in this cooler is factory pre-set for a "visual" range of 36
inches (914 mm). If actual range varies greatly from this or a different setting is desired, follow the range adjustment
procedure below:
A. Remove front panel of cooler.
B. Using a small tip screwdriver, rotate range adjustment screw clockwise to increase range and counterclockwise to
decrease range (See Fig. 3).
CAUTION: Complete range of sensor (24-28 inches/610-711mm) is only one turn of the adjusting screw.
C. Replace front panel.
SENSOR CONTROL: If sensor fails to operate valve mechanism or operates erratically, check the following.
A. Ensure there are no obstructions within a 40 inch (1016mm) radius in front of cooler.
B. Check wire connections at the solenoid valve and sensor. CAUTION: Make sure unit is unplugged before checking any
wiring.
C. Ensure proper operation of solenoid valve. If there is an audible clicking sound yet no water flows, look for an obstruction
in the valve itself or elsewhere in the water supply line.
RANGE ADJUSTMENT SCREW
30
6
31
32
34
5
2
1
TO PRECOOLER
33
TO SOLENOID VALVE (ITEM 32)
FIG. 3
TO EVAP. ASSY.(ITEM 29)

PAGE 4
97344C (7/98)
EFOA8*1D
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
ELKAY MANUFACTURING COMPANY  2222 CAMDEN COURT  OAK BROOK, IL 60523  630.574.8484
PRINTED IN U.S.A.
PARTS LIST 115V
ITEM NO. PART NO. DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22*
23
24
25
26
27
28
29
30
31
32
33
34
RIGHT
PANEL
FRONT
PANEL
LEFT
PANEL
COLOR
TABLE
Gray Beige
Almond
Stainless Steel
Sandalwood
Granite
20622C
21460C
20624C
21458C
27165C
20623C
21461C
20625C
21459C
27168C
27272C
27273C
27270C
27274C
27271C
Cover
Clip
Regulator Retaining Nut
Regulator
Hex Nut
Regulator Holder
Basin
Bubbler Assembly
Orifice Assembly
Housing Assembly
Pedestal
Bubbler Locknut
Cold Control
Power Cord
Condenser
Fan Shroud
Fan Motor
Fan Blade
Fan Bracket
Fan Blade Nut
Drier
Compressor Serv. Pak
Overload/Relay Assembly
Receptor-Drain
Electrical Shield
Strainer
Precooler
Heat Exchanger
Evaporator
Regulator Bracket
Sensor (clear)
Solenoid Valve Assembly
Cross Brace
Screw-Evaporator Mtg
40116C
70254C
15005C
61313C
40045C
50986C
27316C
51349C
40322C
50934C
50168C
70012C
31513C
35890C
66431C
21516C
31490C
30664C
20239C
70018C
66201C
35787C
31034C
50368C
194243901550
55996C
45678C
66255C
66505C
27278C
31516C
35891C
27279C
75568C
*INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY,
REPLACE WITH SAME COMPRESSOR USED IN ORIGINALASSEMBLY.
NOTE: All correspondence pertaining to any of the above water coolers
or orders for repair parts MUST include Model No. and Serial No. of cooler,
name and part number of replacement part.