Elkay EIOA4 1B Series Installation manual

97062C (Rev. A - 3/98)
EIOA4/8*1B, EIOA4/8*2B
PAGE 1
With FLEXI-GUARD®
Installation/Care/Use Manual
USES HFC-134A REFRIGERANT
FIG. 1
59
39
37
58
SEE FIG. 4
48, 49, 50, 51, 52
54
58
41, 42, 43
53
36
57
28
55
23
20, 21, 22
30
24, 25, 26, 27
SEE FIG. 3
47
38
59
12 44
45, 46,
56, 60
40

97062C (Rev. A - 3/98)
EIOA4/8*1B, EIOA4/8*2B
PAGE 2
FIG. 2
FINISHED FLOOR PISO ACABADO PLANCHER FINI
*ADA REQUIREMENT *REQUISITO DE A.D.A. *EXIGENCE ADA
D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX
CAJA RECESIVA DEALAMBRES (3) DE SUMINISTRO ELÉCTRICO BOÎTE ENCASTRÉE DALIMENTATION ÉLECTRIQUE (3) FILS
E = INSURE PROPER VENTILATION BY MAINTAINING 6" (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO
WALL.
ASEGURE UNA VENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 6" (152 mm) (MÍN.) DE HOLGURA ENTRE LA REJILLA DE VENTILACIÓN DEL MUEBLE Y LA PARED ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 6" (152 mm) (MIN.) ENTRE LES ÉVENTS DE LENCEINTE ET LE MUR.
F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL
AGUJEROS DE LAS TUERCAS DE 7/16 PARA SUJETAR LA UNIDAD A LA PARED TROUS DÉCROUS 7/16 POUR FIXER LAPPAREILAU MUR
LEGEND/LEYENDA/LÉGENDE A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38 mm) OUT
FROM WALL SHUT OFF BY OTHERS
SE RECOMIENDA UBICAR ELTUBO CORTO DE CONEXIÓN AL TUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT. A1-1/2"
(38 mm) FUERA DE LALLAVE DE PASO EN LA PARED COLOCADAPOR TERCEROS.
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E.
CONNECTANT UNE TUYAUTERIE DE 1-1/2 PO. (38 mm) DEPUIS LE ROBINET D'ARRÊT FOURNI PAR D'AUTRES.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4 O.D. DRAIN
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDADEAGUA, DE 1¼ DE DIÁMETRO. EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE DEAU.
C = 1-1/4 TRAP NOT FURNISHED**
PURGADOR DE 1¼ NO PROPORCIONADO** SIPHON 1-1/4 NON FOURNI**

97062C (Rev. A - 3/98)
EIOA4/8*1B, EIOA4/8*2B
PAGE 3
SENSOR RANGE ADJUSTMENT: The electronic sensor used in this cooler is factory pre-set for a "visual" range of 36
inches (914 mm). If actual range varies greatly from this or a different setting is desired, follow the range adjustment
procedure below:
A. Remove front panel of cooler.
B. Using a small tip screwdriver, rotate range adjustment screw clockwise to increase range and counterclockwise to
decrease range (See Fig. 3).
CAUTION: Complete range of sensor (24-28 inches/610-711mm) is only one turn of the adjusting screw.
C. Replace front panel.
SENSOR CONTROL: If sensor fails to operate valve mechanism or operates erratically, check the following.
A. Ensure there are no obstructions within a 40 inch (1016mm) radius in front of cooler.
B. Check wire connections at the solenoid valve and sensor. CAUTION: Make sure unit is unplugged before checking any
wiring.
C. Ensure proper operation of solenoid valve. If there is an audible clicking sound yet no water flows, look for an obstruction
in the valve itself or elsewhere in the water supply line.
17
14
13
NOTE: WATER FLOW DIRECTON
RANGE
ADJUSTMENT
SCREW
7
14
10
6
14
FIG. 3
HANGER BRACKETS & TRAP
INSTALLATION
1) Remove hanger bracket fastened to back of cooler by re-
moving one (1) screw.
2) Mount the hanger bracket and trap as shown in Figure 2.
NOTE: Hanger Bracket MUST be supported securely. Add
fixture support carrier if wall will not provide adequate sup-
port.
IMPORTANT:
7-3/4 in. (197mm) dimension from wall to centerline of
trap must be maintained for proper fit.
Anchor hanger securely to wall using all six (6) 1/4 in. dia.
mounting holes.
3) Install straight valve for 3/8" O.D. tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger bracket. Be certain the
hanger bracket is engaged properly in the slots on the
cooler back as shown in Figure 2.
5) Loosen the two (2) screws holding the lower front panel at
the bottom of cooler base and two (2) screws at the top.
Remove the front panel and set aside.
6) Connect water inlet line--See Note 4 of General Instruc-
tions.
7) Remove the slip nut and gasket from the trap and install
them on the cooler waste line making sure that the end of
the waste line fits into the trap. Assemble the slip nut and
gasket to the trap and tighten securely.
START UP
Also See General Instructions
8) Stream height is factory set at 35 PSI. If supply
pressure varies greatly from this, adjust screw, ac-
cessible by removing front panel (Item 7, Fig. 3).
CW adjustment will raise stream and CCW adjust-
ment will lower stream. For best adjustment, stream
should hit basin approximately 6-1/2 (165mm) from
bubbler.
9) Replace the front panel and secure by retightening
four (4) screws.
ITEM NO. PART NO.
Panel-Bottom Dispenser
Bracket-Valve Mounting
Sensor-Clear (115V)
Sensor-Clear (230V)
Solenoid Valve (115V)
Solenoid Valve (230V)
Panel-Right Side
Panel-Left Side
Panel-Front
Elbow 1/4 Stem x 1/4 O.D.
Fitting 1/4 NPTF x 1/4 O.D.
Nut-Cover Unplated
Screw-#6-32 x 1/2" Lg. PHMS
Screw-#10 x 1/2" Lg. THSM
Clip
Screw-#8 x 5/8" Lg. Torx/Slot
Hex Nut
Retaining Nut
Regulator
Holder-Regulator
Screw-#10 x 1/2" Lg. HHSM
22897C
26729C
31516C
35783C
31272C
35784C
See Color Table
See Color Table
See Color Table
70817C
75507C
40116C
70644C
75532C
70254C
70864C
40045C
15005C
61314C
50986C
70002C
Item No. 5
Part No.
COLOR TABLE
Bronzetone
Gray Beige
Almond
Stainless Stl
Sandalwood
Granite
27502C
23015C
23016C
22822C
23017C
23020C
27432C
23008C
23009C
22814C
23010C
23013C
27591C
23161C
23162C
23137C
23164C
27217C
PANEL
COLOR
Item No. 6
Part No.
Item No. 7
Part No.
11 2
15
11 3
57 4
12 14
5
16
18 8919 9
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
DESCRIPTION

97062C (Rev. A - 3/98)
EIOA4/8*1B, EIOA4/8*2B
PAGE 4
PRINTED IN U.S.A.
PARTS LIST 115V
ITEM NO. PART NO.
20
21
22
23
24, 24a
24b
25
26, 26a
26b
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44*
44a*
44b*
44c*
45
45a
45b
45b
45c
46, 46a
46b
46b
46b
46c
47, 47b
47a
47c
48
49
50
51
52
53
54
55
56
57
58
59
60c
NS
Item No. 38
Part No.
COLOR TABLE
Bronzetone
Gray Beige
Almond
Stainless Steel
Sandalwood
Granite
27490C
22967C
22968C
22862C
22969C
22972C
27486C
22960C
22961C
22854C
22962C
22965C
27498C
22953C
22954C
22955C
22956C
27214C
Evaporator Assembly
Clip - Evap. Retaining
Plug - Drain
Power Cord
Fan Blade
Fan Blade
Hex Nut - Fan Blade
Fan Motor 115V
Fan Motor 115V
Screw - Fan Motor
Shroud - Fan
Screw - #8-18 x 3/8" Lg. (Fan Shroud)
Clip (Front and Rear Panels)
Bubbler Assembly Module
Bubbler Assembly Module - Bronzetone
Orifice Assembly
Orifice Assembly - Bronzetone
Guard
Pedestal
Pedestal - Bronzetone
Locknut
Condenser
Drier
Panel -Right Rear
Panel -Left Rear
Panel - Front Lower
Stud - Compressor Mtg.
Grommet - Compressor Mtg.
Clip - Compressor Mtg.
Compressor Serv. Pak FF7.5HBK
Compressor Serv. Pak FF6HBK
Compressor Serv. Pak AE3425Y
Compressor Serv. Pak EM65
Overload/Relay 1.350.358
Overload/Relay 1.350.356
Relay 9660-042-166
Overload MRP26ALL-69
Overload/Relay P600B/427NFBYY
Cover - Relay
Cover - Terminal
Overload Spring
Bale Strap
Cover - Relay
Heat Exchanger
Heat Exchanger
Heat Exchanger
Drain Tube
Gasket - Drain
Ring Support - Drain
Clamp - Drain Gasket
Hex Nut #10-32
Cold Control
Adaptor - Basin
Basin
Basin - Bronzetone
Cover - Electrical Shield
Cover-Dispenser Bottom
Screw-#10 x 1/2"Lg. HHSM
Strainer
Capacitor - Run
Hanger Bracket
62220C
70767C
70772C
31483C
30699C
30664C
70018C
31490C
31491C
70009C
22899C
38417001
75524C
97276C
97277C
40322C
40066C
50934C
50168C
50373C
70012C
62152C
66202C
See Color Table
See Color Table
See Color Table
101516143550
100806740570
19037000
35767C
35761C
35807C
35947C
31025C
31026C
35801C
35795C
31039C
35766C
30181C
30180C
30182C
35768C
66214C
66215C
66386C
40614C
50400C
50401C
70444C
70016C
31513C
See Color Table
MAD21874
27534C
194243901550
See Color Table
70002C
55996C
35935C
400660943730
PANEL
COLOR
Item No. 39
Part No.
Item No. 54
Part No.
Item No. 57
Part No.
Item No. 40
Part No.
51552C
51551C
51552C
51551C
51552C
51551C
55930C
55931C
55930C
55931C
55930C
55931C
DESCRIPTION
*INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY,
REPLACE WITH SAME COMPRESSOR USED IN ORIGINAL
ASSEMBLY.
NOTE: All correspondence pertaining to any of the above
water coolers or orders for repair parts MUST include Model
No. and Serial No. of cooler, name and part number of re-
placement part.
WIRING DIAGRAM
This Drawing is merely for illustrating the
components of the electrical system.
NOTE:
WHEN INSTALLING REPLACEMENT BUBBLER
AND PEDESTAL, TIGHTEN NUT (ITEM 35)
ONLY TO HOLD PARTS SNUG IN POSITION.
DO NOT OVER TIGHTEN.
BASIN
32
33
34
35
31
PARTS LIST 230V
ITEM NO. PART NO.
26
44*
45
46
Fan Motor
Compressor Serv. Pak
Overload/Relay
Cover-Relay
31431C
35763C
31024C
35768C
DESCRIPTION
FIG. 4
CAUTION: Cleaning of Bronzetone Models requires
special care. Outer surfaces must be cleaned with a mild
detergent or mixture of vinegar and water only, rinsed and
wiped dry. Abrasive and acidic cleaners may eventually
damage the Bronzetone finish.
www.DrinkingFountainDoctor.com 800-518-5388