Elkay LVRC8-BAC Series Installation manual

Page 1 1000001748 (Rev. C - 12/17
LVRC8*1C
LVRC8-BAC Series Water Coolers
INSTALLATION, CARE & USE MANUAL
USES HFC-134A REFRIGERANT

Page 21000001748 (Rev. C - 12/17)
LVRC8*1C
2
6
14
5
24
20
21
21
21
4
See Fig. 5
10
12
1
3
11
See Fig. 3
21
19
23
24
16
27
30
31
28
7
5, 9
13
5
18
25
21
Uses HFC-134A refrigerant
Fig. 1
Filter location
Note: Danger! Electric shock hazard. Disconnect power before servicing unit.
27

Page 3 1000001748 (Rev. C - 12/17
LVRC8*1C
C
L
ORIFICE HEIGHT
RIM HEIGHT
13 7/8"
352mm
E
8"
203mm
21 3/8"
543mm
18 3/8"
467mm
D A
F
5 3/4"
146mm
2 1/2"
62mm
11/16"
18mm
FINISHED FLOOR
HANGER BRACKET
4 9/16"
116mm
1 1/2"
38mm
18 5/8"
473mm
5 3/4"
146mm
3 1/2"
89mm
27" *
686mm
B
12 5/16"
313mm
6 1/4"
159mm
32 15/16"
837mm
2 5/8"
67mm
5/16" (8mm) DIA. (5 HOLES)
31 7/8"
810mm
30 15/16"
786mm
FILTER
C
25" 635mm
4 1/2" 114mm
FILTER
LEGEND A = RECOMMENDED WATER SUPPLY LOCATION. SHUT OFF VALVE (NOT FURNISHED) TO ACCEPT 3/8” O.D. UNPLATED COPPER TUBE. B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN C = 1-1/4 TRAP NOT FURNISHED D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX E = INSURE PROPER VENTILATION BY MAINTAINING 6” (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL. F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL
REDUCE HEIGHT BY 3” FOR INSTALLATION OF CHILDREN’S ADA COOLER

Page 41000001748 (Rev. C - 12/17)
LVRC8*1C
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN
AUTHORIZED SERVICE PERSON
HANGER BRACKETS & TRAP
INSTALLATION
1) Remove hanger bracket fastened to back of
cooler by removing one (1) screw.
2) Mount the hanger bracket and trap as shown
in Figure 2.
NOTE: Hanger Bracket MUST be supported
securely. Add xture support carrier if wall will
not provide adequate support.
IMPORTANT:
• 6 1/4 in. (159mm) dimension from wall to cen-
terline of trap must be maintained for proper t.
• Anchor hanger securely to wall using all ve (5)
1/4 in. dia. mounting holes.
3) Install straight valve for 3/8” O.D. tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger bracket. Be
certain the hanger bracket is engaged properly
in the slots on the cooler back as shown in Figure
2.
5) Loosen the two (2) screws holding the lower
front panel at the bottom of cooler base and
two (2) screws at the top (Use torx bits sold
separately). Remove the front panel and set
aside.
6) Connect water inlet line--See Note 4 of General
Instructions.
7) Remove the slip nut and gasket from the trap
and install them on the cooler waste line mak-
ing sure that the end of the waste line ts into
the trap. Assemble the slip nut and gasket to
the trap and tighten securely.
START UP
Also See General Instructions
8) Stream height is factory set at 45-50 PSI. If
supply pressure varies greatly from this, adjust
screw using the access hole in the pushbutton
(insert screwdriver). CW adjustment will raise
stream and CCW adjustment will lower stream.
For best adjustment, stream should hit basin
approximately 6-1/2” (165mm) from bubbler.
Fig. 3
Basin
1
VANDAL RESISTANT BUBBLER DETAIL
ITEM
NO.
Filter Assy - 3000 Gallon
Filter Head Assy
Screw #8-18 X .75 PH
Tube - 3/8" Inlet
Bracket
3/8" x 1/4" John Guest Ftg
1
2
3
4
5
6
0000000376
0000000469
0000000471
0000000484
0000000420
72460104
DESCRIPTION
PART
NO.
WATERSENTRY®FILTER PARTS LIST
(See Fig. 4)
FIG. 4
6
3
5
4
1
2

Page 5 1000001748 (Rev. C - 12/17
LVRC8*1C
33
Fig. 5
1
5
25
27 (8)
1
1
30
5
5
28
31
28
15
8
22
22
22
14
27
17
26
32
22
22
34
27
29
27
8
15
27 (6)
22
1
9
5
18
5
5
27
27
29

Page 61000001748 (Rev. C - 12/17)
LVRC8*1C
PRINTED IN U.S.A.
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
97446C
98777C
98775C
98778C
98856C
98773C
27124C
28596C
110868642550
35870C
36322C
0000000238
1000001602
98530C
28617C
56092C
55931C
45930C
66703C
98724C
70002C
1000001906
98776C
75524C
0000000966
22897C
0000001190
22955C
70864C
28525C
28528C
28519C
28522C
28516C
75523C
28551C
Kit - Vandal Resistant Bubbler Replacement
Kit - Compressor Mounting Hardware
Kit - Fan Motor/Blade/Nut/Shroud
Kit - Heat Exchanger/Drier
Kit - Drain/Elbow/Strainer/Plug/Gasket/Washer
Kit - Cold Control/Screws
Cover - Cold Control
Panel - Screen
Screw - #10-24 x .75 Socket Hd.
Power Cord
Compressor Serv. Pak EMI 70
Kit - Relay/OverLoad/Cover
Kit - Elbow - 5/16” x 1/4” (3 Pack)
Kit - Regulator/Holder/Retaining Nut
Screen - VR
Tubing - Poly (Cut To length)
Cover - Dispenser Bottom
Tube - Drain
Drier
Kit - Evaporator Replacement
Screw - #10 x 1/2” Lg. HHSM
Kit - Pushbutton (VR)
Kit - Condenser/Drier
Clip (Front & Rear Panels)
Kit - Basin Replacement/Gasket/Strainer/Tube/
Elbow/Plug/Nut/Seal
Panel - Bottom Dispenser
Kit - #10 Pinned Torx Screws/T-25 Bit
Panel - Front Lower (S)
Screw - #8 x .62 Torx/Slot
Panel - RH Rear (S)
Panel - LH Rear (S)
Panel - RH Dispenser Side (S)
Panel - LH Dispenser Side (S)
Panel - Dispenser Front (S)
Torx Tool - T20
Hanger Bracket
PART NO. DESCRIPTION
*REPLACE WITH SAME COMPRESSOR USED IN
ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the
above water coolers or orders for repair parts MUST
include Model No. and Serial No. of cooler, name and
part number of replacement part.
1
2
3
4
5
6
7
8
9
10
*11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Sold Separate
NS
ITEM NO.
115V PARTS LIST
NS = NOT SHOWN