Elkay EMASM Guide

0000001496 (Rev. F - 08/17)
Page 1
EMASM*A
Installation and Use Manual
EMASM Surface Mount Bottle Filling Station
To assure you install this model easily and correctly, PLEASE READ THESE
SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK
YOUR INSTALLATION FOR COMPLIANCE WITH ALL PLUMBING, ELECTRICAL
AND OTHER APPLICABLE CODES. FOLLOW ALL WARNINGS AND CAUTIONS
CAREFULLY. After installation, leave these instructions with the customer for future
reference.
Installer
Warnings
1. Use with clean, clear, fresh potable drinking water only! Do not use with water that is microbiologically
unsafe or of unknown quality without adequate disinfection before the system.
2. These products are designed to operate on 20 to 105 PSI supply line pressure. If inlet pressure
is above 105 PSI, a pressure regulator must be installed in supply line. Any damage caused by
reason of connecting this product to supply line pressure lower than 20 PSI or higher than
105 PSI is not covered by warranty.
IMPORTANT
THIS IS AN INDOOR APPLICATION ONLY!
ALL SERVICE TO BE PERFORMED BY AN
AUTHORIZED SERVICE PERSONNEL.
TOOLS/ITEMS REQUIRED
BUT NOT SUPPLIED
- SERVICE STOP VALVE WITH 3/8"
COMPRESSION OUTLET
- FASTENERS FOR WALL TYPE (8 REQ’D.)
- SLIP JOINT DRAIN UNION OR
COMPRESSION CLAMP
- 5/32" HEX-WRENCH

0000001496 (Rev. F - 08/17)
EMASM*A
Page 2
FINISHED FLOOR
6 1/4"
159mm
4"
102mm
ADA DEPTH
27"
686mm
ADA HEIGHT
38 1/2"
977mm
42 1/8"
1069mm
‰OF BUTTON
46 1/2"
1182mm
48"
1219mm
ADA HEIGHT
64 3/8"
1635mm
FINISHED FLOOR
7"
178mm
7"
178mm ‰
22"
559mm
40 1/2"
1029mm
45 5/8"
1159mm
44"
1118mm
6"
152mm
MINIMUM
CLEARANCE
3/8"
9.5mm
WATER
INLET
"A"
3"
76mm
1-1/4"
31.7mm
DRAIN
"B"
FILTER USED ONLY
IN LMASMB UNITS
7/16" X 3/4"
1
1mm X 19mm
OBROUND
MOUNTING
HOLE (6)
"C"
O
3/8"
8mm (6)
MOUNTING BOLT
DRAIN TRAP
CUSTOMER
SUPPLIED
B CA
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
A B C
FIG. 1
ROUGH-IN
EMASM
ADA STAND-ALONE MOUNTING
LEGEND:
A = RECOMMENDED WATER SUPPLY LOCATION ; 1/2" IPS MAXIMUM PIPE SIZE. SERVICE STOP VALVE NOT FURNISHED.
B = RECOMMENDED WASTE LOCATION. WASTE SHOWN IN WALL BUT MAY BE BEHIND WALL.
OUTLET 1-1/4” O.D. (TRAP NOT FURNISHED)
C =7/16" X 3/4" OBROUND MOUNTING HOLES FOR FASTENING BACKPLATE TO WALL.
FIG. 2
IMPORTANT!
INSTALLATION NOTES:
• Ensure wall is structurally sound to bear the loads imparted by the Surface Mount Bottle Filler.
• Ambient air temperature limits: 10°C - 38°C (50°F - 100.4°F). Climate Class SN-ST.
• Not suitable for installation in areas where water jets could be used.

0000001496 (Rev. F - 08/17)
Page 3
EMASM*A
40 1/2"
1029mm
45 5/8"
1159mm
44"
1118mm
3"
76mm 48"
1219mm
ADA HEIGHT
42 1/8"
1069mm
‰OF BUTTON
46 1/2"
1182mm
6 1/4"
159mm
38 1/2"
977mm
64 3/8"
1634mm
7"
178mm 7"
178mm
22"
559mm
‰
3/8"
9.5mm
WATER
INLET
"A"
1-1/4"
31.7mm
DRAIN
"B"
17 7/8"
454mm
25 7/8"
658mm
7/16" X 3/4"
11mm X 19mm
OBROUND
MOUNTING
HOLE (6)
"C"
ADA HEIGHT
WATER COOLER
4"
102mm
ADA DEPTH
27"
686mm
ADA
HEIGHT
FINISHED FLOOR
FILTER USED ONLY
IN LMASMB UNITS
O
3/8"
8mm (6)
MOUNTING
BOLT
6"
152mm
MINIMUM
CLEARANCE
FINISHED FLOOR
DRAIN TRAP
CUSTOMER
SUPPLIED
ROUGH-IN
EMASM
ADA ABOVE COOLER MOUNTING
FIG. 3
LEGEND:
A = RECOMMENDED WATER SUPPLY LOCATION ; 1/2" IPS MAXIMUM PIPE SIZE. SERVICE STOP VALVE NOT FURNISHED.
B = RECOMMENDED WASTE LOCATION. WASTE SHOWN IN WALL BUT MAY BE BEHIND WALL.
OUTLET 1-1/4” O.D. (TRAP NOT FURNISHED)
C =7/16" X 3/4" OBROUND MOUNTING HOLES FOR FASTENING BACKPLATE TO WALL.
IMPORTANT!
INSTALLATION NOTES:
• Ensure wall is structurally sound to bear the loads imparted by the Surface Mount Bottle Filler.
• Ambient air temperature limits: 10°C - 38°C (50°F - 100.4°F). Climate Class SN-ST.
• Not suitable for installation in areas where water jets could be used.

0000001496 (Rev. F - 08/17)
EMASM*A
Page 4
INSTALLATION INSTRUCTIONS
ALCOVE
DRAIN TRAY
TOP COVER
FRONT VIEW REAR VIEW
BACK PANEL
OUTER
WRAPPER
Pre-Installation (reference Rough-In, Fig. 1 and Fig. 3)
1. Ensure Wall is structurally sound to bear the loads imparted by the EMASM Bottle Filler
(On-Wall Bottle Filler). If necessary, install a Wall Support Carrier (not supplied).
2. Ensure Water Supply Line and Drain Line are sized and located as specied the Rough-in diagram.
3. Attach Service Stop Valve (not supplied) to Water Supply line orienting the 3/8"O.D. female compression
outlet horizontally to the left. Purge water line and test for leakage. Correct any leakage.
4. Ensure package contains the following components:
Wall Mounting (reference Rough-In, Fig. 1 and Fig. 3)
1. Remove Top Cover from Bottle Filler by removing two (2) screws from top of unit. Use a 5/32" hex wrench (not
supplied).
2. Remove Bottom Cover from Bottle Filler by removing two (2) screws from bottom of unit. Use a 5/32" hex
wrench (not supplied).
3. With the Top and Bottom Covers removed, the Back panel is now free to be removed from Bottle Filler.
4. Fasten Back Panel to structurally secure wall through ve 7/16" obround holes with fasteners appropriate for
wall type. Locate Back Panel as specied in Rough-In. If necessary, attach to Wall Support Carrier (not supplied).
5. Ensure Back Panel is not obstructed by the roughed-in Water and Drain Lines. If Back Panel is prevented from
seating properly, reposition Water and/or Drain Lines slightly until the Bottom Cover ts easily.
6. Before hanging the On-Wall Bottle Filler, ensure the Insulated Waterline is routed inside of the Wrapper If
outside the Wrapper, reposition to inside or else the unit cannot be installed properly.
7. Hang the Bottle Filler onto the Back Panel, aligning two tabs into the top of the Back Panel.
8. Secure Bottle Filler to Back Panel by replacing Top Cover on top of unit and fastening with two (2) supplied
screws.
9. Replace the Bottom Cover on bottom of the unit and fasten in place with two (2) supplied screws.
EMASM UNIT SHOWN
INSULATED
WATERLINE
BOTTOM COVER
DISPENSING
NOZZLE
TOP SCREWS
BOTTOM SCREWS
INSTALLER TO SUPPLY:
SHUT OFF VALVE

0000001496 (Rev. F - 08/17)
Page 5
EMASM*A
Plumbing Connections
• Ensure lines and ports remain clean and free of contaminants during assembly.
• Purge each component if necessary.
• To ensure quick-connect connections seal properly, follow instructions per Figure 2, Page 2.
Instruction for Use
1. Place container under the dispenser nozzle and depress the actuator button. Hold until container is lled to the level
desired.
2. To stop water ow, release actuator button. Pull container away from dispenser nozzle.
1. Connect water supply line to unit:
2. Connect the 3/8"O.D. Copper tube from the in-line strainer to the 3/8" to the Service Stop Valve.
3. Connect the 1-1/4"O.D. Drain Tray Outlet to the in-wall Drain Line using a Slip Joint Drain Union or compression clamp
(not supplied). Tighten all connections water tight.
4. Turn water supply on, inspect for leaks and correct any leaks before continuing.
Connect Plumbing Lines
PRINTED IN U.S.A.
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 • www.elkay.com
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
DESCRIPTION
1000001673
98546C
1.0 GPM REGULATOR KIT- EMASM
AERATOR KIT
REPLACEMENT PARTS
PART NO.
REGULATOR
AERATOR