elmeasure SL VDC User manual

Universal Auxiliary supply (24-300V AC/DC).
Parameters VDC & ADC.
1 row 4 digit display.
User configurable (Editable) password.
Auto-scaling of kilo decimal point.
PG/SLDC/V1/0820
[email protected]
Toll Free: 1800 120 5048
SL VDC | SL ADC | µA VDC | µA ADC
www.elmeasure.com
User Manual
Head office & Manufacturing Unit 1
Plot N0.: 47-P, KIADB Hardware Park,
Huvinayakanahalli, Bengaluru - 562 149,
Karnataka INDIA.
Manufacturing Unit 2
Goutham Garden, No.4, Veerapandi,
Coimbatore - 641019 Tamil Nadu, INDIA
T: 0422 2697200. TF: 0422 2695200
E: contact[email protected]
Elmeasure India Private Limited
www.elmeasure.com
3. PROGRAMMING MODE
2. KEY & DISPLAY INDICATION
Value Indication
Kilo
To view the parameters Downwards.
To view the parameters Upwards.
PRG
COM
Communication
MINUS
To view the parameters Upwards.
To view the parameters Downwards.
Kilo
Minus
To view the
parameters Upwards.
To view the parameters
Downwards.
Kilo
Minus
3.1 Programming Keys
Press Up + Down to enter setup mode .
Enter Password (default 1000) blinking of digit indicates Edit is possible.
Press Down to decrement value from 9 to 1.
Press Up to move to the next digit till 4th digit .
If Password is correct, editing is possible.
Press Down to view and press Up key to edit.
Press Down to decrement values or to select from available options.
Press Up to save the value / parameter.
Press Down to edit next parameter till end of last parameter &
display screen will prompt display reads (YES).
Press Down to change to (NO) .
Press Up to save.
To decrement
value
To select / Edit &
save Value
3.2 Setup Procedure
MINUS
SL VDC | SL ADC
µA ADC
µA VDC
Baud rate (bA)
Parity (Pr)
Device Id (dU.)
4.800K/9.600K/19.20K/
38.40K
Odd/ no(none)/EVEn
1.000 to 247.0
Password (PW) 1000 to 9999
1. FEATURES
PT Primary(P.P)*
CT Primary(C.P)**
Programming
Parameter
3.3 Display
Default
0.100 to 999.9kV
0.1 to 999.9kA
Option/Range
CT Shunt(C.S)** 50 to 100
Offset 0.t.F.S to 4.t.F.S
Save Yes or No
Note: *For VDC
**For ADC
4. WIRING DIAGRAM
SL ADC
SL ADC
RS 485
DC
Source
Input AUX
0-20mA DC 80-300
VAC/DC
L
N
RS 485
AUX
80-300
VAC/DC
L
N
DC
Source
LOAD
SHUNT
0-75mV DC
Input

µA ADC
µA VDC
SL VDC
1) Meter display does not turn ON.
a) Check that there is power supply applied on AUX supply terminals.
b) Check fuse connection (Use fuse connection of specified ratings).
2) Data displayed / reading incorrect.
a) Check that CT/PT ratios are properly set.
b) Check if proper configuration mode is correctly set.Star/Delta/1Phase
3) RS485 communication does not work.
a) Check baud rate & parity maintained in the connected computers is same
as meter.
b) Memory mapping in software is correct.
c) Check device ID of meter is unique & properly maintained.
d) Check converter is working properly.
Manufacturer assumes no responsibility for a hazard or damage caused by
incorrect or non-application of any of the instructions mentioned herein.
ELMEASURE shall not be liable for any consequential or resulting injury or for loss,
damage or expense directly or indirectly from the use of this product under any
circumstances.
ELMEASURE does not claim any responsibility for the damage caused by using the
product directly or indirectly as sufficient care has been taken to provide all
information regarding the product. The user is advised to use according to the
operating instructions, professional practices, wiring rules, codes, safety
regulations applicable to the given installation.
During normal operation of this instrument, hazardous voltages are present at the
rear terminals, which may cause injury or death. Installation, disconnection or
removal of the meter should be carried out only by qualified, trained personnel,
after de-energizing connected circuit. The warranty will become void incase the
seal is broken, improper installation as well as improper grounding.
6. TROUBLE SHOOTING
7. INFORMATION
8. CAUTION
41
96
90
90
96
+2
90-0
+2
90-0
30
5. MECHANICAL SPECIFICATION
48
96
56
42
90
+2
42-0
+2
90-0
45
SLEEK
Micro Alpha
RS 485
AUX
80-300
VAC/DC
L
N
Input
0-48V DC
DC
Source
DC
Source
N
L
0-48V DC
µA ADC
DC
Source
N
L
0-20mA DC
N
L
DC
Source
LOAD
SHUNT
0-75mV DC