Schmidt KXE-50 User manual

Tension Meter
KXE Series
Model KXE
Edition KXE 02.1.E
Operating Instructions
Valid as of: 01.09.2011 • Please keep the manual for future reference!
S C H M I D T
c o n t r o l i n s t r u m e n t s

2
Contents
1 Warranty and Liability .............................................................................................. 3
1.1 Notices within the Operating Instructions............................................................... 3
1.2 Responsibilities of the Operating Company ........................................................... 4
1.3 Responsibilities of the Personnel ........................................................................... 4
1.4 Informal Safety Measures ...................................................................................... 4
1.5 Training of the Personnel ....................................................................................... 4
1.6 Intended Use.......................................................................................................... 4
1.7 Dangers in Handling the Device............................................................................. 4
1.8 Copyright................................................................................................................ 5
1.9 Declaration of Conformity, RoHs II and WEEE Registration.................................. 5
2 Available Models....................................................................................................... 5
2.1 Specifications ......................................................................................................... 5
2.2 Delivery Includes.................................................................................................... 6
2.3 Unpacking .............................................................................................................. 6
3 Initial Setup and Operating Procedure ................................................................... 6
3.1 Notes Before Starting Measurement...................................................................... 7
3.1.1 ID Plate, CE Mark, Calibration Label................................................................ 7
3.2 Operating Elements.................................................................................................. 7
3.3 Setup...................................................................................................................... 8
3.3.1 Charging the Battery......................................................................................... 8
3.3.2 Switch-On......................................................................................................... 8
3.3.3 Switch-Off......................................................................................................... 8
3.3.4 Reversing the Display....................................................................................... 9
3.3.5 Zero Adjustment of the Measuring Position...................................................... 9
3.4 Operating Procedure............................................................................................ 10
3.4.1 Switching on Damping Mode.......................................................................... 11
3.4.2 Changing the Damping Factor........................................................................ 11
3.5 Memory Modes .................................................................................................... 12
3.5.1 Memory Mode Selection................................................................................. 13
3.5.1.1 Data Logging in Mode “S” STANDARD .............................................. 14
3.5.1.2 Data Logging in Mode “C” CONTINUOUS.......................................... 14
3.5.1.3 Data Logging in Mode “L” LIMIT ......................................................... 15
3.5.1.4 Data Logging in Mode “F” FAST ......................................................... 16
3.5.2 Recalling the Stored Tension Values ............................................................. 17
3.5.2.1 Recalling the Stored Tension Values in Mode “S“ STANDARD.......... 17
3.5.2.2 Recalling the Stored Tension Values in Mode “C“ CONTINUOUS..... 18
3.5.2.3 Recalling the Stored Tension Values in Mode “L“ LIMIT..................... 19
3.5.2.4 Recalling the Stored Tension Values in Mode “F“ FAST .................... 20
3.5.3 Clearing the KXE Memory .............................................................................. 21
3.5.4 Memory Function HOLD................................................................................. 21
3.6 Error Messages.................................................................................................... 22
3.7 Static Verification of Measuring Accuracy............................................................ 22
4 PC Communication (USB Interface)..................................................................... 23
4.1 The TENSION INSPECT Program....................................................................... 23
4.2 WINDOWS Terminal Program ............................................................................. 23

3
1 Warranty and Liability
In principle, the supply of the device is subject to our “General Conditions of Sale and
Delivery.” These have been provided to the operating company on conclusion of the
contract, at the latest.
Warranty:
- SCHMIDT tension meters are warranted for 12 months.
Parts subject to wear, electronic components and measuring springs are not covered by
the warranty. No warranty or liability will be accepted for bodily injury or property damage
resulting from one or several of the following causes:
- Misuse or abuse of the device.
- Improper mounting, commissioning, operation and maintenance of the device
(e.g. verification interval).
- Operation of the device if any safeguards are defective or if any safety and protection
precautions are not properly installed or not operative.
- Failure to comply with the notices in the Operating Instructions regarding transport,
storage, mounting, commissioning, operation, maintenance and setup of the device.
- Any unauthorized structural alteration of the device.
- Insufficient inspection of device components that are subject to wear.
- Opening the device or improper repair work.
- Disasters caused by the effects of foreign objects or by force majeure.
1.1 Notices within the Operating Instructions
The fundamental prerequisite for the safe handling of this device and its troublefree opera-
tion is the knowledge of the basic safety notices and safety instructions.
These Operating Instructions contain the most important notices for the safe operation of
the device.
These Operating Instructions, in particular the safety notices, must be observed by any
person who works with the device. In addition, the local applicable rules and regulations
for the prevention of accidents must be complied with.
The representations within the Operating Instructions are not true to scale.
The dimensions given are not binding.
General indications of direction, such as FRONT, REAR, RIGHT, LEFT apply when view-
ing the front of the device.
5 Service and Maintenance....................................................................................... 23
5.1 Rollers .................................................................................................................. 23
6 Cleaning................................................................................................................... 24
7 Correspondence ..................................................................................................... 24
8 Repairs..................................................................................................................... 24

4
1.2 Responsibilities of the Operating Company
In compliance with the EC Directive 89/655/EEC, the operating company agrees to only
permit persons to work with the device who:
- are familiar with the basic regulations on industrial safety and accident prevention and
who have been trained in handling the device.
- have read and understood the chapter on safety and the warning notices in these
Operating Instructions and have confirmed this with their signatures.
- are examined regularly on their safe and conscientious working method.
1.3 Responsibilities of the Personnel
All persons who work with the device agree to perform the following duties before starting
work:
- to observe the basic regulations on industrial safety and accident prevention.
- to read the chapter on safety and the warning notices in these Operating Instructions and
to confirm with their signatures that they have understood them.
1.4 Informal Safety Measures
The Operating Instructions must always be kept on hand where the device is operated.
Apart from the Operating Instructions, the general and local applicable regulations on ac-
cident prevention and environmental protection must be provided and complied with.
1.5 Training of the Personnel
Only trained and instructed personnel is permitted to work with the device. The responsi-
bilities of the personnel must be clearly defined for mounting, commissioning, operation,
setup, maintenance, and repair. Trainees may only work with the device under the super-
vision of experienced personnel.
1.6 Intended Use
The device is intended exclusively to be used as a tension meter. Any other use or any
use exceeding this intention will be regarded as misuse. Under no circumstances shall
HANS SCHMIDT & Co GmbH be held liable for damage resulting from misuse.
The intended use also includes:
- Complying with all notices included in the Operating Instructions and observing all
inspection and maintenance works.
1.7 Dangers in Handling the Device
The device was designed according to the state of the art and the approved safety stan-
dards. Nevertheless, its use may cause serious or fatal injury to the user or third persons,
and/or an impairment of the device or of other material assets.
The device may only be applied:
- For its intended use in a faultless condition with regard to the safety requirements.
- Malfunctions that could impair safety must be remedied immediately.
- Personal protective equipment must be used according to the EC Directive 89/686/EEC.
The device must not be operated in potentially explosive areas and must not
come into contact with aggressive substances.

5
Model Measuring Range
daN
SCHMIDT
Calibration
KXE-20 0.5 - 20.0 fabric tape
KXE-50 0.5 - 50.0 fabric tape
1.8 Copyright
The copyright on these Operating Instructions remains with the company
HANS SCHMIDT & Co GmbH.
These Operating Instructions are intended for the operating company and its personnel
only. They contain instructions and notices that may only be reproduced on the prior writ-
ten permission of
HANS SCHMIDT & Co GmbH
and under indication of the complete reference data.
Violations will be prosecuted.
1.9 Declaration of Conformity, RoHs II and WEEE Registration
In compliance with the EU Directives 2004/108/EG and 2011/65/EU
HANS SCHMIDT & CO GmbH is registered in compliance with
the German Electrical and Electronic Equipment Act (ElektroG)
under WEEE Reg. No. DE 48092317.
2 Available Models
2.1 Specifications
Display Unit:
Calibration: According to SCHMIDT factory procedure
Units of Measure: daN
Accuracy: ± 1% FS* ± 1 digit (typically ± 0.5% FS*)
Overrange: 10% FS*, without accuracy guarantee
Overload Protection: 200% FS*
Measuring Principle: Strain gauge bridge
Signal Processing: Digital 24 bit A/D converter
Damping: Adjustable electronically (averaging)
Measuring Frequency: Approx. 1 kHz internally
Display Update Rate: 2x per second
Display: 4-digit LCD, height of digit 11 mm
Memory: Average, last value, MAX, MIN, MAX PEAK, MIN PEAK
Memory Modes: 4 - for up to 4000 readings
Temperature Coefficient: Gain: less than ± 0.01% FS*/°C
Analog Output Signal: 0 - 2 V DC (linearized) RLoad > 1 kW± approx.1%
(optional) Converter frequency 100 Hz
Digital Output Signal: USB
Temperature Range: 10 - 45 ° C
Air Humidity: 85% RH, max.
Auto Power Off: Automatically after approx. 3 min. of non-use
Power Supply: LiPo accumulator (approx. 60 h continous use, charging time
approx. 3.5 h)) and AC adapter 100 - 240 V AC
with 3 adapters (EU/USA/UK)
Housing Material: Aluminium profile with plastic outer casing (PVC)
Housing Dimensions: 197 mm x 58 mm x 47 mm (L x W x H)
Weight, net (gross): Approx. 340 g / 1250 g
*FS = Full Scale

6
2.1 Specifications (Cont.)
Sensor:
Measuring Rollers: 2x 22 mm ball bearing rollers
Width of Outer Rollers: 100 mm (ball bearing rollers)
Total Width of Rollers: 50 mm
Reference Frame Height Adjustment: 24 mm
Material: Anodized aluminium
Dimensions Reference Frame: 108 x 138 mm (L x W x H)
Weight, net (gross): 1000 g (1500 g)
2.2 Delivery Includes
Tension meter
1EK0662: USB cable
1K50202 AC adapter with 3 adapters (EU/USA/UK)
1SW-TI3: “TENSION INSPECT 3” software (Win XP or higher) for viewing and
storing the measured data on a PC.
1 Operating Instructions
1 Carrying case
2.3 Unpacking
Unpack the tension meter and inspect it for any shipping damage. Notices of defect must
be filed immediately, in writing, at the latest within 10 days on receipt of the goods.
3 Initial Setup and Operating Procedure
General information
This mobile electronic tension meter has been developed according to the system of the
INSTITUT TEXTILE DE FRANCE ITF. It allows measuring warp tensions of 50 mm wide
warps while the machine is running or at standstill.
It is a well-known fact that accurate thread tension data can only be obtained when mea-
suring a single end at a time using a stationary tension meter. The KXE model - System
ITF - however allows setting machines of the same make and type to comparable aver-
ages. The use of the same settings for several weaving machines improves product qual-
ity and throughput, and saves energy.
You can insert the SENSOR into the warp and remove it again while the machine is
running. The warp tension can be measured not only at the warp edges, but across the
whole width without causing excessive deflection of the ends. Four different values can
be displayed: Actual value, damped value, minimum value and maximum value. All
readings can be stored in the KXE memory and evaluated on a PC. The KXE can be
line- or battery-operated.

7
3.1 Notes Before Starting Measurement
Have you read and understood the Operating Instructions, in particular
Chapter 1 “Basic Safety Notices” ?
You are not permitted to operate the tension meter before doing so.
Before working with the instrument you must put on your personal protective
clothing, if necessary. For example, eye protectors, gloves, etc.
To avoid damage, do not move the center roller by hand.
Tensions that exceed the tension range of the instrument by more than 100%
may cause permanent damage to the measuring spring and must be avoided
under any circumstances.
3.1.1 ID Plate, CE Mark, Calibration Label
3.2 Operating Elements
Calibration label (option)
SCHMIDT Quality Seal
ID plate with CE mark and serial number
fig. 3.2
USB INTERFACE
HandleLever
DISPLAY MEM key RECALL / HOLD key
POWER / ZERO key
SENSOR
OUTER ROLLERS
DAMP key
MEASURING
ROLLER
The ID plate with the CE mark and the serial number as well as the calibration la-
bel (optional) are provided on the bottom of the display unit, the SCHMIDT Quality
Seal is provided on the surface.

8
3.3.2 Switch-On
Press the POWER key until all symbols are shown on the DISPLAY .
When you release the key, the DISPLAY momentarily shows the tension range and the
software version, e.g. E 1.0, followed by random values or “0.”
3.3.3 Switch-Off
Auto power off:
- The tension meter switches off automatically after 3 minutes of non-use.
Manual switch-off:
- Press the POWER key for five seconds.
3.3 Setup
The tension meter comes with a built-in rechargeable LiPo battery, which has been
charged at the factory. The tension meter can only be switched on if the battery is still
working, i.e. if the battery has enough charge. If the instrument does not power up or if
the battery level indicator shows only one bar after power-up (Chapter 3.3.2), the
battery needs to be recharged.
To ensure maximum battery life, avoid discharging it completely or charg-
ing it frequently for short periods. The battery should not be stored for a pro-
longed time when empty. After a maximum storage period of one year, the
battery has to be recharged.
3.3.1 Charging the Battery
The battery can only be charged at a temperature between +5 °C and +45 °C.
Before you connect the AC adapter, verify that the supply voltage is correct
(100 V - 240 V).
HANS SCHMIDT & Co. GmbH provides no warranty or liability for any
damage resulting from the use of AC adapters from other manufacturers.
To charge the battery, connect the cable of the AC adapter to the low USB output.
The battery can also be charged by connecting the USB cable to a PC.
When the battery is fully charged, the battery level indicator will show 3 bars .
The charging time is approx. 3 ½ hours.
Battery overcharging is not possible

9
When you shift the tension meter from the right to the left hand, you can rotate the
readings on the DISPLAY by 180°.
Measuring with the display unit in the left hand:
If you would like to use the left hand for measuring, you should reverse the readings on
the DISPLAY to make them easier to read.
Requirement:
Tension meter switched off as described in Chapter 3.3.2.
To reverse the display:
- Press and hold the DAMP and POWER
keys until the DISPLAY shows the rea
dings the other way around.
Measuring with the display unit in the
right hand:
Requirement:
Tension meter switched off as described in Chapter 3.3.2.
To restore the default orientation:
- Press and hold the DAMP and POWER
keys until the DISPLAY shows the rea
dings in the default orientation.
3.3.4 Reversing the Display
The selected display orientation remains stored in the KXE memory even after
the instrument is switched off.
fig. 3.3.4a
fig. 3.3.4b
3.3.5 Zero Adjustment of the Measuring Position
Before starting measurement you need to carry out zero adjustment, as
described below, each time the tension meter is switched on. This procedure is
necessary to compensate for the weight of the measuring roller in the measuring
position. The zero adjustment for the new measuring path only remains effective
until the instrument is switched off.
Zero adjustment must be repeated whenever the material path is changed or the
tension meter does not display “0.”
The process material must not yet be inserted!
Requirements:
- Tension meter switched on as described in Chapter 3.3.2.
To carry out zero adjustment:
- Holding the SENSOR at the HANDLE, place it in the desired measuring position.
Be careful to hold the instrument absolutely steady.
- Press the POWER key.
The DISPLAY momentarily shows
0 0 0 0
and then switches to .
The KXE is now adjusted for the new material path and is ready to measure.

10
Requirements:
- Tension meter switched on (Ch. 3.3.2).
- Damping factor set, if necessary (Ch. 3.4.2).
- Zero adjustment carried out (Ch. 3.3.5).
3.4 Operating Procedure
To insert the process material:
- Push the LEVER in the direction of the arrow to lift the REFERENCE FRAME and
the OUTER ROLLERS.
- Insert the MEASURING ROLLER into the warp.
- Push the LEVER back into the original position to move the REFERENCE FRAME
and the OUTER ROLLERS down again.
It is important to assure that the warp passes smoothly between the MEASURING
ROLLERS and the OUTER ROLLERS.
To measure the process material:
The DISPLAY now shows the measured tension values.
Error messages which might be displayed are described in Chapter 3.6.
To remove the process material:
- Push the LEVER in the direction of the arrow to lift the REFERENCE FRAME and
the OUTER ROLLERS.
- Remove the MEASURING ROLLER from the warp
LEVER
MEAS. ROLLER
OUTER ROLLERS
fig. 3.4
REFERENCE
FRAME
After removeing the process material, move the REFERENCE FRAME down
by using the leve, to protect the MEASURING ROLLER of damage.

11
3.4.1 Switching on Damping Mode
The KXE is equipped with an electronic damping which ensures steady readings when
tension fluctuates. This is achieved by averaging the measured values at the set update
rate.
Before switching on the damping mode, it is recommended that you measure the
first values without damping enabled.
Requirements:
- Process material inserted as described in Chapter 3.4.
- The DISPLAY has shown the first tension values.
To switch on damping:
- Press the DAMP key.
The DISPLAY shows the set damping factor.
- Release the DAMP key.
The DISPLAY shows DAMP below the currently measured value.
To switch off damping:
- Press the DAMP key.
The DISPLAY shows only the currently measured value.
3.4.2 Changing the Damping Factor
The tension meter is factory preset to a damping factor of 12. The tension values are
thereby averaged for the display in the following way:
12 old values + 4 new values
16
The damping factor can be modified in 15 steps from 01 = low damping:
1 old value + 15 new values
16
to 15 = high damping:
15 old values + 1 new value
16
Requirement:
- Tension meter switched on as described in Chapter 3.3.2.
To change the damping factor:
- Press and hold the DAMP key.
The DISPLAY shows the set damping factor.
You can now increase the damping factor with the MEM key and decrease it with
the RECALL key.
- Release the DAMP key.
The tension meter switches back to measuring mode.
The selected damping factor remains stored in the KXE memory even after the
instrument is switched off.

12
The tension meter features a data logger with a memory capacity for up to 4000 readings,
with which you can store different measuring periods at one or more machine positions.
The readings are saved 2x per sec-
ond, synchronously with the display
update rate, in all memory modes
except the “F” mode in which they
are saved 100x per second. All saved
readings and statistics can be shown
on the display or transmitted to a PC
(e.g. for further processing in Excel).
The memory can be allocated to dif-
ferent measuring periods, depending
on the memory mode.
3.5 Memory Modes
Memory Mode S C L F
Meas. periods,
max. 255 255 255 255
Readings, max. - 4000 4000 4000
Max. no. of read-
ings per position - Any 10 Any
Statistics Yes Yes Yes Yes
Save readings - Yes Yes Yes
The selected memory mode remains stored in the KXE memory even after the in-
strument is switched off.
Memory mode “S” STANDARD
(default):
The following values of a measuring
period are calculated and saved at a
rate of 2 readings per second:
Average value,
Last value,
Maximum value (MAX),
Minimum value (MIN),
Minimum peak value (MIN PEAK)
Maximum peak value (MAX PEAK)
Individual readings are not saved.
You can save up to 255 measuring
periods.
Memory mode “C” CONTINUOUS:
The following values of a measuring
period are calculated and all readings are
additionally saved at a rate of 2 readings
per second:
Average value,
Last value,
Maximum value (MAX),
Minimum value (MIN),
Minimum peak value (MIN PEAK)
Maximum peak value (MAX PEAK)
You can save up to 4000 readings, split
up into up to 255 measuring periods.
Memory mode “L” LIMIT:
The following values of a measuring period
are calculated and 10 readings are addition-
ally saved at a rate of 2 readings per second:
Average value,
Last value,
Maximum value (MAX),
Minimum value (MIN),
Minimum peak value (MIN PEAK)
Maximum peak value (MAX PEAK)
You can save up to 255 measuring periods
with 10 readings each.
Memory mode “F” FAST:
The following values of a measuring period
are calculated and all readings are additional-
ly saved at a rate of 100 readings per second:
Average value,
Last value,
Maximum value (MAX),
Minimum value (MIN),
Minimum peak value (MIN PEAK)
Maximum peak value (MAX PEAK)
You can save up to 4000 readings, split up
into up to 255 measuring periods.

13
3.5.1 Memory Mode Selection
Requirements:
- Tension meter switched on as described in Chapter 3.3.2.
- Memory cleared by simultaneously pressing the MEM and RECALL keys.
To select the memory mode:
- Press and hold the MEM key.
The DISPLAY shows S.
Press the DAMP or RECALL key to change the memory mode.
Memory mode “S” STANDARD (default):
The DISPLAY shows S.
The STANDARD memory mode is set.
Memory mode “C” CONTINUOUS:
If the DISPLAY shows C, the CONTINUOUS memory mode is set.
Memory mode “L” LIMIT:
If the DISPLAY shows L, the LIMIT memory mode is set.
Memory mode “F” FAST:
If the DISPLAY shows F, the FAST memory mode is set.
When you have selected the desired memory mode, you can release the MEM key.
The selected memory mode is now active and the tension meter switches back to
measuring mode.
The selected memory mode remains stored in the KXE memory even after the
instrument is switched off.

14
3.5.1.1 Data Logging in Mode “S” STANDARD
Requirements:
- Tension meter switched on as described in Chapter 3.3.2.
- Memory mode “S” STANDARD set as described in Chapter 3.5.1.
- Process material inserted as described in Chapter 3.4.
To save the first measuring period:
- Press and hold the MEM key until the
DISPLAY shows the memory mode “S” and the current memory number.
- Release the MEM key.
The tension meter starts logging the data.
While the tension data are stored, the MEM indicator blinks on the
DISPLAY and the currently measured value is displayed.
To stop data logging:
- When you want to end the measuring period, press the MEM key once again.
The statistical values are calculated from the logged tension data and stored in the
following order:
Average value,
Last value,
Maximum value (MAX),
Minimum value (MIN),
Minimum peak value (MIN PEAK),
Maximum peak value (MAX PEAK).
The MEM indicator stops blinking and remains on the display. The tension
meter shows the current reading and changes back to measuring mode.
To save the next measuring period:
- Press the MEM key again.
The DISPLAY shows the memory mode “S” and the next memory
number. You can save up to 255 measuring periods.
3.5.1.2 Data Logging in Mode “C” CONTINUOUS
Requirements:
- Tension meter switched on as described in Chapter 3.3.2.
- Memory mode “C” CONTINUOUS set as described in Chapter 3.5.1.
- Process material inserted as described in Chapter 3.4.
To save the first measuring period:
- Press and hold the MEM key until the
DISPLAY shows the memory mode “C” and the current memory number.
- Release the MEM key.
The tension meter starts logging the data.
While the tension data are stored, the MEM indicator blinks on the
DISPLAY and the currently measured value is displayed.
The logged tension values
remain stored in the KXE
memory even after the in-
strument is switched off.
The logged tension values
remain stored in the KXE
memory even after the in-
strument is switched off.

15
3.5.1.2 Data Logging in Mode “C” CONTINUOUS (Cont.)
To stop data logging:
- When you want to end the measuring period, press the MEM key once again.
The statistical values are calculated from the logged tension data and stored in the
following order:
Average value,
Last value,
Maximum value (MAX),
Minimum value (MIN),
Minimum peak value (MIN PEAK),
Maximum peak value (MAX PEAK).
Tension value - 1 -
Tension value - 2 -
↓
Tension value - N- (up to 4000 tension values in up to
255 measuring periods)
The MEM indicator stops blinking and remains on the display. The tension
meter shows the current reading and changes back to measuring mode.
To save the next measuring period:
- Press the MEM key again.
The DISPLAY shows the memory mode “C” and the next memory num-
ber. You can save up to 255 measuring periods with a total of 4000 readings max.
3.5.1.3 Data Logging in Mode “L” LIMIT
Requirements:
- Tension meter switched on as described in Chapter 3.3.2.
- Memory mode “L” LIMIT set as described in Chapter 3.5.1.
- Process material inserted as described in Chapter 3.4.
To save the first measuring period:
- Press and hold the MEM key until the
DISPLAY shows the memory mode “L” and the current memory number.
- Release the MEM key.
The tension meter starts logging the data.
While the tension data are stored, the MEM indicator blinks on the
DISPLAY and the currently measured value is displayed.
To stop data logging:
- When you want to end the measuring period, press the MEM key once again.
The statistical values are calculated from the logged tension data and stored in the
following order:
Average value,
Last value,
Maximum value (MAX),
Minimum value (MIN),
The logged tension values
remain stored in the KXE
memory even after the in-
strument is switched off.
The logged tension values
remain stored in the KXE
memory even after the in-
strument is switched off.

16
3.5.1.3 Data Logging in Mode “L” LIMIT (Cont.)
Minimum peak value (MIN PEAK),
Maximum peak value (MAX PEAK).
Tension value - 1 -
Tension value - 2 -
↓
Tension value - 10 - (up to 10 tension values in up to
255 measuring periods)
The MEM indicator stops blinking and remains on the display. The tension
meter shows the current reading and changes back to measuring mode.
To save the next measuring period:
- Press the MEM key again.
The DISPLAY shows the memory mode “L” and the next memory number.
You can save up to 255 measuring periods with up to 10 readings each.
3.5.1.4 Data Logging in Mode “F” FAST
Requirements:
- Tension meter switched on as described in Chapter 3.3.2.
- Memory mode “F” FAST set as described in Chapter 3.5.1.
- Process material inserted as described in Chapter 3.4.
To save the first measuring period:
- Press and hold the MEM key until the
DISPLAY shows the memory mode “F” and the current memory number.
- Release the MEM key.
The tension meter starts logging the data at a rate of 100 readings per second.
While the tension data are stored, the MEM indicator blinks on the
DISPLAY and the currently measured value is displayed.
To stop data logging:
- When you want to end the measuring period, press the MEM key once again.
The statistical values are calculated from the logged tension data and stored in the
following order:
Average value,
Last value,
Maximum value (MAX),
Minimum value (MIN),
Minimum peak value (MIN PEAK),
Maximum peak value (MAX PEAK).
Tension value - 1 -
Tension value - 2 -
↓
Tension value - N- (up to 4000 tension values in up to
255 measuring periods)
The logged tension values
remain stored in the KXE
memory even after the in-
strument is switched off.

17
3.5.1.4 Data Logging in Mode “F” FAST (Cont.)
The MEM indicator stops blinking and remains on the display. The tension
meter shows the current reading and changes back to measuring mode.
To save the next measuring period:
- Press the MEM key again.
The DISPLAY shows the memory mode “F” and the next memory num-
ber. You can save up to 255 measuring periods with a total of 4000 readings max.
3.5.2 Recalling the Stored Tension Values
With the TENSION INSPECT software from SCHMIDT, which is included with your
tension meter, you can easily and accurately evaluate the stored tension values and
export them to an Excel sheet.
3.5.2.1 Recalling the Stored Tension Values in Mode “S“ STANDARD
Requirement:
- Tension meter switched on as described in Chapter 3.3.2.
To recall the tension values:
- Press the RECALL key.
You can end recall any time by pressing the POWER key.
The DISPLAY blinks, showing the average value (AVG) of the first
measuring period (POS: 1) and the symbol.
- Press the RECALL key. The DISPLAY blinks, showing the
last value (LAST) of the measuring period.
- Press the RECALL key. The DISPLAY blinks, showing the
maximum value (MAX) of the measuring period and the symbol.
- Press the RECALL key. The DISPLAY blinks, showing the
minimum value (MIN) of the measuring period and the symbol.
- Press the RECALL key. The DISPLAY blinks, showing the
maximum peak value (PEAK MAX) of the measuring period, the PEAK indicator
Memory Mode STANDARD ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒
Pos: 1 Pos: 2 Pos: 3 Pos: 4
AVG: 22.0 AVG: 12.0 AVG: 12.0 AVG: 12.0
Last: 23.0 Last: 22.1 Last: 22.1 Last: 22.1
MAX: 24.0 MAX: 22.1 MAX: 22.1 MAX: 22.1
MIN: 21.0 MIN: 5.4 MIN: 5.4 MIN: 5.4
PEAK MAX: 26.0 PEAK MAX: 28.1 PEAK MAX: 28.1 PEAK MAX: 28.1
PEAK MIN: 19.0 PEAK MIN: 1.8 PEAK MIN: 1.8 PEAK MIN: 1.8
Peak
Peak

18
3.5.2.1 Recalling the Stored Tension Values in Mode “S“ STANDARD (Cont.)
and the symbol.
- Press the RECALL key. The DISPLAY blinks, showing the
minimum peak value (PEAK MIN) of the measuring period, the PEAK indicator
and the symbol.
- Press the RECALL key.
The next measuring period (POS: 2) is shown on the DISPLAY, starting with the
average value (AVG).
3.5.2.2 Recalling the Stored Tension Values in Mode “C“ CONTINUOUS
Requirement:
- Tension meter switched on as described in Chapter 3.3.2.
To recall the tension values:
- Press the RECALL key.
You can end recall any time by pressing the POWER key.
The DISPLAY blinks, showing the average value (AVG) of the first
measuring period (POS: 1) and the symbol.
- Press the RECALL key. The DISPLAY blinks, showing the
last value (LAST) of the measuring period.
- Press the RECALL key. The DISPLAY blinks, showing the
maximum value (MAX) of the measuring period and the symbol.
- Press the RECALL key. The DISPLAY blinks, showing the
minimum value (MIN) of the measuring period and the symbol.
Memory Mode CONTINUOUS ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒
Pos: 1 Pos: 2 Pos: 3 Pos: 4
AVG: 22.0 AVG: 12.0 AVG: 12.0 AVG: 12.0
Last: 23.0 Last: 22.1 Last: 22.1 Last: 22.1
MAX: 24.0 MAX: 22.1 MAX: 22.1 MAX: 22.1
MIN: 21.0 MIN: 5.4 MIN: 5.4 MIN: 5.4
PEAK MAX: 26.0 PEAK MAX: 28.1 PEAK MAX: 28.1 PEAK MAX: 28.1
PEAK MIN: 19.0 PEAK MIN: 1.8 PEAK MIN: 1.8 PEAK MIN: 1.8
10.8 14.2 14.1 15.4
10.0 19.4 11.2 18.3
7.3 22.9 8.9 17.5
6.1 17.3 10.2 7.8
⇓⇓⇓⇓
nnnn
Peak
Peak

19
3.5.2.2 Recalling the Stored Tension Values in Mode “C“ CONTINUOUS (Cont.)
- Press the RECALL key. The DISPLAY blinks, showing the
maximum peak value (PEAK MAX) of the measuring period, the PEAK indicator
and the symbol.
- Press the RECALL key. The DISPLAY blinks, showing the
minimum peak value (PEAK MIN) of the measuring period, the PEAK indicator
and the symbol.
- Press the RECALL key. The measured values no. 1 — n of the first measuring period
can be recalled.
- Press the RECALL key.
The next measuring period (POS: 2) is shown on the DISPLAY, starting with the
average value (AVG).
3.5.2.3 Recalling the Stored Tension Values in Mode “L“ LIMIT
Requirement:
- Tension meter switched on as described in Chapter 3.3.2.
To recall the tension values:
- Press the RECALL key.
You can end recall any time by pressing the POWER key.
The DISPLAY blinks, showing the average value (AVG) of the first
measuring period (POS: 1) and the symbol.
- Press the RECALL key. The DISPLAY blinks, showing the
last value (LAST) of the measuring period.
- Press the RECALL key. The DISPLAY blinks, showing the
Memory Mode LIMIT ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒
Pos: 1 Pos: 2 Pos: 3 Pos: 4
AVG: 22.0 AVG: 12.0 AVG: 12.0 AVG: 12.0
Last: 23.0 Last: 22.1 Last: 22.1 Last: 22.1
MAX: 24.0 MAX: 22.1 MAX: 22.1 MAX: 22.1
MIN: 21.0 MIN: 5.4 MIN: 5.4 MIN: 5.4
PEAK MAX: 26.0 PEAK MAX: 28.1 PEAK MAX: 28.1 PEAK MAX: 28.1
PEAK MIN: 19.0 PEAK MIN: 1.8 PEAK MIN: 1.8 PEAK MIN: 1.8
10.8 14.2 14.1 15.4
10.0 19.4 11.2 18.3
7.3 22.9 8.9 17.5
6.1 17.3 10.2 7.8
⇓⇓⇓⇓
n 10 10 10
Peak
Peak

20
3.5.2.3 Recalling the Stored Tension Values in Mode “L“ LIMIT (Cont.)
maximum value (MAX) of the measuring period and the symbol.
- Press the RECALL key. The DISPLAY blinks, showing the
minimum value (MIN) of the measuring period and the symbol.
- Press the RECALL key. The DISPLAY blinks, showing the
maximum peak value (PEAK MAX) of the measuring period, the PEAK indicator
and the symbol.
- Press the RECALL key. The DISPLAY blinks, showing the
minimum peak value (PEAK MIN) of the measuring period, the PEAK indicator
and the symbol.
- Press the RECALL key. The measured values no. 1 — 10 of the first measuring
period can be recalled.
- Press the RECALL key.
The next measuring period (POS: 2) is shown on the DISPLAY, starting with the
average value (AVG).
3.5.2.4 Recalling the Stored Tension Values in Mode “F“ FAST
Requirement:
- Tension meter switched on as described in Chapter 3.3.2.
To recall the tension values:
- Press the RECALL key.
You can end recall any time by pressing the POWER key.
The DISPLAY blinks, showing the average value (AVG) of the first
Memory Mode FAST ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒
Pos: 1 Pos: 2 Pos: 3 Pos: 4
AVG: 22.0 AVG: 12.0 AVG: 12.0 AVG: 12.0
Last: 23.0 Last: 22.1 Last: 22.1 Last: 22.1
MAX: 24.0 MAX: 22.1 MAX: 22.1 MAX: 22.1
MIN: 21.0 MIN: 5.4 MIN: 5.4 MIN: 5.4
PEAK MAX: 26.0 PEAK MAX: 28.1 PEAK MAX: 28.1 PEAK MAX: 28.1
PEAK MIN: 19.0 PEAK MIN: 1.8 PEAK MIN: 1.8 PEAK MIN: 1.8
10.8 14.2 14.1 15.4
10.0 19.4 11.2 18.3
7.3 22.9 8.9 17.5
6.1 17.3 10.2 7.8
⇓⇓⇓⇓
nnnn
Peak
Peak