Elmo VILLEGGIO User manual

Hybrid Multifunctional Control Units
for Intrusion Detection Systems
VILLEGGIO©
USER MANUAL
090060699

2
VILLEGGIO - USER MANUAL - 090060699
FOREWORD
FOR INSTALLERS
Please follow carefully the specifications about electric and security systems realization further to the manufacturer’s
prescriptions indicated in the manual provided.
Provide the user the necessary indication for use and system’s limitations, specifying that there exist precise
specifications and different safety performance levels that should be proportioned to the user needs. Have the user
read carefully the instructions provided in this document.
FOR USERS
Carefully check the system functionality at regular intervals making sure all enabling and disabling operations were
made correctly.
Have skilled personnel make the periodic system’s maintenance. Contact the installer to verify correct system oper-
ation in case its conditions have changed (e.g.: variations in the areas to protect due to extension, change of the ac-
cess modes, etc.)
......................................................
This device has been designed, assembled and tested with the maximum care, adopting control procedures in
accordance with the laws in force. The full correspondence to the functional characteristics is given exclusively when
it is used for the purpose it was projected for, which is as follows:
Hybrid Multifunctional Control Units for Intrusion Detection Systems
Any use other than the one mentioned above has not been forecasted and therefore it is not possible to guarantee
the correct functioning of the device. Similarly, any other use of this technical manual other than the one it has been
compiled for - that is: to illustrate the devices technical features and operating mode - is expressly prohibited.
The manufacturing process is carefully controlled in order to prevent defaults and bad functioning. Nevertheless, an
extremely low percentage of the components used is subjected to faults just as any other electronic or mechanic prod-
uct. As this item is meant to protect both property and people, we invite the user to proportion the level of protection
that the system offers to the actual risk (also taking into account the possibility that the system was operated in a de-
graded manner because of faults and the like), as well reminding that there are precise laws for the design and as-
semblage of the systems destinated to these kind of applications.
The system’s operator is hereby advised to see regularly to the periodic maintenance of the system, at least
in accordance with the provisions of current legislation, as well as to carry out checks on the correct running
of said system on as regular a basis as the risk involved requires, with particular reference to the control unit,
sensors, sounders, dialler(s) and any other device connected. The user must let the installer know how well
the system seems to be operating, based on the results of periodic checks, without delay.
Design, installation and servicing of systems which include this product, should be made by skilled staff with the nec-
essary knowledge to operate in safe conditions in order to prevent accidents. These systems’ installation must be
made in accordance with the laws in force. Some equipment’s inner parts are connected to electric main and therefore
electrocution may occur if servicing was made before switching off the main and emergency power. Some products
incorporate rechargeable or non rechargeable batteries as emergency power supply. Their wrong connection may
damage the product, properties and the operator’s safety (burst and fire).
YOUR DEALER:

3
090060699 - USER MANUAL - VILLEGGIO
1. GENERALS
VILLEGGIO is a microprocessor-based control unit designed to realize high-performance intrusion detec-
tion systems with the following special features (according to the model in use):
• Advanced electronic components and circuits.
• Advanced design.
• Low-profile plastic housing with the possibility of flush mount.
• Possibility to install VILLEGGIO on to walls or brickwalls using the optional accessory IBOX.
• Optional side flanges available in various colours for a stylish personalization.
• Optional plug-in modules to increase VILLEGGIO operating functions.
• Built-in chrothermostat with boiler failure detection and SMS-based remote control.
• Two different models available, VIBASIC and VIDOMO, to meet all onfiguration and performance
level requirements.
• Expansion wired/wireless modules to increase VILLEGGIO operating capacity.
• Support of control devices connected over RS485 serial line (VIDOMO.)
• Expandable with concentrators connected over RS485 serial line (VIDOMO.)
• Exceptional flexibility when configured from a PC.
• Operating flexibility with remote commands.
• Suitable for mobile applications (camper vans, watercrafts, etc.)
• Suitable for standard (i.e. non-mobile) applications (houses, offices, etc.)
• Considerable energy saving due to the extremely low mains and battery consumption.
• Compliant with EN50131 standard.
• VILLEGGIO is an EL.MO. S.p.a. registered trademark.
NOTE: in this manual AREA stands for ’a group of sectors’ and SECTOR (also PARTITION) stands
for ’a group of detectors/zones’.
2. BLOCK DIAGRAMS OF VILLEGGIO SYSTEM
Operating diagram:

4
VILLEGGIO - USER MANUAL - 090060699
VIDOMO operating diagram:
VIBASIC operating diagram:
UP TO 64 WIRED / WIRELESS ZONES
8/16 WIRED ZONES
ONBOARD
48 TO 64 WIRELESS ZONES ACCORDING TO
THE AMOUNT OF WIRED ZONES SET
8/16 WIRED ZONES
ONBOARD

5
090060699 - USER MANUAL - VILLEGGIO
Operating diagram with wireless devices:
TYR
O
S
MED
I
CAL
REM
O
TE
C
O
NTR
O
L
AM MDEREN AED
Rs
F
W
.
4
.
x
O
R
A
B
O
V
E
V
I
LLE
GGIO
SER
I
ES
UN
I
TS
V
I
BAS
I
C
V
I
D
OMO
MODELS
AND
T
E
R
M
I
N
A
L
B
O
A
R
D
F
O
R
8
W
I
R
E
D
Z
O
N
E
S
C
O
N
F
I
G
U
R
A
T
I
O
N
O
P
T
I
O
N
S
:
D
O
U
B
L
E
B
A
L
A
N
C
E
D
,
T
R
I
P
L
E
B
A
L
A
N
C
E
D
.
N
O
,
N
C
,
F
A
S
T
.
U
P
T
O
1
6
Z
O
N
E
S
W
I
T
H
S
P
L
I
T
A
N
D
E
X
T
E
N
D
E
D
S
P
L
I
T
F
U
N
C
T
I
O
N
S
.
P
H
O
N
E
L
I
N
E
F
O
R
-
D
I
G
I
T
A
L
D
A
T
A
T
R
A
N
S
M
I
S
S
I
O
N
S
-
V
O
I
C
E
D
A
T
A
T
R
A
N
S
M
I
S
S
I
O
N
S
W
I
T
H
V
O
I
C
E
S
Y
N
T
H
E
S
I
S
-
R
E
M
O
T
E
A
S
S
I
S
T
A
N
C
E
M
I
N
I
D
I
N
AND
M
I
N
I
US
B
C
O
N
N
E
C
T
O
R
S
F
O
R
SETUP
FR
O
M
P
C
A
N
D
F
I
RM
W
ARE
U
P
D
A
T
E
C-NO-NC RELAY OUTPUT FOR
INTRUSIONALARM.

6
VILLEGGIO - USER MANUAL - 090060699
3. USER INTERFACE
3.1 View of VILLEGGIO front panel
3.2 Display LCD
Backlight status; automatic switch off after one minute.
Note: backlight operating mode can be modified using software application.
Users can select two operating modes: STANDARD (as seen above, switch off after 1 minute), and
USER-DEFINED, with colours defined by users via software for activity / inactivity status (for inactivity
status set a very low light level for power saving.)
In case of mains failure while user is inactive, display backlight turns off to save battery charge. In
some cases it is possible to use the emergency light (see “Emergency light” on page 37.)
GREEN backlight.
Standard operating status before the display turns off for
power saving.
RED backlight.
Exit time mode or armed panel / areas / sectors status.
Backlight will turn on also when user is not operating,
during codes or commands digitation or when using a
proxy key.
Area with tiny holes for built-in siren sound output.
This area also contains microphone and loud-
speaker for
voice syn-
thesis and
remote liste-
ning func-
tions.
LCD Display with RGB
backlight.
RED -> armed status
and user activity.
GREEN -> disarmed
status. Normally display
backlight is off.
System and alarm LED
indicators.
Sector keys S1, S2, S3,
S4. Central area with
proxy key reader.
Rubber keypad with
protection cover.
Panel case
side flange.
It can be re-
placed with
others with
different co-
lours.

7
090060699 - USER MANUAL - VILLEGGIO
3.3 Panel display standard information
The top row of the display, the "icons area" shows the following indications:
- The indication of the RF signal will be showed only in case of a valid transmission. Normally, the signal
intensity, indicated by bars, will not be showed. According to their number, bars indicate signal level:
RF signals are generated by wireless devices of HELIOS series (and compatible.)
The indication may refer to other devices operating over the same frequency but not registered.
- The indication of power supply status refers to the presence of power supply unit; next to the battery icon,
"OK" indicates that there are no anomalies, while a blinking "NO" indicates that there are power anomalies.
- Icon with the circled plus (+) sign will be displayed only with GPS module installed; next to the "+" icon,
"OK" indicates no anomalies, while a blinking "NO" indicates that there are GPS anomalies.
- Telephone icon will be displayed only with PSTN interface module installed; next to the icon, "OK" indica-
tes no anomalies, while a blinking "NO" indicates that there are PSTN anomalies.
- Antenna icon will be displayed only with GSM module installed and properly register to the mobile network.
Bars next to the icon indicate the level of GSM signal received. When the bars are not visible, it means
that there are no registered GSM modules.
The display also shows the temperature detected; such indication will blink when the temperature has to be
calibrated. Calibration can be performed using both user and installer menus. For calibration procedure, see
relevant chapter.
The drawing above illustrates the use of the optional remote temperature module MDTEMP. The module
can be installed wherever necessary. The display of the temperature detected by the panel built-in sensor can
be set as primary or secondary as to the one detected by the radio sensor; the position of the two values on
the display can be changed, as well illustrated above.
In ordert to avoid confusion, the temperature detected by the panel built-in sensor can be hidden using the
panel software.
Information about week days, date, and time can be set using both user and installer menus.
The display also indicates panel different operating modes by changing backlight colour. According to
EN50131 standard, such indications can be hidden (for further information, please see relevant chapter.)
Display welcome messagecan be defined via software application. Bydefault the field shows no messages.
One bar = poor Two bars = weak Three bars = good Four bars = excellent
RF SIGNAL
RECEIVED
POWER SUPPLY GPS PSTN
GSM SIGNAL
DATE
HOURS AND MINUTES
WEEK DAY
TEMPERATURE
DETECTED
BRAND MODEL
OPERATING STATUS
WELCOME
MESSAGE
THE TWO VALUES WILL BE
DISPLAYED WHEN OPTIONAL
MODULE MDTEMP IS INSTALLED
TEMPERATURE
DETECTED BY
MDTEMP
TEMPERATURE
DETECTED BY
UNIT BUILT-IN
SENSOR
NOTE:
by default the
temperature
detected by
the module will
be displayed
on the right
and the one
detected by
the internal
sensor on the
left. Such posi-
tions can be
inverted via
software.

8
VILLEGGIO - USER MANUAL - 090060699
3.4 Information displayed with active chronothermostat
VILLEGGIO panel allows to control boiler operating mode; its chronothermostat function can work on daily
or weekly schedules and is able to detect boiler failures. If a GSM module has been installed (MDGSMI or MD-
SGME, optional) it will be possible to send and receive control SMS texts.
Note: unit’s display shows 24-hour time schedule for the three temperature time intervals / levels:
-->> level 1 (F1) indicates the highest temperature, level 3 (F3) the lowest.
Small squares indicate level 1 or level 2; lines indicate level 3.
’Antifreeze level’ is not displayed.
Note: The drawing above illustrates the use of the optional remote temperature module MDTEMP. The mo-
dule can be installed wherever necessary. In order to avoid confusion, the temperature detected by
the panel built-in sensor can be hidden using the panel software.
Note: The display of the temperature detected by the panel built-in sensor can be set as primary or secon-
dary as to the one detected by the radio sensor; the position of the two values on the display can be
changed, as illustrated above.
For operating details, please see “Chronothermostat function” on page 32.
BOILER ON
1
2
TIME
SCHEDULES
BLINKING IF BOILER
IS BLOCKED
TEMPORARY
CHANGE
( = INCREASE = DECREASE)
TEMPERATURE
TEMPERATURE DETECTED
THE DOUBLE DISPLAY REFERS
TO THE INSTALLATION OF MDTEMP
OPTIONAL MODULE
TEMPERATURE
DETECTED
BY MDTEMP
TEMPERATURE
DETECTED BY
PANEL BUILT-IN
SENSOR

9
090060699 - USER MANUAL - VILLEGGIO
3.5 Panel status icons
= Indicates panel arming condition:
ON = No zones in alarm and/or tamper condition.
OFF = Alarmed zone(s) not belonging to the exit path.
SLOW Blinking = Exit path zones in anomaly condition with disarmed panel OR zone(s) in alarm/
tamper condition generating events different from ’intrusion alarms’.
= Indicates panel operating status:
ON = Normal operating status. please see note below.
SLOW Blinking = System anomaly (Mains failure, Discharged battery, Open tamper contact,
or anomaly memories, Fault, RF Anomaly, etc.), zones anomaly.
Note: when properly programmed via software, LED indicator will remain OFF when there are
no anomalies (System Options > Power Saving > Yellow LED off when there are no anoma-
lies menu.)
= General alarm memory:
OFF = No active alarms.
ON = Intrusion alarm cycle (Relay enabled.)
SLOW Blinking = Presence of intrusion memories.
= Tamper memories:
OFF = No zones in tamper condition.
ON = Tamper alarms cycle active (Relay enabled.)
SLOW Blinking = Tamper alarm(s) logged.
FAST Blinking (for all four indicators) = during configuration from keypad.
3.6 ’S’ keys function
Sector keys S1, S2, S3, S4 are used to arm/disarm corresponding sector(s);
during configuration procedure keypad backlight remains ON.
’S’ keys backlight ON indicates that the corresponding sector is armed; backli-
ght OFF indicates that the sector is disarmed.
’S’ keys blink slowly during exit time, quickly in case of Max Security arming.
REDGREEN YELLOW

10
VILLEGGIO - USER MANUAL - 090060699
3.7 Keypad operating mode
3.8 Information on the display
Press and keys to enter the control menu for:
- system anomalies status,
- zones anomaly status,
- alarm memories,
- tamper memories.
Arrow keys allow to browse menus; to enter menus press OK key, in case of multiple anomalies use and
keys to browse messages to display.
To exit menus, use STOP key.
Zones not in idle status will be displayed and identified with the name assigned during panel configuration
(ex. Kitchen window, hall IR, etc.)
Panel operating status will be indicated by the icons: , , , .
Normal operating mode will be resumed after one minute from last key pressed.
Note: when the ’visualization protection’ function is active (EN 50131 compliance) and has been enabled
via software application, the menus cannot be browsed directly with and keys: in such case,
the authentication as USER is required by digiting the 6-digit user code and then the arrow keys,
or . Information provided refers only to pertaining area.
STOP, ,, *, #and OK keys are used:
- to display anomalies;
- to browse menus;
- to select / deselect items;
- to save selections made;
- to exit panel menus.
0and 1keys have also an alphabetic function during
panel configuration.
IMPORTANT: if you press *and # keys
simultaneously, this will generate a "Panic alarm" event
indicating also the keypad that detected such event.
IMPORTANT
VILLEGGIO panel can be configured according to EN50131 standard or according to CEI 79-2 stan-
dard and the operating indications will be displayed accordingly.
This manual will illustrate the two procedures separately.
When the panel is armed after a configuration based on EN50131 standard with the ’visualization
protection’ function active, system and alarm LED indicators on the front cover and ’icons row’ on
the panel display will remain off. Only sector keys (S1, S2, etc.) and remote readers relevant LED
will be on according to system status. Readers indication can be disabled via software (System Op-
tions > Power Saving > Reader arming LED OFF when inactive menu): reader LED will switch off
after one minute from the last command received together with LCD display backlight.

11
090060699 - USER MANUAL - VILLEGGIO
In case of GPS module installation, its operating status can be controlled via the system menu on "GPS
Status" page from the panel keypad.
Example:
3.9 Acoustic signals for zones anomaly condition (Din-don)
For special requirements, the panel can be set to emita single or continuous beep sound when one or more
zone(s) enter(s) an anomaly condition.
4. OPERATING MODE
Note: VIDOMO unit can be connected to remote control devices installed according to users’ needs.
For such purpose, users can adopt touch screen keypads (TATTILO) or traditional keypads (NIRVA,
MIDAS), flush-mount control devices (ETR-ZENITH and IZENITH), addressed readers (I8.)
System test, Chronothermostat, Temperature information and Installer access menus are available
from built-in keypad only.
4.1 Panel disarming with user code
WARNING: when a user code is modified (increased or diminished) by one unit during digi-
tation (i.e. instead of 9, 0 or 8 are digited), this will disarm the panel and generate a DURESS
alarm; such alarm will be managed via telephone dialler or GSM module.
For operating details, see “Maximum security function control” on page 21.
The distance value can
be hidden bye the instal-
ler via panel software.
DO ALLARMED
SECTORS BELONG
TO THE USER?
YES
NO
SECTORS NOT
ASSIGNED TO THE
USER WILL
REMAIN ARMED EXAMPLE

12
VILLEGGIO - USER MANUAL - 090060699
4.2 Panel arming with user code
Note: if one of selected sectors is not available for arming, none of the selected sectors will be armed (nei-
ther those assigned to different areas.)
4.3 Panel disarming with proximity keys
Note: when panel areas and/or sectors have been armed with ’Max Security’ option, they cannot be disar-
med by users without ’Max Security’ property.
4.4 Panel arming with proximity keys
Note: such procedure cannot be used for total arm/disarm with ’Max Security’ option.
4.5 Panel partial arming with proximity keys - #1
VILLEGGIO control unit can also be armed partially.
After having presented the proximity key to the sensitive areas users shall select the desired sector keys
within 5 secs.
SELECTION OF
SECTORS TO BE
ARMED
(S1, S2, S3, S4 KEYS
WILL BE BLINKING)
TIME INTERVAL CADENCED
BY THE BUILT-IN BUZZER
YES
S2 S3
S1
S4
OR WAIT
AROUND 4s
FOR TOTAL
ARMING
FOR
PARTIAL
ARMING
EXAMPLE OF
TOTALARMING
EXAMPLE OF
PARTIAL ARMING
KEYPAD BACKLIGHT WILL
TURN OFF AFTER 1MIN
S2 S3
S1
S4
WAIT A FEW SECS
FOR SECTOR KEYS
TO TURN OFF ACOUSTIC
CONFIRMATION
S2 S3
S1
S4
S2 S3
S1
S4
EXIT TIMEACTIVE AND
INDICATED BY THE CADENCED BEEPING
OF THE BUILT-IN BUZZER OF
THE CONTROL UNIT, KEYPADS AND
REMOTE CONTROL POINTS
S2 S3
S1
S4
WAIT A FEW SECS
FOR SECTOR KEYS
TO TURN OFF

13
090060699 - USER MANUAL - VILLEGGIO
4.6 Panel partial arming with proximity keys - #2
To proceed with this function, enable partial arming function in Users -> User X - User Options -> Enable
proxy key for unit partitioning software menu.
In the following example, the user can access Area 1 with S1 and S2 as proposed sectors and S1, S2, S3,
and S4 as authorized sectors.
Note: if you think the procedure too complicated, require M4 proximity keys of various colours and have
them configured differently:
Black key = Total arm/disarm Yellow key = Sectors S1 and S2 Red key = sectors S3 and S4
4.7 Arming block
To comply with EN50131 standard this function shall be activated. It will have the following effects:
- If phone dialler and system sirens fail simultaneously, the system cannot be armed.
- If a radio detector or siren have not been supervised, the system cannot be armed.
- When exit time has expired, the system cannot be armed if a zone included in exit path is alarmed. In such
conditions, the Arming Failure event will be generated and radio sirens will flash signalling unit disarmed
status.
DEFAULT: disabled.
Note: in case of ’no supervision’ the system will not be armed only if the detector or siren are currently in
such condition, but it will be armed normally if a ’no supervision’ event has been logged on system memory and
afterwards the detector or siren have restored the normal communication with the unit.
4.8 Forced arming
Incasethesystem could not be armedbecauseof dialleror sirens fault or because of ’no supervision’event,
system arming can be forced.
The unit display (and keypads display in case of VIDOMO unit) of areas/sectors included will show the fol-
lowing message:
FAULT
FORCE ARMING?
ONE LED
BLINKING
PRESENT THE KEY
TO THE SENSITIVE AREA
TWO LEDs
BLINKING
ONE LED
BLINKING
PRESENT THE KEY
TO THE SENSITIVE AREA
PRESENT THE KEY
TO THE SENSITIVE AREA

14
VILLEGGIO - USER MANUAL - 090060699
The message will be displayed for 15 seconds during which the arming of system can be forced as fol-
lows:
- with code on keypad: press OK.
- with M4 key: present M4 key or press OK on the keypad to which the reader is
connected.
- with remote control device: activate remote control again.
Note: in case of arming denied and forced arming with M4 key, the red LED will blink fast during arming
procedure to indicate the forced command (in case of partial arming from I66 reader connected to
the onboard keypad, yellow LED will blink as well.)
4.9 Automatic forced arming
Forced arming becomes automatic in case of fault or ’no supervision’ event under the following conditions:
- system armed remotely via software application,
- system armed by system timer,
- system armed via SMS text.
4.10 Automatic forced arming denied
Automatic force arming will be denied in case of detector(s) in anomaly condition.
In such case, if the arming command was sent via SMS, the unit will promptly reply with the following mes-
sage: < DISARMING DENIED >
4.11 Fast arming
This function allows to arm the unit without using a key or the user code.
For a sector fast arm follow the instructions in the following drawing:
NOTE: If a different sector key is pressed during the procedure, the armed sector will be modified.
If the fast arming is not confirmed with OK key, the procedure will be cancelled after 5 seconds.
Fast arming can be activated only for sectors not armed and not being armed; in addition, sectors must have
been associated to at least one user.
If you press the key of a sector that cannot be armed during the fast arming procedure, the procedure will
be stopped.
CONFIRM
THE COMMAND
EXIT TIME WILLACTIVATE AND WILL
BE INDICATED BY THE CADENCED
BEEPING OF KEYPADS AT THE
REMOTE CONTROL SITES
PRESS THE KEY OF THE SECTOR TO BE
ARMED IN FAST MODE.
THE KEY WILL START BLINKING

15
090060699 - USER MANUAL - VILLEGGIO
If the suitable option is enabled, fast arming procedure can be executed by pressing twice the sector key,
so it will be possible to use also ETRZENITH and IZENITH flush-mount key points.
4.12 Arm command from external control device
For special operating requirements, the panel can be set to accept arm/disarm commands from a control
device different from compatible keypads/proxy keys/remote controls.
Such control device shall have the same performance level of the panel and will have to be wired to one of
panel zones and setup for the total/partial command required.
4.13 Display panel operating status on I66 readers
I66 readers properly connected to VILLEGGIO units can provide the following information:


16
VILLEGGIO - USER MANUAL - 090060699
4.14 Display advanced options
4.14.1 Display partial arming on readers
4.14.2 Display armed sectors on reader
This function allows to display control unit sectors partial armed status that will be signalled by the external
reader LED indicator (e.g. I66.)
Note: not available if VILLEGGIO keypad has been set as ’system keypad’.
Not available in case of total arm/disarm with ’Max Security’ option.
To activate armed sectors status display, select both Display partial arming on reader and Display armed
sectors on reader in AREAS menu.
The reader LED will provide the following indications:
4.14.3 General indications for armed/disarmed status with PASSLIGHT
Passlight indicator can be used only to signal panel status.
It must be setup as the I8 reader and used alone or with other I8 readers.
PASSLIGHT indications:
- Light GREEN + FIXED = no sectors associated to the reader is armed.
- Light RED + SLOW BLINKING = when at least one sector associated to the reader with exit time activated.
- Light RED + FIXED = when at least one sector associated to the reader is armed.
Passlight does not discriminate between standard and max security arming.
VILLEGGIO gives the possibility to activate partial arming status di-
splay that will be signalled by the external reader LED indicator (e.g.
I66.)
To activate this function, select Display partial arming on reader in
AREAS menu.
Note: this display option is alternative to Display armed sectors
on reader option. The LED indicator will blink quickly in case of
partial/total arming in Max Security mode.
LED will blink differently for each sector to display.
One blink = sector S1. Two blinks = sector S2.
Three blinks = sector S3. Four blinks = sector S4.
Example:
Partial arming: sectors S1 and S3 armed = 1 blink + pause + 3 blinks in sequence.
All area sectors armed (S1, S2, S3, S4) = 1 blink + pause + 2 blinks +pause + 3 blinks
+ pause + 4 blinks.
SLOW
BLINKING

17
090060699 - USER MANUAL - VILLEGGIO
Comparison of PASSLIGHT and I8 reader indications:
4.15 Panel arm/disarm signalled via siren strobe
The function has to be activated via software and allows to signal panel arm / disarm with suitable optical-
acoustic signals generated by the wired siren(s).
The operating mode is similar to that of vehicles alarm systems: the external siren strobe will flash once in
case of panel arming, twice in case of panel disarming and the siren will also emit acoustic signals accordingly
and simultaneously.
4.16 Use of remote control devices
4.16.1 ATLANTE 4
Users can arm/disarm VILLEGGIO panel partially/totally by using a compatible remote control such as
ATLANTE4. The remote control device use is managed by the panel application; remote control keys and LED
operate as illustrated in the following diagram:
Note: if one of selected sectors is not available for arming, none of the selected sectors will be armed (nei-
ther those assigned to different areas.) Remote control device and proximity key cannot be used si-
multaneously, only alternatively. The remote control device cannot be used for partial/total
arming in Max Security mode.
NOTE: IF NECESSARY, THE CONTROL UNIT STATUS
INDICATION CAN BE DEACTIVATED USING READER DIP 8.
SUCH SETTING DOES NOTAFFECT THE INDICATOR.

18
VILLEGGIO - USER MANUAL - 090060699
4.16.2 ATLANTE4PLUS
ATLANTE4PLUS device is a bidirectional control device; it is equipped with 6 backlit yellow keys plus a cen-
tral two-colour LED (green/red) for operating indications. Under the rubber keys, the yellow LEDs light on to
confirm the reception and execution of the commands. The central LED indicates with the green light the device
activation caused by the pressure of a key, with the red light the impossibility to perfom the command or the
missed confirm of the command reception.
Note: in case of impossibility to perfom the command or missed confirm of the command reception the LED
light will be red. In case of impossibility to perfom the command (ex. arming command with panel not ready to
be armed) the red LED lights on within few seconds; in case of missed confirm of the command reception, the
red LED lights on after 10 seconds.
Remote control device and proximity key cannot be used simultaneously, only alternatively.
The remote control device cannot be used for partial/total arming in Max Security mode.
4.16.3 ATLANTE6

19
090060699 - USER MANUAL - VILLEGGIO
4.16.4 ATLANTE6C
Simplified arming with 6-key ATLANTE6C remote control device.
One of the typical use of VILLEGGIO unit is for boats protection. It is quite common, in such applications,
to find boat ladder control systems remotely controllable from the quay. In case of EL.MO. ladder protection
systems such as CARABOTTINO, users can use the two central keys of ATLANTE6C remote control device
to simply arm/disarm VILLEGGIO unit.
4.17 Remote partial arming
VILLEGGIO panel can be armed/disarmed either totally or partially from a remote location by using special
software applications.
4.18 Zones set as EXIT PORT
The panel can be armed by users when they are inside the premises and allow them to leave such premises
calmly. When users close the door, the exit time will be reset and the panel will arm.
4.19 Double confirmation for duress
Duress means to force people to do something they do not want to do under threat of serious harm, in this
case, users may be forced to disarm their security systems.
To prevent such events, it is possible to ask the installer to enable the double confirmation function.
When this function is active, all disarm commands from remote control devices or M4 keys must be followed
by a keypad code; if the code is not digited within the set time interval, a duress alarm for the user that sent the
command is generated.
Control unit areas are equipped with individual timers to manage Double Confirmation function; a disarm
command that includes more than one area will affect the relevant timers as well.
WARNING: if the door is re-opened after the above procedure, such opening, even
if accidental, will trigger the intrusion alarm.
IN
OUT
R
TELESCOPIC LADDER CONTROL

20
VILLEGGIO - USER MANUAL - 090060699
Incase of user access (user code + OK) the duress alarm willnot be triggered for the areas including sectors
permitted for such user.
Max time interval: 42 minutes 30 secs.
Note: the confirmation code may be a user code different from the code that sent the disarm command;
please consider that a user can stoponly timers of areas including sectors authorized to him/her, and not timers
of different areas that will generate duress alarms as per normal configuration.
4.20 Multi-area management
VILLEGGIO is a multi-area control panel designed to manage 4 areas, each including 4 sectors, for a total
of 16 sectors.
Onboard keypad can manage all 4 areas; the areas can be accessed only if there is at least one user regi-
stered in the system with authorizations for the areas to be used. The keypad can be defined as ’system
keypad’ via software application in order to manage all 4 areas or the desired one.
When onboard keypad is configured as system keypad and users are inactive, LEDs will indicate system
status information. When onboard keypad is configured to manage a specific area and users are inactive, LEDs
will indicate status details of the specific area.
Note: user activity status is indicated by the LCD display backlight off and other related indications.
Note: when system keypad is selected, the display will show areas armed instead of sectors (backlit keys
indicate areas armed.)
VIDOMO panel can be connected to various control devices.
- Keypads: touch-screen TATTILO keypad or traditional models such as NIRVA and MIDAS keypads with
one or more pertaining area(s) and one presenting area; they can also be set as ’system keypads’.
The keypads provide visual information on current operating area; if no area is selected, they show system
general status and sectorkeys indicate areas armed status (also partial armed status.) To change current ope-
rating area, press OK key. In case of system keypads, press STOP to go back to system status display.
When operating from a keypad, users can only modify armed status of sectors pertaining to keypads and
to the user who is perfoming the operation.
When operating with the event log file, users can only display events pertaining to the keypad and the user
who is operating with the file.
- Key points: ETR-ZENITH and IZENITH flush mount control devices that can be configured only for one
area.
- Readers: I8 addressable reader that can be configured only for one area and only for specific sectors; it
can also be configured as "system reader".
4.20.1 Area managed by the keypad
VILLEGGIO unit keypad normally displays ’operating area’; in case of user inactivity, ’operating area’ coin-
cides with the ’presenting area’ (Area displayed on keypad.)
In case of multi-area setup, it is possible to change keypad ’operating area’ by pressing OK key (when in-
terface is idle) and by selecting the new area with the relevant numeral key.
Note: if there are no further areas available, this action will not be allowed.