Elmo PX-10E User manual

PＸ-30E/ PX-10E
VISUAL PRESENTER
INSTRUCTION MANUAL

2
■IMPORTANT SAFEGUARDS
■Read Instructions
All the safety and operating instructions should be read before the appliance is operated.
■Retain Instructions
The safety and operating instructions should be retained for future reference.
■Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
■Follow Instructions
All operating and use instructions should be followed.
■Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning.
■Attachments
Do not use attachments not recommended by the product manufacturer as they may
cause hazards.
■Water and Moisture
Do not use this product near water - for example, near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
■Placement
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child or adult, and serious damage to the
product. Use only with a cart, stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any mounting of the product should follow the
manufacturer’s instructions, and should use a mounting accessory recommended by the
manufacturer.
■Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable
operation of the product and to protect it from overheating, and these openings must
not be blocked or covered. The openings should never be blocked by placing the product
on a bed, sofa, rug, or other similar surface. This product should not be placed in a
built-in installation such as a bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
■Power Sources
This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home consult your
appliance dealer or local power company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
■Grounding or Polarization
This product may be equipped with either a polarized 2-wire AC line plug (a plug having
one blade wider than the other) or a 3-wire grounding type plug, a plug having a third
(grounding) pin. If the 2-Wire polarized plug will not fit in the outlet, try reversing the
plug. If the plug still fails to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug. The 3-wire grounding type plug
will fit into a grounding type power outlet.
This is a safety feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the
grounding type plug.
■Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they exit from the product.

3
■Lightning
For added protection for this product during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to the product due
to lightning and power-line surges.
■Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as
this can result in a risk of fire or electric shock.
■A product and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the
product and cart combination to overturn.
■Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
■Servicing
Do not attempt to service this product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified
service personnel.
■Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
• When the power-supply cord or plug is damaged.
• If liquid has been spilled, or objects have fallen into the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an
improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to its normal
operation.
• If the product has been dropped or damaged in any way.
• When the product exhibits a distinct change in performance - this indicates a need
for service.
■Replacement Parts
When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as
the original part. Unauthorized substitutions may result in fire, electric shock or other
hazards.
■Safety Check
Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
■Heat
The product should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.

4
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the product.
SA 1966
SA 1965
This symbol [crossed-out wheeled bin WEEEAnnex IV] indicates
separate collection of waste electrical and electronic equipment in
the EU countries.
Please do not throw the equipment into the domestic refuse.
Please use the return and collection systems available in your
country for the disposal of this product.

5
FOR UNITED STATES USERS:
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
USER-INSTALLER
CAUTION:
Your authority to operate this FCC verified equipment could be voided if you make changes
or modifications not expressly approved by the party responsible for compliance to Part 15
of the FCC rules.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
The connection of a non-shielded equipment interface cable to this equipment will invalidate the
FCC Certification or Declaration of this device and may cause interference levels which exceed the
limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use
a shielded equipment interface cable with this device. If this equipment has more than one interface
connector, do not leave cables connected to unused interfaces. Changes or modifications not
expressly approved by the manufacturer could void the user’s authority to operate the equipment.

6
BEFORE YOU USE
■Be sure to use the supplied power cord and the AC adapter.
■The power cord and AC adapter that come with this product are for this product only. Do
not use them with another product.
■Be sure to use the power cord applicable to your local power specifications. If the product
was sold in Japan, use the AC adapter sold with the product with 100 VAC and 50 or 60 Hz.
■When storing the product, do not leave it under direct sunlight or by heaters. It may be
discolored, deformed, or damaged.
■Do not place this product in any humid, dusty, salt bearing wind, or vibrating locations.
Use it under the following environmental conditions:
Temperature：0℃～ 40℃Humidity：30％～ 85％(No condensation)
■Do not put your finger between the arms when moving the arm. You may pinch your finger
and result in injury.
It is recommended to attach the supplied caution sticker to the product.
■Use a soft, dry cloth for cleaning.
Do not use any volatile solvent such as thinner or benzene.
■Do not point the lens directly to the sun. It could degrade the imaging capability.
■Luminescent and Black Spots
There may be some pixels that do not properly operate due to the use of CMOS Area
Image Sensors made-up of many pixels.
Though luminescent or black spots may be found on the screen, it is a phenomenon
peculiar to the CMOS Area Image Sensors and is not a malfunction.
■A protection sheet is attached to the touchscreen at the factory to avoid damage during
transportation. Remove the sheet before use.
Do not strongly press the touchscreen or press it with sharp objects. This may result in
damage or malfunction to the touchscreen.
■Follow the guidelines below to prevent the unit from dropping or overturning.
・Use the product on a stable base, desk, or table. Do not place the product on an
unstable base or slanted location.
・Place or wire the product so as to prevent the cables from being pulled or drawn.
■Never hold the product by the arm or the camera head. Carry the product by holding the
lower part of the main unit in both hands after folding the arm and the camera head.
■Pay careful attention when using (including setting-up and storing) or carrying the product
to prevent the camera head from receiving any shocks.
■After folding the product, do not place heavy object on the arm.
■Do not look directly into the LED light. If you look directly into it at pointblank range, your
eyes may be injured.
■The LED may get hot after using it for long hours. Do not touch it directly.
It is recommended to attach the supplied caution sticker to the product.
■Depending on the type of the SD card or USB flash drive, it may not be used with the
product.
■Transfer the data from the SD card or USB flash drive onto a device such as a PC to save
a backup copy.Malfunction of the product or repairs to it may cause the data saved in the
SD card or USB flash drive to be deleted.
■If this product is used for longer than the warranty period, its performance and quality
may deteriorate due to the lifetime of its parts. For parts replacement (on chargeable
basis), consult the dealer from whom you purchased this product or our branch/office near
your location.
■Battery precautions:
・Remove the battery from the remote control when not in use for an extended period of
time.
・Do not use a rechargeable battery.
・Do not charge or short-circuit the battery.

7
・Follow the regulations of the city or town when disposing of the battery.
・Pay attention to the polarity (+ / - ) of the battery.
・Children may ingest small batteries; always keep batteries safe and out of reach. If a
battery is swallowed, consult a doctor immediately as this could result in asphyxiation
or be an obstacle to digestion, etc.
・If any liquid from a battery leaks onto your skin or clothes, flush the area with clean
water immediately. If it gets into your eye, flush immediately with clean water and then
contact a doctor.
■Microphone
Connecting a microphone other than an electret condenser microphone (a microphone for
a computer) may cause malfunction.
■Audio input port
The power is supplied to the audio input port (dedicated for the microphone input). Do not
connect any audio line-output devices such as a CD/MP3 player to the audio input port.
■Menu and Icons
Some functions of this product may not be set or used depending on the operation mode
or menu settings.
■Recording / Playback
・Before recording an important scene, make sure to do a test recording to confirm that
the camera is working properly.
・The recording time varies depending on the resolution setting, recording quality setting
or type of SD card.
・Video files that are recorded with this product or converted by the proprietary software
can only be played with this product.
・Be careful not to operate the touchscreen or touch any buttons during the recording.
The operation noise may be recorded.
■Whiteboard Sheet
・Use a proper whiteboard marker. If you use a permanent parker on the board, you may
not be able to erase it.
・When writing, write on the whiteboard sheet. If you write directly on the stage, You
may not be able to erase it.
It is recommended to attach the supplied caution sticker to the product.
・Do not leave writing or drawings on the writing surface for an extended period of time.
It may stick to the surface and will be difficult to erase.
・It may be difficult to erase writing or drawings on the surface with a whiteboard eraser.
We recommend you used a melamine sponge.
■Remote control
The receivable range may be reduced when the product is placed in direct sunlight or near
an inverter fluorescent light.
Depending on the surrounding environment, the receivable range may be shorter or the
sensor may fail to receive any infrared light. In such cases, relocate the product or shield
the light source.
■Network Function (For PX-30E only)
We do not guarantee the performance when the product is connected to the Internet
directly. For details of the network settings, consult with your network administrator.
■Copyright
Unless used for personal use, it is prohibited strictly under copyright law to use any photo
files without the prior consent of the copyright holder. Even if using for personal use, be
careful that there could be a situation where video or audio recording is restricted or
illegal.

8
②Carrying the product
To avoid malfunction of the camera,
fold the arm before carrying
the product.
Never hold the product by the arm
or the camera head when carrying
the product.
HANDLING PRECAUTIONS
The followings are special precautions against mishandling of the product. Pay close attention
to them.
③Setting Up
When setting up the product, pay
attention not to pinch fingers
between moving parts.
①Installation
Do not place the product on an
unstable place or slanted surface.
④Cabling of the AC adapter
Do not wrap the power cable tightly
around the AC adapter. By doing so
may cause cable disconnection.

9
■TABLE OF CONTENTS
■IMPORTANT SAFEGUARDS············································································· 2
BEFORE YOU USE··································································································6
HANDLING PRECAUTIONS······················································································8
■TABLE OF CONTENTS ···················································································· 9
➊PREPARATION······························································································11
◆PACKAGE CONTENTS ···················································································11
➋BASIC OPERATIONS······················································································12
➋-1 ABOUT THE DOCUMENT CAMERA ·····························································12
◆PART NAMES······························································································12
◆OPERATING PANEL·····················································································13
◆REAR PANEL······························································································14
◆SIDE PANEL ·······························································································15
◆MOVING PARTS OF THE DOCUMENT CAMERA ··············································15
◆SETTING UP·······························································································16
◆FOLDING THE DOCUMENT CAMERA·····························································16
➋-2 SUPPLIED ACCESSORIES·········································································17
◆REMOTE CONTROL ····················································································17
◆WHITEBOARD SHEET··················································································18
◆CAUTION STICKER ·····················································································18
➋-3 SHOOTING IMAGES··················································································20
◆CONNECTING TOA PROJECTOR OR MONITOR ·············································20
◆TURNING ON/OFF THE POWER····································································20
◆ADJUSTING THE SIZE ·················································································21
◆AF (AUTO FOCUS)·······················································································22
◆USING THE LCD TOUCHSCREEN··································································23
◆ADJUSTING THE BRIGHTNESS·····································································24
◆TURNING ON/OFF THE LED LIGHTING ··························································25
◆SELECTING THE IMAGE SOURCE·································································26
➋-4 CONFIGURING THE SETTINGS··································································27
◆HOW TO CONFIGURE THE SETTINGS···························································27
◆DETAILS ABOUT FUNCTIONS·······································································32
➌ADVANCED OPERATIONS··············································································34
➌-1 USING SD CARD/USB FLASH DRIVE···························································34
◆RECORDING·······························································································35
◆DISPLAYING RECORDED FILES····································································37
➌-2 ABOUT RS-232C······················································································42
◆CONNECTION VIA RS-232C··········································································42
➌-3 ABOUT NETWORK FUNCTION (FOR PX-30E ONLY)······································44
➌-4 FIRMWARE UPDATE PROCEDURE····························································44
➌-5 ABOUT EIT(ELMO INTERACTIVE TOOLBOX)···············································45
➌-6 ABOUT SECURITY SLOT ··········································································45
➌-7 USING AUTO LOCK··················································································45
➌-8 USING WOL [WAKE ON LAN] FEATURE (FOR PX-30E ONLY)·························46
➌-9 USING IN MASS STORAGE MODE·····························································46
➌-10 Using the MF mode ·················································································47
➌-11 Using theAV control mode (for PX-30E only) ················································47
➍ERROR MESSAGES ······················································································49
➎TROUBLE SHOOTING····················································································50
➏SPECIFICATIONS··························································································53
■TRADEMARKS AND LICENSES ·········································································55

10
MAIN FEATURES
★High-Definition 4K Image
With the 12Mega pixels CMOS sensor, the PX-10E/30E can produce high-definition images with max.
4K resolution.
※The PX-10E cannot output 4K images. The max output resolution is 2K.
★Natural, Smooth Image
The PX-10E/30E can output 2K images at 60fps.
High definition and smooth video images can be fully displayed without degrading the image quality.
★Maximum excitement generated by state-of-the-art zoom –Optical zoom, Digital
zoom, Sensor zoom
The PX-10E/30E are equipped with 12x Optical zoom and 2x Sensor zoom. 24x zooming without
image degradation is possible.(Total 288x zooming together with 12x digital zoom.)
★Both A4 portrait image and A3 landscape image can be captured, respectively, in
HDMI output mode
By changing the settings of the angle of view and resolution of the output image, you can capture full
A4 portrait image and A3 landscape image respectively.
★Easy to store and carry
Thanks to its thin and lightweight design, the PX-10E/30E can be easily stored and carried.
★Possible to record HDMI input
The PX-10E/30E can record or capture HDMI signals being sent to the unit.
The HDMI signals being sent to the unit can be output as HDMI signals, RGB signals, and HDBasetT
signals (for PX-30E only).
★Extendable with HDBaseT (for PX-30E only)
Using the LAN cable, the PX-30E can transmit uncompressed 2K video signals up to 100m at high
frame rate, without delay.(For 4K video signals, up to 70m.)
★HDMI1.4 compliant (4K)
The PX-10E/30E support HDMI1.4, which allows the transfer of 4K/2K video signals and the network
connection in a single cable.
★USB3.0 compliant (4K)
The PX-10E/30E support USB3.0, which allows the high-speed data transfer of max.5Gbps (10 times
faster than USB2.0). Suitable for the transmission of large volumes of data such as high resolution
image data, audio data, and video data.
★Recording and playback of 4K videos（for PX-30E only ）
It is possible to record or playback 4K videos.
★Possible to draw on the stage (can be used as a whiteboard)
By placing the supplied whiteboard sheet on the stage, you can draw directly on the sheet with a
whiteboard marker and shoot it.
★Bright LED lighting
The small LED lighting of the PX-10E/30E is designed to reduce glare to a minimum by focusing lights
with lenses.
It delivers bright and even illumination to the entire stage.