Lumens DC-W80 User manual

DC-W80
4K Document Camera
User Manual - English
[Important]
To download the latest versions of the Quick Start
Guide, multilingual user manual, software, driver,
etc., please visit Lumens
https://www.MyLumens.com/support

English - 1
Table of Contents
Copyright Information.......................................................................................3
Chapter 1 Safety Instructions ..........................................................................4
Chapter 2 Package Contents ...........................................................................5
Chapter 3 Product Overview............................................................................6
3.1 Overview.............................................................................................6
3.2 Extension angle..................................................................................6
3.3 Notes for Operation............................................................................7
3.4 I/O functions Introduction ...................................................................7
3.5 Description of LED indicator...............................................................8
3.6 Relative position of the presenter and document...............................9
Chapter 4 Installation and Connections .......................................................10
4.1 Machine Size....................................................................................10
4.2 Installation and setup .......................................................................10
4.3 Connecting to a computer and use Lumens™ software (Wi-Fi mode)11
4.4 Connect to a projector, monitor or HDTV (HDMI mode).................. 11
4.5 Connecting to a computer and use Lumens™ software (USB Mode)12
4.6 Installing Application Software..........................................................12
Chapter 5 Start Using......................................................................................13
5.1 Direct Use (HDMI Mode)..................................................................13
5.2 Use with Ladibug (Wi-Fi Mode)........................................................14
5.3 Use with Ladibug (USB Mode).........................................................16
Chapter 6 Introductions to Control Panel Buttons......................................17
Chapter 7 Descriptions of Major Functions..................................................18
7.1 I would like to automatically adjust the image to have the best
brightness and focusing performance..........................................................18

English - 2
7.2 I would like to freeze the live image .................................................18
7.3 I would like to turn on/off the lamp....................................................18
7.4 I would like to zoom in/out images ...................................................18
7.5 I would like to adjust the brightness .................................................18
7.6 I would like to rotate the image.........................................................19
7.7 I would like to enlarge a part of the image .......................................19
Chapter 8 Wi-Fi Connection Setting..............................................................20
8.1 Network connection..........................................................................20
8.2 Log in to the web page.....................................................................20
8.3 Web Page Menu Function Description.............................................21
Chapter 9 Set DC-W80 as an AP....................................................................30
9.1 Connection Diagram.........................................................................30
9.2 Device Requirements.......................................................................30
9.3 Setting DC-W80................................................................................30
Chapter 10 DIP Switch Setting.......................................................................33
10.1 Description of DIP ..........................................................................33
10.2 Resolution Switch ..........................................................................33
Chapter 11 Troubleshooting...........................................................................34
Supplier's Declaration of Conformity 47 CFR § 2.1077 Compliance
Information......................................................................................................35

English - 3
Copyright Information
Copyrights © Lumens Digital Optics Inc.All rights reserved.
Lumens is a trademark that is currently being registered by Lumens Digital Optics
Inc.
Copying, reproducing or transmitting this file is not allowed if a license is not
provided by Lumens Digital Optics Inc. unless copying this file is for the purpose
of backup after purchasing this product.
In order to keep improving the product, Lumens Digital Optics Inc. hereby
reserves the right to make changes to product specifications without prior notice.
The information in this file is subject to change without prior notice.
To fully explain or describe how this product should be used, this manual may
refer to names of other products or companies without any intention of
infringement.
Disclaimer of warranties: Lumens Digital Optics Inc. is neither responsible for any
possible technological, editorial errors or omissions, nor responsible for any
incidental or related damages arising from providing this file, using, or operating
this product.

English - 4
Chapter 1 Safety Instructions
Always follow these safety instructions when setting up and using the DC-W80 Document Camera:
1 Operation
1.1 Please use the product in the recommended operating environment, away from water or source of heat
1.2 Do not place product in tilted position or unstable trolley, stand or table.
1.3 Please clean the dust on the power plug prior to usage. Do not insert the product’s power plug into a
multiplug to prevent sparks or a fire.
1.4 Do not block the slots and openings in the case of DC-W80 Document Camera. They provide ventilation
and prevent the DC-W80 Document Camera from overheating.
1.5 Do not open or remove covers, otherwise it may expose you to dangerous voltages and other hazards.
Refer all servicing to licensed service personnel.
1.6 Unplug the DC-W80 Document Camera from the wall outlet and refer servicing to licensed service
personnel when the following situations happen:
If the power cords are damaged or frayed.
If liquid is spilled into the product or the product has been exposed to rain or water.
2 Installation
2.1 For security considerations, please make sure the standard hanging rack you bought is in line with UL or
CE safety approbations and installed by technician personnel approved by agents.
3 Storage
3.1 Do not place the product where the cord can be stepped on as this may result in fraying or damage to the
lead or the plug.
3.2 Unplug the product during thunderstorms or if it is not going to be used for an extended period.
3.3 Do not place the product or accessories on top of vibrating equipment or heated objects.
4 Cleaning
4.1 Disconnect all the cables prior to cleaning and wipe the surface with a dry cloth. Do not use alcohol or
volatile solvents for cleaning.
5 Batteries (for products or accessories with batteries)
5.1 When replacing batteries, please only use similar or the same type of batteries.
5.2 When disposing of batteries or products, please adhere to the relevant instructions in your country or
region for disposing of batteries or products.
Precautions
This symbol indicates that this
equipment may contain dangerous
voltage which could cause electric
shock. Do not remove the cover (or
back). No user-serviceable parts inside.
Refer servicing to licensed service
personnel.
This symbol indicates that there
are important operating and
maintenance instructions in this
User Manual with this unit.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Notice :
The changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

English - 5
Chapter 2 Package Contents
DC-W80
USB cable (USB 2.0)
Quick Installation
Guide

English - 6
Chapter 3 Product Overview
3.1 Overview
3.2 Extension angle
<Caution > Please only operate in the extended angles as illustrated.
Improper usage may damage the machine.
Support Arm
Control panel
LED Indicator
Lens/Lamp

English - 7
3.3 Notes for Operation
<Note>When moving the device, do not grasp the front of the lens or the
body. Please use both hands to hold the bottom of the device. Handling the
device improperly may cause machine failure.
3.4 I/O functions Introduction
NO.
Item
Function Descriptions
1
Power LED Indicator
Display the status of the machine. Please refer to 3.5
Description of LED indicator
2
Wi-Fi LED Indicator
Display the status of the Wi-Fi. Please refer to 3.5
Description of LED indicator
3
Battery LED Indicator
Display the status of the battery. Please refer to 3.5
Description of LED indicator
Back View
Front View

English - 8
NO.
Item
Function Descriptions
4
Kensington safety lock
Lock hole of safety lock
5
Reset Button
Press the button for initialization to reset to original
factory settings.
6
DIP Switch Setting
Adjust the resolution setting. The default is
1920*1080/30 fps.
To switch the setting, please refer to Chapter 10 DIP
Switch Setting
7
Mode Switch Button
Switch Modes: Wi-Fi / HDMI / USB
8
HDMI output port
Connect to HDMI output signal source
9
USB Type-B port
The USB port is for connecting to the USB port of the
computer which provides USB signal images and
power
3.5 Description of LED indicator
Name
Indicator Status
Power
Flickering blue light: Startup in progress, initialization
Blue light stays lit: Startup completed
Flickering red light: A startup failure or error has occurred
Pink light stays lit: Already powered on, indicating low power
and need to connect to the USB cable for charging
Wi-Fi
Blue light stays lit: Switched to the Wi-Fi Mode and the startup
is completed
No Light: In another operating mode
Battery
Indicator light is green
After connecting the USB cable and the flickering indicator light
will indicate that it is charging
Press “Battery Check” button to display the battery
level
Battery level ≥ 75%
Battery level 50% ~ 75%
Battery level 25% ~ 50%
Battery level 3% ~ 25%
Battery level < 3%
Flickering green light

English - 9
3.6 Relative position of the presenter and document
Computer
Projector

English - 10
Chapter 4 Installation and Connections
4.1 Machine Size
Length x Width x Height: Extended－306 x 140 x 373 mm
Closed－137 x 140 x 270 mm
Weight: 1.35 kg
4.2 Installation and setup
Please set up the DIP switch setting first. Refer to Chapter 10 DIP
Switch Setting.
Please confirm that the product is switched to the desired mode
(Wi-Fi/HDMI/USB)
Wi-Fi Mode
HDMI Mode
USB Mode

English - 11
4.3 Connecting to a computer and use Lumens™
software (Wi-Fi mode)
※Please download the relevant software from Lumens website. For more information on the
connection method, please refer to Chapter 8 Wi-Fi Connection Setting.
4.4 Connect to a projector, monitor or HDTV (HDMI mode)
Computer
HDMI cable
Monitor
Projector
HDTV
or
or

English - 12
4.5 Connecting to a computer and use Lumens™
software (USB Mode)
<Remark>Please download the relevant software from Lumens website.
4.6 Installing Application Software
The application software installed on the computer enables you to:
Control DC-W80.
Capture and record images.
Annotate the image, highlight important details and save it.
Support the full screen function.
<Caution>Please download the relevant software from the Lumens
website. For installation steps and software operation, please
refer to the Ladibug™ 4K software user manual.
4.6.1 System Requirements
Windows System: Windows 7 or later
Chrome system
Mac System: Mac OS X 10.12 and above
USBCable
HDMICable
Projector
Computer

English - 13
Chapter 5 Start Using
5.1 Direct Use (HDMI Mode)
1. Charge for a recommended 10.5 hours prior to first-time operation. The device
is fully charged when all the power bars are full and the green light is constant
on.
2. Place an object to be displayed under the camera.
3. Turn on the power and adjust the operation mode according to the
connection method.
4. Adjust the support arm and lens to the appropriate positions.
5. Press [AUTO TUNE] button to optimize the image.
6. You are ready to teach/present.
Computer
Projector

English - 14
5.2 Use with Ladibug (Wi-Fi Mode)
5.2.1 Network Connection
Switch DC-W80 to Wi-Fi mode, and Wi-Fi LED light turns blue. Open
the Wi-Fi network list on the computer, and choose
[DC-W80_5G_XXXXXX] (XXXXXX: last six digits of the MAC address).
Enter the connection password (default password: 88889999) to
enable the connection.
5.2.2 Use Ladibug to connect to DC-W80
1. Open Ladibug, click to open the [Search Window], and select
[Wireless Document Camera].
1
2

English - 15
2. Click ,and select a DC-W80 in the list after the search is
completed.
3. Log in as anAdmin or a Viewer. The default password for Admin is
9999.
4. After connecting to DC-W80 by clicking [Log In], you can start using it.
1
2

English - 16
5.3 Use with Ladibug (USB Mode)
1. Switch to USB mode, and use a USB cable to connect DC-W80
and the computer.
2. Open Ladibug, click to open the [Search Window], and
select [USB Document Camera].
3. You can start using DC-W80.
1
2

English - 17
Chapter 6 Introductions to Control Panel
Buttons
Icon
Function Descriptions
Turn on and off
Short press: power on (under stand by)
Press for 1 second: turn off (under power on)
Press for 10 seconds: force to turn off
Battery level check
Auto Tune
Automatically adjust the image to have the best brightness
and focusing performance
,,,
Left, right, up, down buttons, used for moving in a direction
at the partial enlarged mode
Enable/Disable the partial enlarged mode
/
Adjust the brightness of the image
/
Zoom in/out images
Rotate image: 0°/ 90°/ 180°/ 270°/Vertical flip/Horizontal flip
LED lamp mode toggle switch: off / brightness 1 / brightness
2 / brightness 3
<Remark>Brightness 3 is the brightest state
Freeze
Freeze the current image to remain temporarily on the
screen. Press again to defreeze

English - 18
Chapter 7 Descriptions of Major Functions
7.1 I would like to automatically adjust the image to have
the best brightness and focusing performance
Press [Auto Tune] for the best brightness and focusing performance.
7.2 I would like to freeze the live image
Press FREEZE to freeze the current image on the screen. Press
again to lift the freeze.
7.3 I would like to turn on/off the lamp
The default state of the lamp is off, press to turn it on or off. There
are three levels of brightness.
7.4 I would like to zoom in/out images
Press to zoom in the image.
Press to zoom out the image.
7.5 I would like to adjust the brightness
Press to make it brighter.
Press to make it darker.

English - 19
7.6 I would like to rotate the image
Press to rotate the image. (The sequence of switching is: 0°/ 90°/
180°/ 270°/Vertical flip/Horizontal flip)
7.7 I would like to enlarge a part of the image
1. Press to activate the partial enlarged mode.
2. Press [], [], [], or []to move and view the partial enlarged images.
3. Press to exit the partial enlarged mode.