Elnur Gabarron SOLARHHR20 Operation instructions

USER OPERATING INSTRUCTIONS
HIGH HEAT RETENTION STORAGE HEATER
VALID FOR PV INSTALLATIONS WITH
PHOTOVOLTAIC SURPLUS PRODUCTION
SOLAR HHR
MODELS
SOLARHHR20
SOLARHHR30
SOLARHHR40
Please read these instructions carefully before installing or using this appliance for the first time.

2
1. –IMPORTANT INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire,
electric shock, and injury to persons, including the following:
•Keep combustible materials, such as
furniture, pillows, bedding, papers, clothes,
etc. and curtains at least a foot (30cm) from
the front, sides and rear of the heater. It is
essential that the indicated minimum
clearances are maintained.
•CAUTION —Some parts of this product can
become very hot and cause burns. Particular
attention must be given where children and
vulnerable people are present.
•This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given supervision
or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
Children must not play with the appliance. Cleaning and user maintenance must not be made by children
without supervision.
•Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has
been placed or installed in its intended normal operating position and they have been given supervision or
instruction concerning use of the appliance in a safe way and understand the hazards involved. Children
aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user
maintenance.
•Children of less than 3 years should be kept away unless continuously supervised.
•Do not operate any heater after it malfunctions. Disconnect power at service panel and have heater
inspected by a reputable electrician before reusing. To disconnect heater, turn controls to off, and turn off
power to heater circuit at main disconnect panel.
•Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an
electric shock or fire or damage the heater.
•Do not use this heater to dry clothes. To prevent a possible fire, do not block air intakes or exhaust in any
manner. Air inlets and outlets provide proper operation of the appliance and prevent its overheating. DO
NOT cover air inlet and outlet grills.
•A heater has hot and arcing or sparking parts inside. Do not use in areas where gasoline, paint, or
flammable vapors or liquids are used or stored. The use of these heaters is forbidden in any area where
there is a presence of gases, explosives or inflammable objects. Never open a charged heater.
•SAVE THESE INSTRUCTIONS. This guide must be kept and given to any new user. Use this heater
only as described in this manual. Any other use not recommended by the manufacturer may cause fire,
electric shock, or injury to persons. The warranty of the heater will not cover any damage caused by non
observance of any of these instructions.
•Do not use this heater outdoors.
•Neither the connecting cable nor any other object must come into contact with the hot unit.
•After installation a survey of the first charging cycle should be carried out to ensure that the main input
thermostat switches off. Ventilate the room during this first cycle.
•The presence of air particles of smoke, dust and other pollutants could, in time, discolor the walls and
surfaces around the heater.
•Incorrect time settings, erroneous programming of the reduced rate time and too high temperature
settings may result in a high cost of your electricity bill.
min
3 "
75 mm
OBJECT
min
10"
250 mm
min
3 "
75 mm
CURTAIN, PIECE OF FURNITURE

3
2. - OPERATING INSTRUCTIONS
2.1. General information
CAUTION: DO NOT USE THIS HEATER TO DRY CLOTHES. Do not cover this heater at any time.
CONNECTION / DISCONNECTION
Power switch. All models are equipped with a switch on the back
side panel. It is used to connect and disconnect SOLAR HHR.
KEYBOARD:
Keep pressed the button to access the advanced configuration. Press this button to go back in the different menus.
Press the button to confirm values in the different menus.
Press the key to increase the displayed value or to advance through the different options available.
Press the key to decrease the displayed value or to move through the different options available.
ON/OFF
Once the heater is connected to a main supply you can turn the heater ON by switching the main ON/OFF switch positioned at
the rear right side of the heater as shown above.
BACKLIGHT
Pressing any button, the display will illuminate with a soft white colour. After certain time if no buttons are pressed the display
backlight will turn off.
Buttons only will respond when the backlight is on.
KEYBOARD LOCK
During any operation mode, it is possible to lock the keyboard by holding and simultaneously for 5 seconds. A pop-up
window will confirm the keyboard lock.
To unlock the keyboard, press and simultaneously for 5 seconds. A pop-up window will confirm the keyboard unlock.

4
2.2. Commissioning
An easy installation wizard is programmed in Solar HHR electronic control. Follow the start wizard instructions when turning
your SOLAR HHR on for the first time or after resetting it to the factory settings.
START WIZARD - INITIAL SETTINGS.
The Solar HHR electronic control will guide you through the commissioning of the unit. The steps to follow are:
a. Select language. Confirm the language in the storage heater electronic control.
b. Date & Time. Check and confirm that the default date & time in the unit is correct. If not, please change it.
c. Charging periods. 2 different charging periods can be set in SOLAR HHR. Set Charging Periods 1 & 2 according to your
electricity low tariff hours.
By default, SOLAR HHR is set to charge from 00:00 to 07:00 hours. If this charging time matches your electricity low tariff
hours, you do not need to make any changes in the unit configuration. Otherwise, you can change charging Periods 1 and 2 to
match your electricity tariff.
d. Temperature programme. This is the last step of the start wizard. Select and confirm the weekly temperature programme that
the heater will follow. By default, 3 different programmes and a 24-hours temperature setting are available.
-Programme 1. At Home.
oFrom Monday to Sunday. Comfort temperature from 07:00 to 22:00. ECO temperature the rest of time slots.
-Programme 2. Work M-F.
oFrom Monday to Friday. Comfort from 07:00 to 08:00 + 17:00 to 22:00. ECO the rest of time slots.
oSaturdays and Sundays. Comfort from 07:00 to 22:00. ECO the rest of time slots.
-Programme 3. Office Schedule.
oFrom Monday to Sunday. Comfort from 07:00 to 18:00. ECO the resto of time slots.
-Temperature 24h.
oThe same temperature 24 hours a day, 7 days a week.
In case you select one of the 3 predefined programmed, you can check or modify the programme in the next step as well as
modify the set-point temperature for every temperature level (Comfort, ECO and Frost Protection).
In case you select Temperature 24 hours, the installation wizard will ask to set the temperature you want to maintain 24 hours a
day, 7 days a week.
With the help of the start wizard, you will set your Solar HHR storage heater for an autonomous operation. It will charge and
store the heat during the charging hours set in c.. Charging Periods and it will adjust the charge level and consumption according
to the temperature programme of your choice.
An incorrect time, charging periods or set temperatures configuration, might result in a high cost of the electricity bill.
i
i

5
2.3. Utilization of photovoltaic surplus
PREPARATORY STEPS
Before using the PV surplus utilization function of your SOLAR HHR storage heaters, please perform the following steps:
a. Installation and setting of the control hub and power meters included in the Solar Box. Please follow the instructions included
within.
b. Download from your market app the Elnur Gabarron Wifi Control app, available for IOS & Android.
c. Create your user account in the app if you still do not have one.
d. Register the control hub included in the Solar Box using your user account. Then link also the power meters included in the
Solar Box if you still have not.
e. Link the SOLAR HHR storage heaters to the control hub using the app. (See point 4. Remote Operation using the G-Control
Hub for more detail).
To set and activate the PV surplus utilization function it is necessary to install the Solar Box device (1 Solar box per installation).
The PV surplus utilization function is only valid for installations for self-consumption connected to the grid and discharging energy
to the network.
ACTIVATION AND SETTING
The activation and setting of the PV surplus utilization function is done exclusively through the app.
Solar Energy activation. Surplus utilization
Once you have completed the aforementioned steps, access the app with your user name and keyword, and complete the following
steps:
-Access section “Heating” from the bottom menu.
-Select and access the appliance you want to set.
-Select the option “Setup” from the bottom menu
-Turn on or off the PV surplus utilisation function through the activation or deactivation of the “Activation State”
parameter in the “Solar Energy” menu.
i
i