Elo TouchSystems 2201L User manual

User Manual
2201L Touchmonitor
User Manual – 2201L
SW601363 Rev B - Page 1 of 22

User Manual – 2201L
SW601363 Rev B - Page 2 of 22
Copyright © 2011 Tyco Electronics. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language or computer language, in any form or by any means, including, but not
limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission
of Tyco Electronics.
Disclaimer
The information in this document is subject to change without notice. Tyco Electronics makes no
representations or warranties with respect to the contents herein, and specifically disclaims any
implied warranties of merchantability or fitness for a particular purpose. Tyco Electronics reserves the
right to revise this publication and to make changes from time to time in the content hereof without
obligation of Tyco Electronics to notify any person of such revisions or changes.
Trademark Acknowledgments
Elo TouchSystems, IntelliTouch, iTouch, Tyco Electronics and TE (logo) are trademarks of the Tyco
Electronics group of companies and its licensors. Windows is a trademark of the Microsoft group of
companies. Other product names mentioned herein may be trademarks or registered trademarks of
their respective companies. Tyco Electronics claims no interest in trademarks other than its own.

User Manual – 2201L
SW601363 Rev B - Page 3 of 22
Table of Contents
Chapter 1 - Introduction ........................................................................... 4
Chapter 2 – Installation............................................................................. 5
Chapter 3 – Mounting................................................................................ 9
Chapter 4 – Operation............................................................................... 10
Chapter 5 – Technical Support............................................................... 14
Chapter 6 – Safety & Maintenance........................................................ 15
Chapter 7 – Regulatory Information..................................................... 16
Chapter 8 – Warranty Information......................................................... 19

User Manual – 2201L
SW601363 Rev B - Page 4 of 22
Chapter 1 - Introduction
Product Description
Your new touchmonitor combines Elo TouchSystems’ reliable performance with the latest
developments in touch technology and display design. This combination of features creates a
natural flow of information between a user and the touchmonitor.
This touchmonitor incorporates a 24-bit color, active matrix thin-film-transistor LCD panel to
provide high quality display performance. Its Full HD resolution of 1920x1080 is suitable for
displaying graphics and images. Its LED backlight significantly reduces power consumption and
eliminates mercury (compared to CCFL-backlit panels). Other features that enhance this LCD
monitor’s performance are Plug & Play compatibility, built-in speakers and headphone output
capability, on-screen display (OSD) controls, and a family of peripherals including webcam and
magnetic stripe reader.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user manual to
maximize the life of your unit and prevent risks to user safety. See the Safety & Maintenance
chapter for more information.
This manual contains information that is important for the proper setup and maintenance of the
unit. Before setting up and powering on your new touchmonitor, read through this manual,
especially the Installation, Mounting, and Operation chapters.

Chapter 2 –Installation
Unpacking the Touchmonitor
Open the carton and verify the following items are present:
Touchmonitor with protective sheet for its face
Elo TouchTools CD
Quick Install Guide
Japanese language regulatory information pamphlet
DVI cable
VGA cable
USB cable
Audio cable
AC-DC power adapter
North America, Europe/Korea, United Kingdom, Taiwan, China, Korea, & Japan power cables
3-pin to 2-pin adapter for Japan power cable
Connector Panel & Interfaces
Remove the cable cover on the back of the unit to access the touchmonitor’s connector panel.
User Manual – 2201L
SW601363 Rev B - Page 5 of 22

Touchmonitor Connections
1. Connect the DVI or VGA video cables between the monitor’s DVI/VGA input connectors and
your DVI/VGA video source, respectively. Tighten the video cable’s screws for best
performance.
2. Connect the USB touch cable between the monitor’s USB connector and your PC’s USB
port.
3. Connect the audio cable between the monitor’s Audio In jack and your audio source.
4. Select the correct power cable for your region. Connect the cable between the AC power
source and the power adapter’s input connector. Connect the power adapter’s DC output
connector to the monitor’s input power jack.
5. Replace the cable cover, if desired. Cables can be routed inside the stand – remove and
replace the stand cable cover for access and routing.
6. The touchmonitor ships in an OFF state. Press the power button to turn it on.
User Manual – 2201L
SW601363 Rev B - Page 6 of 22

Installing the Touch Technology Software Drivers
Some software installation is required for your touchmonitor to work with your computer.
The drivers for the Windows 7, XP, Vista, WePOS, and 32-bit Server 2003 operating systems
are provided with your touchmonitor on a CD.
Visit the Elo TouchSystems website www.elotouch.com for:
The most up-to-date touch driver versions
Additional touch driver information
Detailed touch driver installation guides
Touch drivers for other operating systems
Insert the Elo TouchTools CD into your computer’s CD-ROM drive. The CD should
automatically run the Elo TouchTools application. Select “Install Driver for This computer”:
User Manual – 2201L
SW601363 Rev B - Page 7 of 22

For Windows XP, Vista, Server 2003, Server 2008, and WEPOS installations, install the “USB
Touchscreen Drivers” when prompted:
For Windows 7 installations, check the “Install driver” box under “Elo USB Interfaces – Other
Touchscreens”
User Manual – 2201L
SW601363 Rev B - Page 8 of 22

User Manual – 2201L
SW601363 Rev B - Page 9 of 22
After accepting the end-user license agreement, the drivers will finish installing.
Reboot your computer after the install is complete.

Chapter 3 – Mounting
General Mounting Information
The OSD text can be rotated through the OSD menu to better suit your mounting orientation.
The holes located on the sides and top of the touchmonitor case are for ventilation. Do not
block, cover, or insert anything inside the ventilation slots.
Rear VESA Mount
A four-hole 100x100mm mounting pattern for M4 screws is provided on the rear of the
monitor. Remove the stand using a Phillips screwdriver to access this mounting interface.
The VESA FDMI-compliant mounting is coded: VESA MIS-D, 100, C
Stand Mounting
Threaded through-holes are provided on the bottom of the stand base for mounting or
securing.
User Manual – 2201L
SW601363 Rev B - Page 10 of 22