Elo TouchSystems Entuitive ET1566L-7SWC-1 User manual

(OR(QWXLWLYH7RXFKPRQLWRU
8VHU*XLGH
/&'3DQHO0RXQW7RXFKPRQLWRU
(7/6 &
5HYLVLRQ&
31
(OR7RXFK6\VWHPV,QF
(/2728&+
ZZZHORWRXFKFRP

1
Chapter 1
Introduction 1
Precautions . . . . . . . . . . . . . . . . . . . . 1
About the Product . . . . . . . . . . . . . . . . . 1
Chapter 2
Installation and Setup 3
Unpacking Your Panel Mount
Touchmonitor . . . . . . . . . . . . . . . . . . 4
Product Overview . . . . . . . . . . . . . . . . . 5
Main Unit . . . . . . . . . . . . . . . . . . . . 5
Rear View . . . . . . . . . . . . . . . . . . . 5
Bottom View . . . . . . . . . . . . . . . . . . 6
Remote OSD with Cable Attachment . . . . . 6
Mounting Your Touchmonitor . . . . . . . . . . . 7
Connecting Your Touchmonitor . . . . . . . . . . 8
Optimizing the LCD Display . . . . . . . . . . . 11
Installing the Driver Software . . . . . . . . . . 12
Installing the Serial Touch Driver for Windows
XP, Windows 2000, Me, 95/98 and NT 4.0 . 13
Installing the Serial Touch Driver for MS-DOS
and
Windows 3.1 . . . . . . . . . . . . . . . 14
Chapter 3
Operation 15
About Touchmonitor Adjustments . . . . . . . . 15
Connecting the OSD Module . . . . . . . . . . 16
OSD Module Controls . . . . . . . . . . . . . . 17
OSD Menu Function. . . . . . . . . . . . . . . 18
Chapter 4
Troubleshooting 19
Solutions to Common Problems. . . . . . . . . 19
Appendix A
Native Resolution 21
Appendix B
Touchmonitor Safety 23
Care and Handling of Your Touchmonitor . . . . 24
Appendix C
Technical Specifications 25
Compatibility Modes . . . . . . . . . . . . . . 25
Touchmonitor Specifications . . . . . . . . . . 26
15" LCD Touchmonitor (ET1566L) Specifications
26
AccuTouch Touchscreen Specifications . . . 27
15" LCD Panel Mount Touchmonitor (ET1566L-
7SWC-1) Dimensions . . . . . . . . . . . 28
Panel Cutout . . . . . . . . . . . . . . . . . 30
Regulatory Information 31
Warranty 35
Index 37
Table of Contents

2

3
Copyright © 2003 Elo TouchSystems Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language or computer language, in any form or by any means, including, but not
limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written
permission of Elo TouchSystems.
Disclaimer
The information in this document is subject to change without notice. Elo TouchSystems makes no
representations or warranties with respect to the contents hereof, and specifically disclaims any
implied warranties of merchantability or fitness for a particular purpose. Elo TouchSystems reserves
the right to revise this publication and to make changes from time to time in the content hereof
without obligation of Elo TouchSystems to notify any person of such revisions or changes.
Trademark Acknowledgments
IntelliTouch, SecureTouch, AccuTouch, Entuitive, and MonitorMouse are trademarks of Elo
TouchSystems, Inc.
Other product names mentioned herein may be trademarks or registered trademarks of their
respective companies. Elo TouchSystems claims no interest in trademarks other than its own.

1-1
CHAPTER
C HAPTER 1 I NTRODUCTION
Congratulations on your purchase of an Elo TouchSystems Entuitive LCD panel
mount touchmonitor. Your new high-resolution industrial touchmonitor
combines the reliable performance of Elo’s touch technology with the latest
advances in LCD display design. This combination of features creates a natural
flow of information between you and your touchmonitor.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user’s manual to maximize the life of your unit. See Appendix B for more
information on touchmonitor safety.
About the Product
Your LCD panel mount Touchmonitor is a 15" XGA TFT color display with the
following features:
• Direct analog RGB input
• 15.0” diagonal screen size
• 16.7 million displayable colors (262,144-1549L)
• 1024 x 768 resolution
• XGA/ SVGA/ VGA/ VESA/ Mac/ NEC PC-98 compatible
• 24~60kHz horizontal scan
• 56~75Hz refresh rate

1-2 Elo Entuitive Touchmonitor User Guide
• Auto adjustment capability
• High quality full screen re-scaling
• Multilingual OSD menus in four languages: English, French, Italian,
Spanish, and Japanese
• VESA flat panel monitor physical mounting interface (75mm)
• Worldwide agency approvals that include UL*, CUL*, TÜV- Bauart, FCC,
CE, C-Tick, VCCI
•Certified by UL to NEMA 4, 4x and 12: ET1566L-7SWC-1*
•Designed to meet NEMA 4, 4x & 12: ET1566L-9SWC-1/5*
*ITE recognized component
For full Product Specifications refer to Appendix C.

2-3
CHAPTER
C HAPTER 2 I NSTALLATION AND S ETUP
This chapter discusses how to install your LCD panel mount touchmonitor and
how to install Elo TouchSystems driver software.

2-4 Elo Entuitive Touchmonitor User Guide
Unpacking Your Panel Mount
Touchmonitor
Check that the following 7 items are present and in good condition:
/&''LVSOD\
0RQLWRUSRZHUFDEOH86&DQDGD
(XURSHDQPRQLWRUSRZHUFDEOH
9LGHRFDEOH
6HULDOWRXFKVFUHHQ
FDEOH
XLFN,QVWDOODWLRQ*XLGHDQG
26'PRGXOH
AUTO/SEL DOWN UP MENU
1RWHVKLSPHQWVWRWKH8.ZLOO
FRQWDLQD8.SRZHUFRUGDOVR
Quick
Installation
Guide
CD
Software
VRIWZDUH&'

2-5
Product Overview
Main Unit
Rear View
LCD Display

2-6 Elo Entuitive Touchmonitor User Guide
Bottom View
Remote OSD with Cable Attachment
Customer Panel
AUTO/SEL DOWN UP MENU

2-7
Mounting Your Touchmonitor
N OTE : You will need a 6mm allen socket and torque wrench (Hex) to attach the mounting
brackets.
Your panel mount touchmonitor comes with 6 mounting brackets (and 6
screws). You will need 6 brackets to mount your touchmonitor. Two brackets
attach to the top and bottom and one on each side.
To mount your touchmonitor to a panel, follow the steps below:
1Prepare the opening in the panel (307mm x 398.2mm/12.08" x 15.68"). See
page C-36. Mounting panel thickness must not exceed 13mm.
2Disassemble the 6 brackets and NEMA frame.
3Verify that your touchmonitor will clear the opening as you attempt to front
mount it. The opening will be covered by the bezel flanges.
4Mount the touchmonitor from the front side of the opening in the supporting
panel and temporarily secure it.
5From the back of the panel opening, slip the NEMA frame over the rear
cover. Attach the 6 brackets into the slots. Use 2 brackets on top and bottom
and 1 on each side.
6To secure the touchmonitor, turn the screws clockwise until a firm
contact is made with the NEMA frame. To assure a “flat” mount, screws
should be tightened “cris-cross” and not sequentially, i.e. tighten the
upper left corner screw first then the lower right screw. Torque screws
to 35 in lbs. (4 Nm).

2-8 Elo Entuitive Touchmonitor User Guide
Connecting Your Touchmonitor
The following illustrations guide you step by step in connecting your
touchmonitor.
Before connecting the cables to your touchmonitor and PC, be sure that the computer
and the touchmonitor are turned off.
Serial
touchscreen
connector
Female 15-pin
video
connector
Video cable
Connections on underside
US
power cable
European
power cable
Power
OSD module
Power switch
Serial cable
AUTO/SEL DOWN UP MENU
OSD module
connector

2-9
STEP 1-Connecting the Video Cable
• Connect the 15-pin video cable (the ferrite bead end) to the video port on
your PC.
• Connect the other end of the video cable to the video connector on your
touchmonitor.
• Secure the cable to your touchmonitor and PC by turning the screws on the
connector clockwise.
Video
cable
Video
port
Connections on underside
Ferrite bead
Female 15-pin
video
connector

2-10 Elo Entuitive Touchmonitor User Guide
STEP 2-Connecting the Serial Touchscreen Cable
• Connect the female end of the serial (RS-232) cable to the serial port on the
back of your PC.
• Connect the male end of the cable to the serial touchscreen connector on your
touchmonitor.
• Secure the cable to your touchmonitor and PC by turning the screws on the
connector.
Connections on underside
Serial
touchscreen
connector
Serial
touchscreen
cable

2-11
STEP 3-Connecting the Power Cable
Depending on where you live, you will use either the European or US/Canadian
power cable.
• Connect the female end of the power cable to the Brick power supply.
• Connect the Brick power supply into the power port on the touchmonitor.
To protect your equipment against risk of damage from electrical surges in the power
line, plug the brick supply’s power cord into a surge protector, and then connect the surge
protector to a grounded (three-pronged) AC electrical outlet.
• Power on your PC then your touchmonitor. After a brief pause the picture
should appear.
• The power can be turned on and off by the small white switch on the back of
the touchmonitor. The touchmonitor can also be turned on and off by
plugging and unplugging the power cable.
Optimizing the LCD Display
To ensure the LCD display works well with your computer, configure the
display mode of your graphic card to output 1024 x 768 resolution, and make
sure the timing of the display mode is compatible with the LCD display. Refer
to Appendix A for more information about resolution. Compatible video modes
for your touchmonitor are listed in Appendix C. Refer to Chapter 3 for more
information on adjusting your touchmonitor’s video characteristics.
Connections on underside
Power
cable
Power switch
Power

2-12 Elo Entuitive Touchmonitor User Guide
Installing the Driver Software
Elo TouchSystems provides driver software that allows your touchmonitor to
work with your computer. Drivers are located on the enclosed CD-ROM for the
following operating systems:
• Windows XP
• Windows 2000
• Windows Me
• Windows 98
• Windows 95
• Windows NT 4.0
Additional drivers and driver information for other operating systems (including
MS DOS, Windows 3.x, OS/2, Macintosh and Linux) are available on the Elo
TouchSystems web site at www.elotouch.com.
Your Elo touchmonitor is plug-and-play™ compliant. Information on the video
capabilities of your touchmonitor is sent to your video display adapter when
Windows starts. If Windows detects your touchmonitor, follow the instructions
on the screen to install a generic plug-and-play monitor.
Refer to the appropriate following section for driver installation instructions.

2-13
Installing the Serial Touch Driver for Windows XP,
Windows 2000
1
, Me, 95/98 and NT 4.0
N OTE : For Windows 2000 and NT 4.0 you must have administrator access rights to install the
driver.
1Insert the Elo CD-ROM in your computer’s CD-ROM drive.
If the AutoStart feature for the CD-ROM drive is active, the system
automatically detects the CD and starts the setup program.
2Follow the directions on the screen to complete the driver setup for your
version of Windows.
If the AutoStart feature is not active:
1Click Start > Run.
2Click the Browse button and locate the EloCd.exe program on the CD-ROM.
3Click Open, then OK to run EloCd.exe.
4Follow the on-screen directions to complete the driver setup for your version
of Windows.
1.To install Windows 2000 and Windows XP, you must use the "update driver"
method; you will not find a setup.exe file within the download.

2-14 Elo Entuitive Touchmonitor User Guide
Installing the Serial Touch Driver for MS-DOS and
Windows 3.1
To install the drivers for Windows 3.xand MS-DOS from Windows 95/98,
follow these steps:
1Insert the Elo CD-ROM in your computer’s CD-ROM drive.
2From DOS, type d:\EloDos_W31 to change to the correct directory on the
CD-ROM (your CD-ROM drive may be mapped to a different drive letter).
3Type INSTALL and press Enter to start the installation.
4Align the touchscreen.
If you need additional installation information, see Chapter 2 of the
Elo DOS and Windows Driver Guide found on www.elotouch.com .
To run the INSTALL program:
1Type INSTALL at the DOS prompt in the directory containing the driver
install files.
2INSTALL asks you to select the software to install.
3Choose d:\EloDos_W31 from the displayed list.
4INSTALL also asks you for the paths to use during installation. You may
select a path, or use the defaults. INSTALL creates directories as necessary,
and warns you if they exist.
If you are updating your software, you may wish to specify the paths containing
the earlier versions, and overwrite the obsolete files. All executable programs
are upward compatible. For a list of differences from each previous version of
the drivers, be sure to select "Differences from Previous Versions" during the
installation process.
INSTALL updates your AUTOEXEC.BAT file with the drivers you select.
INSTALL makes a copy of your original AUTOEXEC.BAT file, called
AUTOEXEC.OLD. If you already have Elo driver commands in your
AUTOEXEC.BAT file, they will be commented out.
When INSTALL is finished, it leaves a file called GO.BAT in the subdirectory
you specified. GO loads the touchscreen driver, runs the calibration program
ELOCALIB, and gives you some final instructions.
If you are using Windows 3.1, you will also align the touchscreen within
Windows 3.1 using the Touchscreen Control Panel.

3-15
CHAPTER
C HAPTER 3 O PERATION
About Touchmonitor Adjustments
Variations in video output and application will likely require you to adjust your
touchmonitor to optimize the quality of the display.
For best performance, your monitor should be operating in native resolution;
that is, 1024 x 768 at 60-75 MHz. Use the Display control panel in Windows to
choose 1024 x 768 resolution.
Operating in other resolutions will degrade video performance. For further
information, please refer to Appendix A.
All adjustments you make to the controls are automatically memorized. This
feature saves you from having to reset your choices every time you unplug or
power your touchmonitor off and on. If there is a power failure your
touchmonitor settings will not default to the factory specifications.