Elysee Indra User manual

User Manual
Bathtub Elysée Indra

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 2
Table of contents
Preface
Operating precautions
Table of contents
1. General arrangement drawing
2. Dimensions
3. Options et accessories
4. Technical specifications
DESCRIPTIF
COMPLIANCE
SAFETY INSTRUCTIONS AND WARNINGS
COMMISSIONING AND INSTRUCTIONS FOR USE
5. Operating instructions
5.1. Pushbutton switch hi/low frame
5.1.1. Rising up the lift table
5.1.2. Moving down the lift table
5.2. Bath setup
5.2.1. Locking of draining trap
5.2.2. Filling of the tub
5.2.3. Positioning of the patient in the bathtub
5.3. Draining of bathtub
6. Working position
7. Maintenance instructions
8. User manual (to be displayed next to the bathtub)
9. Technical settings instruction
10. Recommendation
11. Connection plans

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 3
Preface
Thank you for trusting and choosing the products Elysee Concept.
Before using your bathtub, please read entirely this manual. The information contained in this
manual is essential to the proper operation and maintenance of the equipment. It will help you to
best protect your investment and guarantee you a perfect operation of your equipment. Some
information contained in this manual also concerns your safety, they must be read entirely and
fully understood in order to avoid any risk of injury.
If the product has not been used in accordance with the instructions in this manual, Elysée
Concept will not be responsible for any problems.
For further information, please contact the Elysée Concept Sàrl offices. (First page of this
document).
Operating precautions
This equipment is intended to bathe residents, under the supervision of qualified medical staff and
in accordance with the indications defined in the user manual. Any other use could be the source
of dangerous situations. Read the precautions for use before.
Meaning: safety warning. In the event of non-compliance with this directive, the user or operator expose
himself to a risk of injury.

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 4
1. General arrangement drawing
Elysée INDRA
1 Aromatherapy container *
4 Height-adjustable chassis control
5 Bathwater tempera ture display *
6 Tap securing device and pre-filling control *
7 Emptying and overflow opening and closing control
8 Wa ter outlet plug
9 CONCEALED thermostati c locking mi xer
10 CONCEALED ri nsing shower
11 Insert for Perspex footrests
13 Stainless-steel grips handle
14 Head res t
15 Disinfection sta tion *
16 Soap/essential oils dispenser *
17 Height-adjustable chassis legs
18 Cascade filling
19 Disinfection container *
* Optional
2 Starting of hydromassage *
1 push = continuous jet (red LED on)
2 pushes =alternati ve jet (red LED on-lighting)
3 pushes =stop (LED off)
Starting of Air jet *
1 push—continuous jet (red LED on)
2 pushes = wave effect (red LED on-lighting)
3 pushes : stop (LED off)
Starting of chromotherapy *
1 push = loop light cycle (red LED on)
2 pushes = colour fixing (red LED on-li ghting)
3 pushes = s top (LED off)
Starting of PRIMA balneo system * (Air)
1 push = ON
2 pushes—OFF
Only operates if the minimum water level is reached
20
SNOEZELEN PROGRAMME - CHOOSE THE OP TIONS
1 + 2 + 3 + 20 + 22
3 Semi-automatic disinfection *
- Fill the bath up to the required minimum wate r
le vel (balneotherapy level)
- Press the control button for 5’’ (LED continuousl y
on)
- To s top, press the control (LED off)
Red LED on —> fill the container with disinfectant
Automatic disinfection (Flash) *
- Green LED on when bath is completel y empty (10
min. ti me dela y)
- To a ctivate manually, press the control for 5
seconds (LED on)
22 Chromothera py devi ce by mul ti colour proje c-
tor *
2 X 7 colour LEDs for PRIMA chromotherapy *
21 Wa ter balneotherapy suction strainer *
20 Dream musi c *
9
Filling
Shower
Hot
water
Cold water
REMINDER—Read the directions for use
carefull y before use

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 5
2. Dimensions

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 6
3. Options & accessories
Ref
Description
2864
Pre-filling system
11222
Pre-filling system with t° display
430
Headrest with suction grip
8672
Fixed headrest
1561
Suction grip with safety - Vitility 50 cm
10442
Suction grip with safety - Roth Mobeli 21 cm
2708
Suction grip with handle
2098
Soap and/or essential oils dispenser
854
Suction table
10804
Transparent Perspex footrest (4 in 1)
Remote control for height-adjustable chassis
BALNEOTHERAPY - OPTIONS
13371
Prima Air balneotherapy & Chromotherpay ( colour light therapy)
Prima Water balneotherapy (with Prima colour therapy) + instant
disinfection
3386
Ely'Lisse + balneotherapy
10423
Ely'Reva balneotherapy + instant disinfection
13082
Ely'Well + instant disinction
10395
Ely'Zen balneotherapy + instant disinfection
Ely'Zen/Reva balneotherapy + semi-automatic disinfection
* Hydromassage with massage hose for Ely'Reva, Ely'Zen and Ely'Zen/Reva
Power Jet balneotherapy + instant disinfection
371
UV disinfection on Ely'Zen and/or Reva balneotherapy system
NATURAL THERAPIES
382
Aromatherapy
12988
Colour therapy with Ely'Lisse balneotherapy and colour pause
10421
Colour therapy with Ely'Reva and Ely'Well balneotherapy and colour pause
374
Colour therapy with balneotherapy - Ely'Zen and Ely'Zen/Reva + colour
pause
378
Colour therapy with colour pause for baths without balneotherapy
Phytotherapy
9872
Dream music
DESIGN- Screen printing
See catalogue
DISINFECTION
13364
Trigger-operated disinfection system (KIWA)
Protective box for disinfection equipment
11109
(Option for article 11108 - only)

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 7
4. Technical specifications
DESCRIPTION
Bathtub, made of a metal hi/low frame powered by electrical actuators (24 V) operating at a range of min. 156/max.
456 mm, supporting a polyester tank allowing use of an active or passive transfer system. An optional emergency
battery is available.
The metallic frame is completely covered with side panels
The Stainless steel IP 67control button for the hi/low frame are located on the control panel. The metal frame stands
on the floor with two self-supporting feet, each with two height adjustable feet.
The frame does not exceed bath space
Under frame is fully cleared in the lower portion of the bathtub at a minimum height of 156 mm (lowest frame
position)
From one foot to the other, it allows access to a transfer system. As well as the maintenance or any technical
intervention is facilitated by this space
Inner and bottom frame are fully treated against corrosion
The surface of the polyester tank, super resistant, ease cleaning (Sanitary gel coat)
Two molded armrests, each equipped with a support handle (painted or stainless steel), will provide great stability to
the patient / resident
The tub has an ergonomically shape with a length of 1900 mm and a width of 780 mm - for internal dimensions: see
attached drawing
The tub rounded design is made without any protruding edge and is formed of an anatomical seat and a disbursement
at the bottom of the tub which allows the elevation of the legs and optimal safety for the patient / resident. The tub is
also equipped with a molded anatomic headrest and can be equipped with an additional comfort headrest with
suction cup (optional) or to be fixed (option)
The bath can be equipped with a removable plexi footrest and adjustable in 4 positions (option)
The color of the tub is white. The panels are white basic but can be covered with a solid colors to choose from
77colors or a standard serigraphy or to tailor-made (optional)
The tank is equipped with an overflow –draining by pull device without chain
The working height varies between 730 and 1030 mm
The bath has a built-in thermostatic faucet system with hand shower (locking of safe t° - burn protection) - 1/2 "
The bath can be fitted with a pre-filling system for securing the taps with or without t ° display (option)
Electrical controls are protected against water and any other liquid and it operates under low voltage 24V according
to medical safety guidelines.
The bathtub and the operating controls works at 24 Volts low voltage, according to medical safety guidelines
Compatible with all transfer systems
ø50 mm draining tap
COMPLIANCE
Your Elysée Indra bathtub, equipped with a lifting table (height-adjustable frame), has a type IIA
certificate of conformity and is CE marked. This means that its design and construction comply
with the MACHINES directive of the EEC Council
SAFETY INSTRUCTIONS AND WARNINGS
Do not use the bathtub if you do not understand this guide
To ensure the safe use of the bath, please read this guide carefully, especially the following safety
instructions, before installing, using, or maintaining this equipment.
Make sure you have received all the instructions and read them carefully before use.

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 8
If the information in this guide is not completely understood, contact your official dealer or Elysée Concept
SàRL. Failure to follow the warnings in this guide and instructions for use of the various options and
accessories could result in injury.
Keep this manual safe and refer to it as needed. The contents of this manual are subject to change without
notice to users.
The bath can only be accessible under the supervision of a person with authority
COMMISSIONING AND INSTRUCTIONS FOR USE
The Elysée Indra must be installed by an authorized technician
DO NOT stir up the bathtub
NO NOT stay underneath the tub when descending
DO NOT pull the shower abruptly
DO NOT leave the shower submerged in the bath
DO NOT leave anything under the bath
The bath is equipped with a 38° water t° locking system, if this device were to be removed it would be
entirely the responsibility of the purchaser
DO NOT use electrical equipment near the bath or in the bath
Regularly test the t° of water using an independent thermometer and check the bath t° before the patient
enters the water
ALWAYS do a daily check before bathing
ALWAYS make sure the patient is safe as they enter and exit the bath (use grab bars, adjust bath height,
etc.)
The bath must be cleaned and disinfected after each use according to the disinfection instructions (provided
with the bath at the delivery)
Any disinfectant and cleanser should be used according to the recommendations for use and safety
mentioned on the bottle or on the disinfection leaflet
A weekly safety check shall be performed to ensure that all pipes, hoses, fittings and attachments are in
good condition. If the bath is equipped with a balneotherapy, activate the system to avoid seizure.
Keep all components of the bathtub clean and dry
Annual bathtub maintenance will be conducted by an approved technician
5. Operating instructions
The ELYSEE Indra bathtub equipped with the lift table is a bathtub that offers unique comfort for
patients and caregivers. It’s destined for washing people. The lift table can only be used in
combination with the ELYSEE bath. Any other use is ABSOLUTELY PROSCRIBED.

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 9
5.1.Pushbutton switch hi/low frame
FIG I.: Pushbutton switch
5.1.1. Rising up the lift table
Refer to Figure I.
Press the rise pushbutton (upper A button) located on the bath shelf next to the taps of the
ELYSEE Indra bathtub. The lift table continues to rise as long as the push-button pressure is
maintained. The electric rise control of the lift table will automatically stop the rise as soon as the
cylinders arrive at the end of the race. (Maximum height under bath 453 mm and minimum height
153 mm)
When bathing, make sure that no obstacles are present on the bath’s climb path, either in the
lower area of the bath, (transfer system) or around the bath. If an object or anything was on the
way, the operator/resident would be at risk of injury and the bathtub could be damaged
5.1.2. Moving down the lift table
Refer to Figure I
Press the descent pushbutton (lower B button) located on the bath shelf next to the taps of the
ELYSEE Indra bathtub. The lift table continues to descend as long as the push-button pressure is
maintained.
The electric descent control of the lift table will automatically stop the descent as soon as the
cylinders arrive at the end of the race.
When descending the bathtub, the operator must ensure that there is nothing to prevent the
equipment from descending. If an object or anything clogged the bathtub during the descent, the
operator/resident would be exposed at risk of injury and the bathtub could be damaged.
Resident or Operator Instruction: Never sit on the side or end of the bathtub
Rising up the lift table - B
Moving down the lift table - A

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 10
5.2. Bath setup
5.2.1. Locking of draining trap
Refer to Figure II
Turn the overflow cap cover to seal the draining tap before turning the water on.
FIGURE II : overflow cap cover and draining tap
5.2.2. Filling of the tub
Before filling the bath, ensure that the temperature is blocked at 38°. If not, turn the selection
button to the desired temperature and press the button. (Anti-burn safety) (See Figure III)
WARNING your bath is equipped with a t° blockage, making impossible to set the t° of the water
beyond the anti-burn safety (38°). If you would like to change this option, please contact the
Authorized Technician.
For maximum safety, it is recommended that you check the water temperature with a
thermometer placed under the water jet, REGULARLY.
Then, to activate the water flow, select the flow through the shower (see Figure III) by turning the
handle towards the shower or by the cascade filling system (see Figure III) by turning the handle
towards the opposite side. The maximum temperature is 38° (position A) - if it is too hot, turn the
joystick to the left (temperature less than 38°).
Fill the tub with the desired amount of water, then install the patient. An automatic overflow
(Figure II) will prevent any overflow of the bathtub.

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 11
FIGURE III: Integrated thermostatic tap
5.2.3. Positioning of the patient in the bathtub
Refer to Figure I
Adjust the tub to the lowest height to facilitate the patient’s entry into the bath.
Install the patient in the ELYSEE Indra bathtub.
Adjust the tub to the desired height to wash the patient in ergonomic position without pain
or risk of back pain.
To prevent from tipping, avoid standing up in the bathtub
5.3. Draining of bathtub
When the bath is finished, just turn the overflow cap cover on the right to unseal the draining tap
6. Working position
The preferred position of the bath is to be adjusted by the staff for each bath thanks to the hi/low
frame and depending of the size of the care users.
The bathtub Elysée Indra offers full access all around the bath, as far as the space around the
bathtub allows it. The entire periphery of the lift table has a clearance to allow the feet to be
placed without the risk of pinching.
Position A
Hot water
Cold water

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 12
7. Maintenance instructions
For an optimal maintenance, it is strongly recommended that you consult the disinfection manual
provided with your bath
Once the bath is done, adjust the height of the bath to allow ergonomic working conditions by
using the control buttons see Chapter 5.1.Push-button switch hi/low frame
Rinse and clean the inside of the bathtub, using the shower head.
Do not clean the bathtub with abrasive products or sponges
Preferably use the disinfection product Ely'a surfed Safe, available in the range of disinfection
products Elysée Concept
If the bath is equipped with a balneotherapy system, start the disinfection or let the automatic
system start by itself and complete the cycle
Protective gloves and glasses should always be worn when handling
concentrated disinfectant products. Avoid contact of the cleaning product with
the skin or eyes. In case of contact with the product, rinse thoroughly with fresh
water. In case of irritation contact a doctor.
Follow carefully the instructions on the product.
When using bath additives, make sure they are sufficiently diluted with water
before putting them in the bathtub. After a bath containing bath additives, the
bathtub should be rinsed with clear water.
Once a year, it is recommended that you maintain your Elysee bath by a qualified technician.
The valves used for KIWA certification must be replaced every 10 years
(as per WB1.4G Standard –www.infodwi.nl)

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 13
8. User manual (to be displayed in the bathroom)
-Turn the overflow cap cover to seal the draining tap.
-Turn on the water at appropriate t°
-Install the patient in the ELYSEE Indra bathtub
-Adjust the height of the tub to obtain an ergonomic working position.
-Once the bath is done, turn the overflow cap cover on the right to unseal the draining tap and let the
water evacuate
Recommended use
To avoid tipping, avoid standing in the bath
It is strictly forbidden to insert a foreign object between the ground and the bathtub during
the descent of the hi/low frame.
It is strictly forbidden to place a foreign object on the trajectory of the bathtub when rising
Cleaning
Once the bath is finished, it is mandatory to rinse and clean the inside of the bathtub with a cleaning and
disinfectant product.
Do not clean the bathtub with abrasive products or sponges. Preferably use the disinfection product Ely'a
surfed Safe.
In the case the bathtub is equipped with a balneotherapy rinsing system, be sure to respect the required
timing to finalize the disinfection process (+/- 10 minutes for all models with a “flash” disinfection
system, +/- 18 minutes for models with an automatic disinfection system) before installing a new patient
in the bathtub for the next bath.
In the case of a bathtub with a balneotherapy system, be sure to perform shock chlorination on a weekly basis.
(Refer to disinfection note)
Gloves and glasses should always be worn when handling concentrated
disinfectant products. Avoid contact of the cleaning product with the skin or eyes.
In case of contact with the product, rinse thoroughly with fresh water. In case of
irritation contact a doctor.
Follow carefully the instructions on the product.
When using bath additives, make sure they are sufficiently diluted with water
before putting them in the bathtub. After a bath containing bath additives, the
bathtub should be rinsed with clear water

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 14
9. Technical settings instruction
Once the ELYSEE Indra bathtub and lift table are set in position and height, no adjustment is
required.
10. Recommendation
If your Elysée Indra bath is equipped with natural therapies or external disinfection devices,
please refer to the Elysée Ad-hoc instructions provided with the bath.
12. Connection plans

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 15

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 16

User Manual
Bathtub ELYSEE Indra
jeudi 7 février 2019 - 17
IN CAS OF FAILURE –instruction for technicians only
PROBLEMS
SOLUTIONS
Tap
Pressure failure
1. Clean filter
Hot water failure
1. Replace cartridge
2. Control filter
Lift
Do not rise
1. Check power supply
2. Check connection in the electrical box
3. Check switch button
Do not go down
Idem
Do not rise in a synchronized way
1. Bring the tub in the lower position
2. Simultaneously press the climb and descent button
3. Wait for the bip
4. Rise the tub
Body
Side panels loose
1. Proceed with a tightening
Balnéo
Won’t start
1. Check the fuse
2. Check motor
3. Check push button
4. Check if minimum water level is reached
T° display don’t work
1. Replace battery
Chromothérapy
Won’t start
1. Check push button
The customer will refuse to order from a third party person or company, any repair regarding the bathtub covered by the warranty.
The intervention of any person non-certified by Elysée Concept Sàrl excludes her from any responsibility and allows her to
suspend immediately the guarantee.