emerio CFH-212922.1 User manual

- 1 -
Content –Inhalt –Contenu –Contenuto
Instruction manual –English .....................................................................- 2 -
Bedienungsanleitung –Deutsch .............................................................. - 12-
Mode d‘emploi – Français ....................................................................... - 23 -
Manuale d'istruzioni –Italiano ................................................................ - 34-

- 2 -
Instruction manual –English
SAFETY INSTRUCTIONS
Before use make sure to read all of the below instructions in
order to avoid injury or damage, and to get the best results
from the appliance. Make sure to keep this manual in a safe
place. If you give or transfer this appliance to someone else
make sure to also include this manual.
In case of damage caused by user failing to follow the
instructions in this manual the warranty will be void. The
manufacturer/importer accepts no liability for damages
caused by failure to follow the manual, a negligent use or use
not in accordance with the requirements of this manual.
1. This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved.
2. Children shall not play with the appliance.
3. Cleaning and user maintenance shall not be made by
children without supervision.
4. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
5. Before inserting the plug into the mains socket, please
check that the voltage and frequency comply with the
specifications on the rating label.
6. Disconnect the mains plug from the socket when the
appliance is not in use and before cleaning.
7. Ensure that the mains cable is not hung over sharp edges
and keep it away from hot objects and open flames.
8. Do not immerse the appliance or the mains plug in water
or other liquids. There is danger to life due to electric shock!
9. To remove the plug from the plug socket, pull the plug. Do
not pull the power cord.
10. Do not touch the appliance if it falls into water. Remove the
plug from its socket, turn off the appliance and send it to
an authorized service center for repair.

- 3 -
11. Do not plug or unplug the appliance from the electrical
outlet with a wet hand.
12. Never attempt to open the housing of the appliance, or to
repair the appliance yourself. This could cause electric
shock.
13. Never leave the appliance unattended during use.
14. Do not use the appliance for other than intended use.
15. Keep the appliance away from damp, and protect from
splashes.
16. Do not store or operate the appliance in the open air.
17. Keep the appliance in a dry place for storage, inaccessible
to children (in its packaging).
18. Never put fingers or any other objects through the fan
guards when the fan is running.
19. Never operate the product without the fan guards in place,
as serious personal injury may result.
20. The appliance must be assembled completely before use.
21. Watch out for long hair! It can be caught in the fan owing
to the air turbulence.
22. Do not point the air flow at people for a long time.
23. Ensure that the fan is switched off from the supply mains
before removing the guard.
24. Do not use the fan in a wet room, such as a bathrrom or
laundry.
25. Do not use the fan in the presence of flammable substances
or vapour such as alcohol, insecticides, petrol, etc.
26. Do not use the mains plug to start and stop the fan.
27. Do not pull the supply cord or place it near a heat source.
Always unwind the cord completely to avoid overheating.
28. Do not attempt to move your fan whilst it is operating.
29. Always use the switch on the control panel to start and stop
the fan.
30. Always keep a clearance of at least 200mm from walls,
furniture and curtains.
31. Improper installation may result in the risk of fire, electric
shock and/or injury to persons.
32. Keep blinds/curtains closed during the sunniest part of the
day.

- 4 -
CFH-212922.1 EN
PARTS DESCRIPTION
1. Front grille
2. Rear grille
3. Control panel
4. Motor unit
5. Power cord
6. Motor connector
7. Height adjustment pipe
8. Standing shaft
9. Base
10. Remote control
11. Remote control base
12. Decorative cap

- 5 -
CONTROL PANEL
1. On/off button
2. Swing button
3. Feel mode button
4. Sleep mode button
5. Timer button
6. Speed decrement button
7. Speed increment button
8. Sleep mode indicator icon
9. Feel mode indicator icon
10. Swing indicator icon
11. Digital display for speed
12. Digital display for timer
LOCATING YOUR APPLIANCE
-The fan must always be placed on a flat stable surface.
-Do not locate the fan where furniture or other objects can obstruct the air flow.
ASSEMBLING INSTRUCTIONS
** Please assemble correctly by the following order when using.
Stand assembly
1. Loosen the four screws from the base. (fig.1)
2. Loosen the locking bolt (a), ring washer (b) and washer plate (c) from the bottom of the standing shaft. (fig.2)
3. Attach the standing shaft onto the base and fix firmly with the four screws. Tighten back the locking bolt,
ring washer and washer plate to the bottom of the standing shaft. (fig.3)
4. Loosen the height adjustment knob (d) and the three screws (e) at the bottom of the height adjustment pipe.
Remove the height adjustment pipe out of the standing shaft. (fig.4)
5. Put the decorative cap (f) on the base through the standing shaft. (fig.5)
6. Insert back the height adjustment pipe and fix with the three screws. Pull the pipe to your desired height
and fix with the height adjustment knob.
fig.1 fig.2 fig.3 fig.4 fig.5

- 6 -
Motor unit assembly
1. Loosen the stopper screw (g), tilt head adjustment bolt (h), washer (i) and fixing nut (j) from the motor
connector. (fig. 6)
2. Slide the motor unit into the slot of the motor connector. Align the holes on the connector and the motor
unit, insert the tilt head adjustment bolt, washer and fixing nut, and then use a wrench to fasten them firmly.
Tighten back the stopper screw. (fig. 7)
3. Loosen the cable clamp screw (k) on the motor connector. Place the power cord (l) through the cable clamp
(m). Then fix the screw back. (fig. 8)
Note: The length of the power cord between the motor unit and the cable clamp cannot be too short. Make
sure there is enough space in between so that the fan head can operate smoothly for swing function.
fig.6 fig.7
fig.8
Make sure the top point of
the bolt is correctly aligned
with the groove in the hole.

- 7 -
Rear grille assembly
1. Remove the black protective sleeve (n) from the motor shaft (o). (fig.9)
2. Loosen the four screws (p) from the front side of the motor unit. (fig.10)
3. Attach the rear grille onto the motor unit by aligning the screw holes on the grille and the front side of the
motor unit. Tighten back the four screws. (fig.11) Make sure the screw hole (q) on the rear grille is at the
bottom. (fig.12)
fig.9 fig.10
fig.11 fig.12
Fan blade assembly
1. Loosen the screw (r) from the fan blade (s). (fig.13)
2. Insert the center of the fan blade (align with the groove/flat part (t) of the motor shaft) into the motor shaft
and tighten the screw on the middle of the fan blade. (fig.14)
fig.13 fig.14

- 8 -
Front grille assembly
1. Put the hook (u) of the front grille on the top of the rear grille. (fig.15)
2. Attach the front grille to the rear grille and then close the guard clips (v). (fig.16)
3. Secure the front and rear grilles by fastening the fixing screw with nut (w). (fig.17)
fig.15 fig.16
fig.17
REMOTE CONTROL
1. Speed increment button
2. On/off button
3. Swing button
4. Speed decrement button
5. Sleep mode button

- 9 -
This unit has a remote control. One piece of CR2032 battery is to be installed. The functions of the remote
control buttons are the same as of the buttons on the control panel. Remember to remove the plastic isolation
piece inside the battery cover when you use it for the first time.
Remote control pairing
Important: By default, the remote control in the box is paired already with the fan with which is it supplied.
However, if you lost the remote control and purchase a new one, then please pair the remote control with the
fan before use.
Steps to pair:
1. Ensure that the battery is placed inside the remote control.
2. Plug in the appliance.
3. Press the on/off button on the remote control 4 times and hold it in the position till the beep sound is heard
on the 4th time.
4. Once the beep sound is heard the remote control is paired with the fan.
Base mounting of the remote control
1. Drill two holes on the wall according to the holes (A) on the remote control base.
2. Insert the two plastic anchors (B) in the holes on the wall, attach the remote control base onto the plastic
anchors, and then insert the two screws (C) through the holes to fix the base.
3. Press the remote control into the base. Rotate the remote control by 90 degrees to have it fixed in place.