Emerson ACF552ORB00 User manual

READ AND SAVE THESE INSTRUCTIONS
Part No. F40BP74610000 Form No. BP7461
Model No.: ACF552
132 cm (52”) Ceiling Fan
Owner's Manual
ACF552ORB00
ACF552WW00
Models
Net Weight: 9.8 Kg.
MOST IMPORTANT: READ THESE INSTRUCTIONS
THE FAN MUST BE INSTALLED BY A LICENSED ELECTRICIAN.
(The warranty on this fan will be void if the appliance
is not installed by a licensed electrician).
This ceiling fan is imported by MyFan as an agent for the USA design owners’ and can provide
after sales service for this product if required. Contact can be made by phone, fax or email
during normal trading hours. Copies of owner’s manuals for each model can be found on our
web site.
Phone: [phone]
[email protected]
www.myfan.com.au
VERANDAH™

2Model No.: ACF552
WARNING To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at fuse box and lock to prevent power from being switched
on accidentally. When the fuse box cannot be locked, securely fasten a warning device, such as a tag, to the
fuse box.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to
the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan
without blades.
2. All wiring must be in accordance with AS/NZS 3000 “The Wiring Rules”. The ceiling fan must be grounded as a
precaution against possible electrical shock. Electrical installation should be made or approved by a licensed
electrician.
3. The ceiling fan hanger bracket must be securely mounted and capable of reliably supporting at least 40kg.
4. The downrod furnished with the fan provides the minimum recommended floor to fan blade clearance for a
2.4 m ceiling.
5. The fan must be mounted with the fan blades at least 2.1 meters from the floor to prevent accidental contact
with the fan blades.
6. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
NOTE: This fan is not suitable for use with solid-state speed controls.
WARNING: This product is designed to use only those parts supplied with this product and/or any accessories
designated specifically for use with this product by My Fan Pty Ltd. Substitution of parts or accessories not
designated for use with this product by My Fan Pty Ltd. could result in personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
WARNING: This product is suitable for use in wet locations when installed with approved protection on electrical
circuits.
WARNING: This fan MUST be installed with an easily accessible isolating device to disconnect all poles of the
fan from the main supply.
WARNING
DIY MUST BE INSTALLED
BY A LICENSED
ELECTRICIAN

3
1. Unpack the items carefully to avoid damage to any
of the components.
Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description,
refer to the exploded view illustration.
a. Fan motor assembly
b. One ceiling cover
c. One coupling cover
d. One switch cup cover
e. One switch cup
f. Five fan blades
g. Five fan blade holders / flanges
h. One hanger bracket
i. One hanger ball/downrod assembly
j. One canopy seal pad
k. One loose parts bag, containing:
1. One clevis pin
2. One hairpin clip
3. Sixteen M5 x 6mm washer head blade
screws
4. Two #8-32 x 1-1/4" threaded studs
5. Two #8 external tooth lockwashers
6. Two #8-32 knurled knobs
7. One M6x14mm pan head screw with
lockwasher (spare)
8. One M4x12mm flat head screw (spare)
9. One M4x10 serrated pan head screw
(spare)
10. One balancing kit
Model No.: ACF552
Tools Needed for Assembly
One Phillips head screwdriver
One stepladder
One small blade screwdriver
One wire stripper
The fan must be installed by a licensed electrician.
WARNING
THIS FAN IS SUITABLE FOR WET LOCATIONS SUCH AS PORCHES, PATIOS, AND DECKS.
USE ONLY WITH LIGHT KITS MARKED SUITABLE FOR USE IN WET LOCATIONS.
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step is completed, place a
check mark in the box. This will insure that all steps have been completed and will be helpful in finding
your place should you be interrupted.
Do not install or use fan if any part is damaged or
missing, call:
1300 469 326
WARNING
!
NOTE: Intermixing blades between fans can
cause excessive wobble. Keep blades in original
sets of five.
a. Fan Motor Assembly
d. Switch Cup Cover
h. Hanger Bracket
i. Hanger Ball/Downrod
Assembly
k. Loose Parts Bag
g. Fan Blade Holders/Flanges
j. Canopy Seal Pad
f. Fan Blades
c. Coupling Cover
b. Ceiling Cover
e. Switch Cup
MATERIALS
Wiring and connectors must be of type required by
local regulations. The minimum wire would be a
3-conductor (2-wire with ground).
This manual is designed to make it as easy as possible for your Electrician to assemble and install
your ceiling fan.

4Model No.: ACF552
How to Put This Ceiling Fan Together
1. Remove the hanger ball by loosening the setscrew
in the hanger ball until the ball falls freely down the
downrod (Figure 1). Remove the pin from the
downrod, then remove the hanger ball. Retain the
pin and hanger ball for reinstallation in Step 6.
2. Separate, untwist and unkink the four 2 m. (80”)
motor leads/connector. Route the motor lead
wires/connector through the downrod.
3. Remove the setscrew from the motor coupling.
Insert the downrod into the motor coupling. Align
the clevis pin holes in the downrod with the holes in
the motor coupling. Install the clevis pin and secure
with the hairpin clip (Figure 2). The clevis pin must
go through the holes in the motor coupling and the
holes in the downrod. Be sure to push the straight
leg of the hairpin clip through the hole near the end
of the clevis pin until the curved portion of the
hairpin clip snaps around the clevis pin. The hairpin
clip must be properly installed to prevent the clevis
pin from working loose. Pull on the downrod to
make sure the clevis pin is properly installed.
4. Reinstall the setscrews in the motor coupling and
tighten securely while pulling up on the downrod.
(Figure 2).
NOTE: The setscrews must be properly installed
as described above, or fan wobble could result.
PIN
HANGER
BALL
SETSCREW
DOWNROD
Figure 1
SETSCREW
CLEVIS
PIN
DOWNROD
HAIRPIN
CLIP
MOTOR COUPLING
SETSCREW
CLEVIS PIN
HAIR PIN
CLIP
CLEVIS
PIN
STRAIGHT
LEG OF
CLEVIS PIN
MOTOR COUPLING
Figure 2
DOWNROD COUPLING
COVER
GROMMET
CEILING COVER
Figure 3
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrews securely
tightened. Failure to verify that the pin and setscrews
are properly installed could result in the fan falling.
WARNING
!
5. Make sure the grommet is properly installed in the
coupling cover, then slide the coupling cover on the
downrod until it rests on the motor housing. Place
the ceiling cover over the downrod. Be sure that
the ceiling cover and the coupling cover are both
oriented correctly (Figure 3).
6. Reinstall the hanger ball (Figure 4) on the downrod
as follows. Route the motor leads/connector
through the hanger ball. Position the pin through
the two holes in the downrod and align the hanger
ball so the pin is captured in the groove in the top
of the hanger ball. Pull the hanger ball up tight
against the pin and securely tighten the setscrew in
the hanger ball. A loose setscrew could create fan
wobble.
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
WARNING
!
HANGER
BALL
SETSCREW
PIN
DOWNROD
CEILING
COVER
Figure 4

5Model No.: ACF552
8. Turn fan assembly upside down in preparation for
mounting fan blade assemblies.
9. Remove and discard the five shipping spacers and
screws from the motor hub (Figure 5).
10. Mount a blade flange to fan blades using three
M5 x 6mm washer head blade screws (Figure 6).
Be sure the raised edge of the fan blade is facing
up. Repeat this procedure for the remaining four
blades and fan blade flanges.
NOTE: Take care not to scratch fan housing when
installing blades.
SHIPPING
SPACER (4)
SHIPPING SPACER
SCREW (4)
N
O
T
E
!
R
e
m
o
v
e
R
u
b
b
e
r
P
a
c
D
i
s
c
a
r
d
B
e
f
o
r
e
I
n
s
t
a
ll
a
t
i
o
MOTOR HUB
Figure 5
FAN BLADE FLANGES (5)
M5 x 6mm WASHER
HEAD BLADE SCREW (3)
FAN BLADE (5)
Figure 6
To reduce the risk of personal injury, do not bend the
blade holder when installing the blade holders,
balancing the blades or cleaning the fan. Do not
insert foreign objects in between rotating fan blades.
WARNING
!
13. Remove one M4 x 10mm serrated pan head
screw from the lower housing adapter (reserve
for later use). Loosen the other two screws to
assemble the switch cup cover to the lower
housing adapter (Figure 7).
14. Install the switch cup cover onto the lower
housing adapter by aligning the two key holes in
the switch cup cover with the two screws
loosened in Step 13. Rotate the switch cup cover
clockwise to engage the loosened screws into the
two key hole slots. Align the third hole in the
cover with vacant threaded hole on the lower
housing adapter. Re-install the screw removed in
Step 13 into the aligned holes. Securely tighten
all three screws (figure 8).
NOTE: Make sure wires are not pinched between
switch cup cover and lower housing adapter.
BLADE ASSEMBLY
M6 x 14mm CAPTIVE
SCREW WITH
LOCKWASER
REMOVE ONE M4 x 10mm SERRATED
PAN HEAD SCREW
LOWER HOUSING
ADAPTER
Figure 7
M4 x 10mm
SERRATED PAN
HEAD SCREW (3) ROTATE SWITCH CUP
COVER CLOCKWISE
SWITCH CUP
COVER
Figure 8
12. The fan blade holders have an interlocking
feature that must be fully engaged before
tightening the screw. Make sure all the holders
are properly engaged and then tighten the holder
screws. If one of the fan blade holders does not
seat properly on the motor hub, loosen the
adjacent holder screws, re-engage and reseat
the holders, then tighten the screws again.
7. The motor lead wires will require shortening if
using a 1.5 m. or shorter downrod. The fan comes
with blue, brown, orange and green/yellow motor
leads that are 2 m. (80") long. Measure up
approximately 15 cm. (6") above top of hanger
ball/downrod assembly and cut off the excess lead
wire. Strip back the wire insulation as follows:
A. Green/yellow wire - 10 mm. from the cut end.
B. Blue/brown/orange - 8 mm. from the cut end.
Twist all wire tips a minimum of 2 turns.
11. Loosely attach one blade assembly to the motor
hub using two M6 x 14 captive pan head screws
with lockwashers installed on the fan blade
holders. Make sure the screws are NOT
tightened. (Figure 7.) Repeat this procedure for
other four blade assemblies.

6Model No.: ACF552
15. Connect the ceiling fan wire connector to the
switch cup wire connector (Figure 9).
16. Remove the M4 x 12mm flat head switch cup
cover screws (reserve for future use) (Figure 9).
NOTE: Make sure all wires and connector are
tucked under the switch cup and not pinched
between switch cup and switch cup cover.
17.Position the switch cup onto the switch cup cover,
aligning each of the the three holes. Attach the
switch cup by reinstalling the three screw
previously removed in Step 15 (Figure 10).
M4 x 12mm FLAT
HEAD SCREW (3)
SWITCH CUP
SWITCH CUP
COVER
WIRE
CONNECTORS
Figure 9
SWITCH
CUP
M4 x 12mm FLAT
HEAD SCREW (3)
Figure 10
Electrical and Structural
Requirements
This new ceiling fan will require a grounded electrical
supply line of 240V, AC, 50Hz, 10 amp circuit.
If this fan is to replace an existing ceiling light
fixture,turn electricity off at the main fuse box at this
time and remove the existing light fixture.
The hanger bracket must be securely anchored and
capable of withstanding a load of at least 40kg.
Figure 11 depicts typical structural configuration that
may be used for securely mounting the fan.
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with AS/NZS 3000 "the Wiring
Rules" and the ceiling fan must be properly grounded
as a precaution against possible electrical shock.
WARNING
Disconnect electrical supply and test before you
touch!
All wiring must be in accordance with AS/NZS 3000
“The Wiring Rules”.
The warranty on this fan will be void if the appliance is
not installed by a licensed electrician.
WARNING
The ceiling fan is 220-240V 50Hz Class I appliance
and will require an earth. Figure 11 depicts different
structural configurations that may be used for
securely mounting the fan.
CEILING
CEILING
JOISTS
50 x 200mm
TIMBER BATTEN
BETWEEN JOISTS
CEILING JOIST
Figure 11

7Model No.: ACF552
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
WARNING
How To Wire Your Ceiling Fan
3. Pull the branch circuit supply wires through the
center of the canopy seal and position as shown
(Figure 14). Carefully lift the fan and seat the
hanger ball/downrod assembly onto the hanger
bracket that was just attached to the ceiling joist
(Figure 13). Be sure the groove in the ball is lined
up with tab on the hanger bracket (Figure 14).
TWO
SCREWS
HANGER
BRACKET TAB
TERMINAL
BLOCK
CANOPY
SEAL PAD
Figure 13
HANGER BRACKET
HANGER BALL/
DOWNROD
ASSEMBLY
THREADED STUD (2)
BRANCH CIRCUIT
SUPPLY WIRES
Figure 14
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
WARNING
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
WARNING
2. Securely attach the canopy seal pad and hanger
bracket to the ceiling joist using the two screws
(Figure 13).
1. Place the canopy seal pad flat against the ceiling
and position the hanger bracket into the canopy
seal pad (Figure 13).
FLOOR
CEILING
AT LEAST
2.1 METER
Figure 12
The fan must be hung with at least 2.1 meters of
clearance from floor to blades (Figure 12).
WARNING
The hanger bracket must be securely mounted to the
ceiling joist and capable of supporting at least 40 Kg.
WARNING
How To Hang This Ceiling Fan
MAIN FUSE BOX
Figure 15
NOTE: CEILING COVER AND FAN WIRES OMITTED FOR CLARITY.
1. Turn off the branch circuit electricity at the main
fuse box (Figure 15).
2. Plug the hanger ball green/yellow ground wire
connector into the hanger bracket green/yellow
ground wire connector. Locate the fan motor
green/yellow wire and combine with the hanger
bracket green/yellow wire. Pair the leads and twist
the bare wires together a minimum of three turns
and insert into the previous terminal block location
marked (Figure 16). Securely tighten the
termninal block screw with a small flat blade
screwdriver.
3. Securely connect the fan motor blue (Neutral) wire
to the hanger bracket terminal block marked N
with a small flat blade screwdriver. (Figure 16).
4. Securely connect the fan motor brown (active) wire
to the hanger bracket terminal block marked L
with a small flat blade screwdriver. (Figure 16).
5. Securely connect the fan motor lighting orange
(active) wire to the hanger bracket terminal block
marked L1 with a small flat blade screwdriver.
(Figure 16).
6. Check to see that all terminal block connections
are tight and that no bare wire or wire strands are
visible at the terminal block.
Fan Connections To Terminal Block

8Model No.: ACF552
SUPPLY CABLE
TERMINAL BLOCK
(on Hanger Bracket)
BLACK WIRE
(Neutral)
RED WIRE (Active)
FROM WALL FAN
CONTROL SWITCH
BLUE WIRE
(Neutral)
NL1 L
GREEN/YELLOW
WIRE (Earth)
FROM
HANGER
BRACKET
RED OR WHITE WIRE
(Active) FROM WALL
LIGHT SWITCH
GREEN/YELLOW
WIRE (Earth)
GREEN/YELLOW
WIRE (Earth)
FROM HANGER
BRACKET
BROWN WIRE
(Motor Active)
GREEN/YELLOW
WIRE (Earth)
FROM FAN
ORANGE WIRE
(Light Active)
GREEN/YELLOW
WIRE (Earth)
FROM HANGER
BALL
1-PIN
CONNECTORS
HANGER
BRACKET
HANGER
BALL
Figure 16
THREADED
STUDS (2)
#8 LOCKWASHER
KNURLED KNOB
CANOPY
SEAL PAD
CEILING
COVER
To avoid possible fire or shock, make sure that the
electrical wires are not pinched between the ceiling
cover and the ceiling.
WARNING
Figure 17
1. Screw the two #8-32 x 1-1/4” threaded studs
(supplied) into the tapped holes in the hanger
bracket (Figure 17).
2. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 17).
Final Installation
Using Your Ceiling Fan
1. Restore electrical power to the ceiling fan by
turning the electricity on at the main fuse box.
2. Check the operation of the fan turning the wall fan
control switch to the "ON" position.
3. All fans are shipped from the factory with the
reversing switch positioned to circulate air
downward. If airflow is desired in opposite
direction, turn your fan OFF and wait for the blades
to stop turning, then slide the reversing switch to
the opposite position, and turn fan on again. The
fan blades will turn in the opposite direction and
reverse the airflow (Figure 18).
NOTE: Be sure the canopy seal pad extends outside
the ceiling cover.
3. Secure the ceiling cover in place by sliding the
#8 lockwashers over the threaded studs and
installing the two knurled knobs (supplied)
(Figure 17). Tighten the knurled knobs securely until
the ceiling cover fits snugly against the ceiling.
Your fan is now wired to be turned on and off from
the wall switch.
7. Securely connect the branch circuit supply cable
green/yellow earth wire to the hanger bracket
terminal block marked (Figure 16).
8. Securely connect the branch circuit supply cable
black (Neutral) wire to the hanger bracket terminal
block marked N (Figure 16).
9. Securely connect the branch circuit motor supply
cable Red or White (active) wire to the hanger
bracket terminal block marked L (Figure 16).
10.Securely connect the branch circuit lighting supply
cable Red (active) wire to the hanger bracket
terminal block marked L1 (Figure 16).
11.After connections have been made, carefully push
leads into the recess making sure there is
separation between connectors. If required, the
fan wires can be trimmed to more easily fit within
the ceiling cover.
Protruding bare wire or wire strands at the terminal
block creates the possibility of an electrical shock.
Do not operate the fan until the terminal block
connections are completely enclosed within the
insulated terminal ports. All supply wires shall be
securely connected to the terminal block, no loose
wire shall be present.
WARNING
Supply Connections To Terminal Block
Protruding bare wire or wire strands at the terminal
block creates the possibility of an electrical shock. Do
not operate the fan until the terminal block connections
are completely enclosed within the insulated terminal
ports. All wires from the fan, hanger ball and hanger
bracket shall be securely connected to the terminal
block, no loose wire shall be present.
WARNING

9Model No.: ACF552
REVERSING
SWITCH
Figure 18
Reverse Switch Information
Season Rotation Direction
Summer Counter-Clockwise
Winter Clockwise
WARNING: For your own safety, turn off power at fuse box or circuit breaker before trouble shooting your fan.
Some suggested remedies require the attention of a licensed electrician.
Trouble Shooting
TROUBLE PROBABLE CAUSE SUGGESTED REMEDY
1. Fan will not start. 1. Fuse blown or isolation switch and/or 1. Check main and branch circuit fuses and
RCD (Safety Switch) tripped. isolation switches and RCD (Safety Switch).
2. Loose power line connections to the fan, 2. Check line wire connections to fan and switch
or loose switch wire connections in the wire connections in the switch housing.
switch housing. WARNING: Make sure main power is
turned OFF.
3. Reversing switch in neutral position. 3. Make sure reversing switch position is all the
way to one side.
2. Fan sounds noisy. 1. Blades not attached to fan. 1. Attach blades to fan before operating.
2. Loose screws in motor housing. 2. Check to make sure all screws in motor
housing are snug (not over-tight).
3. Screws securing fan blade flanges to 3. Check to make sure the screws which attach
motor hub are loose. the fan blade flanges to the motor hub are tight.
4. Wire connectors inside switch housing 4. Check to make sure wire connectors in switch
rattling. housing are not rattling against each other or
against the interior wall of the switch housing.
WARNING: Make sure main power is
turned OFF.
5. Screws holding blades to blade flanges 5. Tighten screws securely.
are loose.
3. Fan wobbles 1. Setscrews in motor coupling are loose. 1. Tighten both setscrews securely in the motor
excessively. coupling.
2. Setscrew in hanger ball/downrod 2. Tighten the setscrew in the hanger ball/
assembly is loose. downrod assembly.
3. Screws securing fan blade flanges to 3. Check to be sure screws which attach the fan
motor are loose. blade flanges to the motor are tight.
4. Fan blade flanges not seated properly. 4. Check to be sure the fan blade flanges seat
firmly and uniformly to the surface of the motor.
If blade flanges are seated incorrectly, loosen
the blade flange screws and retighten
according to the procedure in the section on
"Assembly Instructions".
5. Hanger bracket is not securely 5. Tighten the hanger bracket screws to the
fastened to the ceiling joist. ceiling joist.
6. Fan blades out of balance. 6. Interchanging an adjacent (side-by-side) blade
pair can redistribute the weight and result in
smoother operation.
!
!
!
Accessories
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.
1. Ceiling Fan Light Kits (see store or website:
www.myfan.com.au).
2. Ceiling Fan/Light Controls (see store or website:
www.myfan.com.au).
3. Downrod Extension Kits (see store or website:
www.myfan.com.au).
WARNING
!
WARNING
!

15
16
21
20
11
5
4
10
19
17
18
12
3
2
6
14
13
7
8
9
1
Repair Parts
Model No.: ACF552
10
Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
WARNING

11
Repair Parts Listing
Part Numbers
Key Model No. Model No.
No. Description ACF552ORB00 ACF552WW00
*HangerBallAssembly, 761655-32 761655
Consisting of:
1HangerBracket — —
2HangerBall — —
3Downrod — —
*PartsBagContaining: 763913-BLOXSS763913-SS
4Pin,Clevis(1) — —
5Clip,Hairpin(1) — —
6Stud,Threaded,#8-32x1-1/4”(2) — —
7Lockwasher,ExternalTooth,#8(2) — —
8Nut,Knurled,#8-32(2) — —
9Screw,SerratedPanHead,
M4 x 10mm (1) — —
10 Screw, Flat Head, M4 x 12mm (1) — —
11 Screw, Washer Head Blade (16) — —
12 Screw, M6 x 14mm Pan Head
with Lockwasher (1) — —
13 Balancing Kit (1) — —
14 Pad, Canopy Seal 764376 764376
15 Cover, Ceiling 763921-ORB 763921-WW
16 Cover, Coupling 764054-ORB 764054-WW
17 Harness, Wiring 764375-BLK 764375-WW
18 Switch Cup Cover 763915-ORB 763915-WW
19 Switch Cup 763919-ORB 763919-WW
20 Fan Blades (set of 5) 763910-ORB 763910-WW
21 Blade Flanges (set of 5) 763908-ORB 763908-WW
—Owner's Manual BP7461 BP7461
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
•PART NUMBER •NAME OF ITEM
•PART DESCRIPTION •MODEL NUMBER
The model number of your Fan will be found on a label attached to the top housing.
For repair parts:
Model No.: ACF552
Ceiling fan performance and energy savings
rely heavily on the proper installation and use
of the ceiling fan. Here are a few tips to ensure
quality and product performance.
Choosing the Appropriate Mounting
Location. Ceiling fans should be installed, or
mounted, in the middle of the room and at
least 2.1 m above the floor and 50 cm from the
walls. If ceiling height allows, install the fan
2.4m - 2.7m above the floor for optimal airflow.
Using the Ceiling Fan Year Round. In the
summer, use the ceiling fan in the counter-
clockwise direction. The airflow produced by
the ceiling fan creates a wind-chill effect,
making you "feel" cooler. Select a fan speed
that provides a comfortable breeze, lower
speeds consume less energy. In the winter,
reverse the motor and operate the ceiling fan
at low speed in the clockwise direction. This
produces a gentle updraft, which forces warm
air near the ceiling down into the occupied
space. Remember to adjust your AIRCON
thermostat when using your ceiling fan -
additional energy and dollar savings could be
realized with this simple step!
Turn Off When Not in the Room. Ceiling
fans cool people, not rooms. If the room is
unoccupied, turn off the ceiling fan to save
energy.
Energy Efficient Use of
Ceiling Fans
Phone: [phone]
[email protected]
www.myfan.com.au

MyFan Warranty for Australian Purchasers
Part No. F40BP74610000 Form No. BP7461
Printed in China 05/13
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Model No.: ACF552
Call Fax Email Mail
1300 469 326 (07) 3801 8575 [email protected] My Fan Pty Ltd
PO Box 6560
Visit us online at www.myfan.com.au GCMC QLD 9726
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a refund
or replacement for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount
to a major failure. All products have been imported in good faith from the overseas manufacturer.
The following warranty only covers faults due to manufacturing defects in materials or workmanship.
Only orders placed through My Fan Pty Ltd ( “MyFan” ) or authorized sales partner are covered by this warranty.
By purchasing from an Authorized Partner or directly from MyFan, your products are now covered by our 12 month on-site
warranty. Should your fan fail within the first 12 months, MyFan (at our sole discretion and conditional on the limitations
outlined in Section 4) will repair or replace the faulty component.
Section 1: What to do if your fan has a problem
Section 2: MyFan 12 month on-site warranty
Should your fan’s motor fail during its lifetime, due to a defect in materials or workmanship, MyFan (at our sole discretion and
conditional on the limitations outlined in Section 4) will repair or replace the motor.
Section 3: MyFan limited lifetime motor warranty
After the 12 month on-site warranty period, all costs of removal and/or re-installation of the product are the sole responsibility
of the owner or their representative and not the supplier that sold the fan or MyFan.
You must have proof of your purchase to obtain any after sales service. Keep your tax invoice or other proof of purchase
together with the installing electrician’s details. Do not uninstall or attempt to return the product to the supplier or MyFan unless
advised to by MyFan. You must be the original purchaser of the product and it must be installed in its original point of
installation to be covered by this warranty. Warranty periods begin from the date of purchase. Because of varying climate
conditions, this warranty does not cover changes in finish, including rusting, pitting, corroding, tarnishing or peeling.
The warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to
extremes of heat or humidity or as a result of any modification to the original product. Force majeure, electrical surges,
lightning, power grid fluctuations, water or by connection to alternative power supply sources (such as solar inverters) are not
eligible for claims.
If electricians are engaged by MyFan to service fans that are installed in a location requiring special access equipment (such
as scaffolding, scissor lifts, etc.) the cost of providing, installing and operating the special access equipment must be borne by
the site owner. The need for or use of such equipment must be stated when booking a service call.
MyFan reserves the right to charge for travelling costs incurred beyond 25km from Australian major capital cities. Travelling
costs or other expenses must be agreed to prior to a service call being booked.
Signals sent through the power grid by the electricity supplier for the control of devices may cause intermittent noise in your
product. These noises are not the result of a faulty product. Filters are available at the customer’s expense.
A certain amount of wobble is normal and should not be considered a problem or a defect.
Solid state or dimmer controls may damage your fan. Use of controllers not approved by MyFan will void your warranty.
Section 4: Limitations of warranty
Satisfy yourself that there is
not an installation problem.
1Do NOT attempt to uninstall
or repair your fan.
2Call 1300 469 326 for further
assistance.
3